ESP Peugeot 307 2007.5 Owner's Guide

10PRACTICAL INFORMATION
132
The electrical system of your vehicle is designed to operate with standard or optional equipment
Before installing other electrical equipment or accessories on yo ur vehicle, contact a PEUGEOT dealer.
PEUGEOT will not accept responsibility for the cost incurred in re pairing your vehicle or for rectifying the malfunctions
resulting from the installation of accessories not supplied and not recommended by PEUGEOT and not installed in
accordance with its instructions, in particular when the combined consumption of all of the additional equipment connected
exceeds 10 milliamperes.

Fuse N° Rating
Functions

MF1 **
30 A 200 W fan unit.

50 A 400 W and 460 W fan unit.

MF2 ** 30 A ABS/ESP pump.

MF3 ** 30 A ABS/ESP solenoid valves.

MF4 ** 80 A Built-in systems interface supply.

MF5 ** 80 A Built-in systems interface supply.

MF6 ** 80 A Passenger compartment fuse box.

MF8 ** 70 A Power steering electro-pump unit.
** The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried out by
a PEUGEOT dealer.

10PRACTICAL INFORMATION
Special front windscreen
wiper position

 Within one minute of switching off
the ignition, operate the wipers
stalk to position the wiper blades
in the centre of the windscreen
(maintenance position).
Changing a wiper blade

 Lift the wiper arm, then unclip the
blade and remove it.

 Fit the new blade and push back
the arm.

Note: the shortest blade is i tted on
the vehicle’s right-hand windscreen
wiper arm.

To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wiper
stalk.
BATTERY
To charge the battery using a
battery charger:
- Disconnect the battery starting
with the negative (-) terminal,
- Follow the instructions for use given by the battery charger
manufacturer,
- Check that the terminals and connectors are clean; if they are
covered with sulphate (white or
greenish deposit), disconnect
them and clean them,
- Reconnect the battery starting with the negative (-) terminal. Before disconnecting the
battery, you must wait for
2 minutes after switching off
the ignition.
Never disconnect a terminal when
the engine is running.
Never charge a battery without i rst
disconnecting the terminals.
Close the windows and sunroof
before disconnecting the battery.
If they do not operate normally
following reconnection of the
battery, they must be reinitialised
(see sections "Reinitialisation of the
electric windows" and "Sunroof").
After every reconnection of the
battery, switch on the ignition and
wait 1 minute before starting to
allow the electronic systems to be
initialised. If slight difi culties are
experienced after this, please contact
a PEUGEOT dealer.
Following disconnection of the battery,
the remote control key and the GPS
satellite navigation system must
be reinitialised (see corresponding
section).
It is advisable to disconnect the
battery if the vehicle is not to be
used for a period of more than
one month.
To start the vehicle from another
battery:
- Connect the red cable to the positive (+) terminals of the two
batteries,
- Connect one end of the green or black cable to the negative (-)
terminal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
-
Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables. The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used remote control and vehicle
batteries to an approved collection
point.
CHANGING A WINDSCREEN
WIPER BLADE

11TECHNICAL DATA
143
The consumption values presented here correspond to the values communicated at the time of printing. These consumption values
were established in accordance with EC Directive 80 /1268 (as amended). They may vary depending on the style of driving, driving
conditions, weather conditions, the vehicle load, t he maintenance of the vehicle and the use of the ac cessories.
(1) Unleaded. - (2) E85.
SALOON CONSUMPTION In accordance with EC Directive 80/1268 (as amended)

Engine Gearbox
Model
codes:
3A... 3C...
Urban Circuit
mpg
(litres/100 km)
Inter-urban
Circuit mpg
(litres/100 km)
Mixed Circuit
mpg
(litres/100 km)
Emission
of CO
2 by
weight (g/km)

1.4 litre 16V Manual KFUC 32.4 (8.7) 53.3 (5.3) 43.5 (6.5) 155

1.6 litre 16V Manual
NFUC 28.2 (10.0) 48.7 (5.8) 38.1 (7.4) 174

NFUL 28.2 (10.0) 48.7 (5.8) 38.1 (7.4) 174
Automatic NFUF 25.3 (11.2) 47.1 (6.0) 35.8 (7.9) 189

1.6 l. 16V BioFlex Manual NFUC/FF 28.2 (10.0) (1)
20.6 (13.7) (2) 48.7 (5.8) (1)
35.7 (8.0) (2) 38.1 (7.4) (1)
28.0 (10.1) (2) 174 (1)
165 (2)

2 litre 16V 143 bhp Manual
RFJC 26.4 (10.7) 47.1 (6.0) 36.7 (7.7) 184
Automatic RFJF 23.9 (11.8) 45.6 (6.2) 34.4 (8.2) 195

1.6 l. Turbo HDI 16V
90 bhp Manual
9HXC 46.3 (6.1) 65.7 (4.3) 57.6 (4.9) 129

9HVC 46.3 (6.1) 65.7 (4.3) 57.6 (4.9) 129

1.6 litre Turbo HDI
16V 110 bhp Manual
9HZC 46.3 (6.1) 65.7 (4.3) 57.6 (4.9) 129

9HYB 47.1 (6.0) 67.2 (4.2) 60.0 (4.8) 126

9HYC 45.6 (6.2) 45.6 (6.2) 56.5 (5.0) 132

2 litre Turbo HDI
16V Manual
RHRH 39.8 (7.1) 62.8 (4.5) 52.4 (5.4) 142
Automatic RHRJ 30.4 (9.3) 54.3 (5.2) 42.2 (6.7) 178

11TECHNICAL DATA
144
The consumption values presented here correspond to the values communicated at the time of printing. These consumption va-
lues were established in accordance with EC Directi ve 80/1268 (as amended). They may vary depending on the style of driving,
driving conditions, weather conditions, the vehicle load, the maintenance of the vehicle and the use o f the accessories.

VAN CONSUMPTION In accordance with EC Directive 80/1268 (as amended)

Engine Gearbox
Model
codes
3G...
3X...
Urban circuit
mpg
(litres/100 km)
Inter-urban
circuit mpg
(litres/100 km)
Mixed circuit
mpg
(litres/100 km)
Emission of
CO
2 by
weight (g/km)

1.4 litre 16V Manual KFUC 32.4 (8.7) 53.3 (5.3) 43.5 (6.5) 155

1.6 litre Turbo HDI
16V 90 bhp Manual
9HXC 46.3 (6.1)
46.3 (6.1) 65.7 (4.3)
65.7 (4.3) 57.6 (4.9)
57.6 (4.9) 129
129

1.6 litre Turbo HDI
16V 110 bhp Manual
9HZC 46.3 (6.1) 65.7 (4.3) 57.6 (4.9) 129

9HYB 47.1 (6.0)
45.6 (6.2) 67.3 (4.2)
65.7 (4.3) 60.1 (4.8)
57.6 (4.9) 126
132

9HYC 45.6 (6.2)
45.6 (6.2) 65.7 (4.3)
65.7 (4.3) 56.5 (5.0)
57.6 (4.9) 132
132

11TECHNICAL DATA
145

ESTATE CONSUMPTION In accordance with EC Directive 80/1268 (as amended)

Engine Gearbox
Model
codes
3E...
Urban circuit
mpg
(litres/100 km)
Inter-urban
circuit mpg
(litres/100km)
Mixed circuit
mpg
(litres/100 km)
Emission of
CO
2 by
weight (g/km)

1.4 litre 16V Manual KFUC 32.1 (8.8) 51.4 (5.5) 42.2 (6.7) 159

1.6 litre 16V Manual
NFUC 28.5 (9.9) 44.8 (6.3) 36.7 (7.7) 178
Automatic NFUF 24.8 (11.4) 44.8 (6.3) 34.0 (8.3) 194

1.6 l. 16V BioFlex Manual NFUC/FF 28.5 (9.9) (1)
20.3 (13.9) (2) 44.8 (6.3) (1)
33.2 (8.5) (2) 36.7 (7.7) (1)
27.2 (10.4) (2) 178 (1)
169 (2)

2 litre16V 143 bhp Manual
RFJC 25.7 (11.0) 46.3 (6.1) 35.8 (7.9) 188
Automatic RFJF 23.2 (12.2) 44.8 (6.3) 33.4 (8.4) 199

1.6 litre Turbo HDI
16V 90 bhp Manual
9HXC 45.6 (6.2) 64.2 (4.4) 56.5 (5.0) 131

9HVC 45.6 (6.2) 64.2 (4.4) 56.5 (5.0) 131

1.6 litre Turbo HDI
16V 110 bhp Manual
9HZC 45.6 (6.2) 64.2 (4.4) 56.5 (5.0) 131

9HYB 46.3 (6.1) 65.7 (4.3) 57.6 (4.9) 128

9HYC 44.8 (6.3) 64.2 (4.4) 55.4 (5.1) 134

2 litre Turbo HDI
16V Manual
RHRH 38.7 (7.3) 60.1 (4.7) 50.4 (5.6) 148
Automatic RHRJ 29.7 (9.5) 52.4 (5.4) 40.9 (6.9) 183
The consumption values presented here correspond t o the values communicated at the time of printing. These consumption va-
lues were established in accordance with EC Directi ve 80/1268 (as amended). They may vary depending on the style of driving,
driving conditions, weather conditions, the vehicle load, the maintenance of the vehicle and the use o f the accessories.
(1) Unleaded. - (2) E85.

173
1
SOURCE
2
S
O S SOURCE
MODE BAND T
PTA YDARK
SOURCE
2abc5jkl8tuv
3def6mno9wxyz
1 4
ghi7pqrs
0 #
2abc5jkl8tuv
3def6mno9wxyz
1 4ghir7pq s0 #
S
O S SOURCE
MODE BAND T
PTA YDARK
SOURCESOURCE
ESC
MENU LIST
1
3
2Press the MENU button then select the CONFIGURATION
function,
then SOUNDS, then ACTIVATE AUXILIARY SOURCE to acti vate
the auxiliary input of the RT4 GPS audio/telephone.
Connect the portable equipment (MP3
player…) to the audio sockets (white and
red, RCA type) located in the glove box
using a JACK/RCA audio cable.
Press the SOURCE button several
times in succession and select AUX. Insert one or more CDs in the
changer.
Press the SOURCE button several
times in succession and select CD
CHANGER.
Press one of the buttons on the
alphanumeric keypad to select the
corresponding CD.
Press one of the buttons to select a
track on the CD.
The displaying and management of the commands takes place via
the portable equipment.
It is not possible to copy the iles onto the hard d isc from the auxiliary
input. It is not possible to copy the iles onto the hard d
isc from the
CD changer.
USING THE AUXILIARY INPUT (AUX)
JACK/RCA AUDIO CABLE NOT SUPPLIED
CD CHANGER
PLAYING A CD (NOT MP3 COMPATIBLE)

195
The table below groups together the answers to the most frequently asked questions concerning the RD4 audio equipment and the RT4 audio/telephone.
QUESTION SOLUTION
RESPONSE
There is a difference in
sound quality between
the different audio
sources (radio, CD, CD
changer...). Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-Rear
Balance, Left-Right Balance) to the middle
position, select the musical ambience "None"
and set the loudness correction to the "Active"
position in CD mode or to the "Inactive" position
in radio mode.
For optimum sound quality, the audio settings (Volu
me, Bass, Treble,
Ambience, Loudness) can be adapted to the different sound sources,
which may result in audible differences when changi ng source
(radio, CD, CD changer...).
The CD is ejected
automatically or is not
played by the player. - Check that the CD is inserted in the player the
right way up.
- Check the condition of the CD: the CD cannot be played if it is too damaged.
- Check the content in the case of a recorded CD: consult the advice in the Audio section.
- The audio equipment’s CD player does not play DVDs.
- Due to inadequate quality, certain recorded CDs will not be played by the audio system.
- The CD changer does not play MP3 CDs.
The CD is inserted upside down, is unplayable, does
not contain any audio
data or contains an audio format which the player c annot play.
The CD is protected by an anti-pirating protection system which is not
recognised by the audio equipment.
FREQUENTLY ASKED QUESTIONS
The CD player sound
is poor. The CD used is scratched or of poor quality. Insert
good quality CDs and store them in
suitable conditions.
The audio equipment settings (bass, treble, ambienc es) are unsuitable.Set the treble or bass level to 0, without selectin g
an ambience.

196
QUESTIONSOLUTION
RESPONSE
The stored stations do
not function (no sound,
87.5 Mhz is displayed...) An incorrect waveband is selected.
Press the BAND AST button to return to the
waveband (AM, FM1, FM2, FMAST) on which the
stations are stored.
The trafic announcement
(TA) is displayed. I do
not receive any trafic
information.Tune to a radio station which broadcasts trafic
information.
The radio station is not part of the regional trafi
c information network.
The quality of reception
of the radio station
listened to gradually
deteriorates or the
stored stations do
not function (no
sound, 87.5 Mhz is
displayed...). The vehicle is too far from the transmitter used by
the station listened to or
there is no transmitter in the geographical area th rough which the vehicle
is travelling.
The environment (hills, buildings, tunnels, basemen t car parks...) block
reception, including in RDS mode.
The aerial is absent or has been damaged (for examp le when going
through a car wash or into an underground car park) .Activate the RDS function to enable the system
to check whether there is a more powerful
transmitter in the geographical area.
This phenomenon is normal and does not
indicate a failure of the audio equipment.
Have the aerial checked by a PEUGEOT dealer.
Sound cut-outs of 1
to 2 seconds in radio
mode. During this brief sound cut-out, the RDS searches f
or any frequency
permitting better reception of the station. Deactivate the RDS function if the phenomenon
is too frequent and always on the same route.
With the engine off,
the audio equipment
switches off after a
few minutes of use. When the engine is switched off, the audio equipmen
t operating time
depends on the battery charge.
The switch-off is normal: the audio equipment switc hes to economy mode
and switches off to prevent discharging of the vehi cle’s battery.Start the vehicle’s engine to increase the battery
charge.
The message "the audio
system is overheated"
appears on the display. Switch the audio system off for a few minutes to
allow the system to cool.
In order to protect the installation if the surroun
ding temperature is too
high, the audio equipment switches to an automatic thermal protection
mode leading to a reduction of the volume or stoppi ng of the playing of the
CD.

197
QUESTIONSOLUTION
RESPONSE
The TRAFFIC INFO
box is ticked. However,
certain trafic jams
along the route are not
indicated in real time. On starting, it is several minutes before the syste
m begins to receive the
trafic information. Wait until the trafic information is being received

correctly (displaying of the trafic information
symbols on the map).
In certain countries, only major routes (motorways, ...) are listed for the
trafic information.
The time taken to calculate
a route sometimes seems
longer than usual.
This phenomenon is normal. The system is
dependent on the trafic information available.
The performance of the system may slow down tempora rily if a CD is
being copied onto the Jukebox at the same time as a route is being
calculated. Wait until the CD has been copied or stop the
copying before starting the guidance function.
Does the emergency call
function work without a
SIM card? No, European regulations impose the presence of a S
IM card in order to
make an emergency call. Insert a valid SIM card in the slot on the RT4 GPS
audio/telephone.
My SIM card is not
recognised. The RT4 accepts 3.3 V SIM cards, the old 5 V and 1.
8 V SIM cards are not
recognised. Contact your telephone operator.
After changing a wheel,
the system loses its
location. The RT4 GPS audio/telephone uses the wheel rotation
information to
improve the GPS locating function. If a wheel is ch anged or delates
suddenly, the system recalculates the location. For approximately
ten minutes, this recalculation may affect the qual ity of the locating function.Wait until the system has completed its
recalculation.
The table below groups together the answers to the
most frequently asked questions concerning the RT4 audio/telephone.
The location on the
map is incorrect or
inaccurate.
The altitude is not
displayed. On starting, the initialisation of the GPS may take
up to 3 minutes to
receive more than 3 satellites correctly. Wait until the system has started up completely.
Check that there is a GPS coverage of at least 3
satellites (long press on the MENU button, then
select AUDIO/TELEPHONE DIAGNOSTICS, then
GPS COVERAGE).
Depending on the geographical environment (tunnel, ...) or the weather,
the conditions of reception of the GPS signal may v ary.This phenomenon is normal. The system is
dependent on the conditions of reception of the
GPS signal.

188
1
2
3
12
Insert the CDs in the changer one by
one.
Press the SOURCE button several
times in succession and select CD
CHANGER.
Press one of the buttons on the
numeric keypad to select the
corresponding CD.
Press one of the buttons to select a
track on the CD.
Press and hold one of the buttons for
fast forwards or backwards play. Insert circular compact discs only.
Some anti-pirating systems, on original discs or CD
s
copied using a personal recorder, may cause faults
which are no relection on the quality of the origin al
player.
Without pressing the EJECT button, insert a CD in t he
player, play begins automatically.
To play a disc which has already been
inserted, press the SOURCE button
several times in succession and select
CD. Press one of the buttons to select a
track on the CD.
Press the LIST REFRESH button to
display the list of tracks on the CD.
CD CHANGER
PLAYING A CD (NOT MP3 COMPATIBLE)
CD
PLAYING A CD