brake Peugeot 307 SW Dag 2003 Owner's Guide

14-04-2003
CHANGING A WHEEL
Tools The following tools are located:
Ð in the right-hand trim of the boot,1 - Wheelbrace.
2 - Removable towing eye.
3 - Socket for anti-theft bolts.
Ð in the holder in the centre of the spare wheel, 4 - Jack with handle.
5 - Bolt cover tools.
6 - Centralising tool.
7 - Removable chock. Parking the vehicle 
As far as possible, park the vehicle on level, stable and non-slippery ground.
 Apply the handbrake, switch offthe ignition and engage first orreverse gear (position Pfor the
automatic gearbox). Access to the spare wheel 
Open the boot.
 Open the flap using the lug to release the winch and gainaccess to its control nut.
 Unscrew the nut fully, using thewheelbrace 1, to unroll the winch
cable.
PRACTICAL INFORMATION 141

14-04-2003
PRACTICAL INFORMATION143
For your safety, always change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with first or reverse gear enga- ged (position Pfor the automatic
gearbox),
- with the vehicle chocked. Never go underneath a vehicle that is supported only by a jack(use a ramp) Never refit the holder under the vehicle without the sparewheel. After changing the wheel:
- have the correct positioning of the punctured wheel, the tighte- ning of the bolts and the tyrepressure checked by a PEUGEOT dealer as soon aspossible.
- have the punctured tyre repai- red and refit it to the vehicle assoon as possible.
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer. Close the flap using the lug to lock the winch.
 Store the rest of the tools in theright-hand trim of the boot.
Fitting a wheel 
Position the wheel using the cen- tralising tool 5to assist you.
 Tighten the bolts by hand andremove the centralising tool 5.
 Partly tighten the bolts using thewheelbrace 1.
 Fold the jack 4and remove it.
 Fully tighten the bolts using thewheelbrace 1.
 Replace the wheel trim, startingby placing the wheel trim notchopposite the valve, and press iton using the palm of the hand.
 Put the corresponding tools in
the holder and secure its cover.
 Place the holder on the groundand align the spare wheel on it.
 Pass the notched hook into the
holder cover.
 Refit the wheel under the vehicletightening the winch control nutusing the wheelbrace 1.
 Fully tighten and check that the
wheel is horizontally flush
against the rear floor.

14-04-2003
PRACTICAL INFORMATION147
Third brake light: 4 W 5 W bulbs.  Remove the tailgate upper trim carefully by unclipping it on eitherside, perpendicular to its direc-tion of engagement.
 Insert a screwdriver into the twoouter holes Bto press on the two
tabs C.
 Push the light unit outwards whilemaintaining the pressure on thetabs.
 Pull the light unit outwards whiletilting it.
 Change the faulty bulb.
 When refitting, ensure that thelight unit tabs are engaged cor-rectly and that the tailgate uppertrim has been put back in place
correctly.
Remove the bulb holder pressing on the tabs A,
 Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts. When refitting, take care to position
the bulb holder and the light correctly.
Number plate lights (W 5 W)  Insert a thin screwdriver into one of the external holes of the lens.
 Push it outwards to unclip it.
 Remove the lens.
 Change the faulty bulb.
Rear lights
1 - Brake lights (P 21 W).
2 - Side lights (R 5 W).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W), right
side.
Fog lamp (P 21 W), left side.
These 5 bulbs are changed by remo- ving the light:  Remove the corresponding boot side trim to access the light,
 Remove the light fixing nut insidethe boot,
 Remove the light fixing nut outsidethe boot,
 Remove the light,
 Unclip the harness,

CHANGING A FUSE The fuse boxes are located under the fascia (driver's side) and in theengine compartment. The spare fuses and special pliers A
are fixed to the inside of the lid of the fascia fuse box. Removing and changing a fuse Before changing a fuse you must establish the cause of the fault and
have it corrected. The fuse numbersare indicated on the fuse box.  Use the special pliers A.
Always change a faulty fuse for one of the same rating. Fascia fuses 
Unscrew the bolt a quarter of a turn with a coin, then pull thehandle to open the cover andaccess the fuses.
PRACTICAL INFORMATION
148
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Front electric windows.
5 15 A Left brake light including trailer.
7 30 A Rear courtesy light, front courtesy light, map readers - 12 V front socket - Glove box lighting - Concealing flap control.
Correct
Pliers AIncorrect
14-04-2003

CHANGING A FUSE The fuse boxes are located under the fascia (driver's side) and in theengine compartment. The spare fuses and special pliers A
are fixed to the inside of the lid of the fascia fuse box. Removing and changing a fuse Before changing a fuse you must establish the cause of the fault and
have it corrected. The fuse numbersare indicated on the fuse box.  Use the special pliers A.
Always change a faulty fuse for one of the same rating. Fascia fuses 
Unscrew the bolt a quarter of a turn with a coin, then pull thehandle to open the cover andaccess the fuses.
PRACTICAL INFORMATION
148
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Front electric windows.
5 15 A Left brake light including trailer.
7 30 A Rear courtesy light, front courtesy light, map readers - 12 V front socket - Glove box lighting - Concealing flap control.
Correct
Pliers AIncorrect
14-04-2003

14-04-2003
PRACTICAL INFORMATION149
Fuse no. Rating
Functions
9 30 A Front electric windows - Front press operation windows (incompatible with non-press opera- tion windows) - Panoramic roof concealing flap.
10 15A Diagnostic socket - 12 V rear socket - Trailer.
11 20A Audio equipment - Multi-function display - Steering wheel controls - Automatic gearbox.
12 10A Front right and rear right side lights - Number plate and trailer lighting - Central locking
switches/ alarm/hazard warning lights lighting- Air conditioning/ashtray light - Heated seats
switches/automatic gearbox lighting- Lighter.
14 30 A Door opening/closing controls - Deadlocking controls.
15 30A Press-operation electric rear windows.
16 10A Engine fuse box - Alarm - Particulate emission filter - Steering wheel controls - Air bags.
17 10A Rear right brake light, 3rd brake light.
18 10 A Diagnostic socket - Steering wheel controls - Electrochromatic mirror - Brake pedal (stop)and clutch switches - Coolant level switch - Second brake switch.
19 30 A PARC shunt.
22 10 A Front left and rear left side lights - Number plate and trailer lighting.
23 15 A Alarm siren - Interior alarm control unit.
24 15 A Instrument panel - Audio equipment - Multi-function displays - Air conditioning - Rear parking aid.
26 30 A Heated rear screen.

14-04-2003
PETROL
Engine 1,6 litre 16V 2 litre 16V
Gearbox Manual Automatic Manual Automatic
Model codes : 3HNFUB 3HNFUE 3HRFNC/IF 3HRFNE 3HNFUC/IF 3HNFUF/IF
¥ Kerb weight 1399 1435 1430 1466
¥ Gross vehicle weight (GVW) 1923 1959 1941 1977
¥ Gross train weight (GTW*) 3023 3059 3441 3477
¥ Unbraked trailer 695 715 715 730
¥ Braked trailer (within GTW) 1100 1100 1500 1500
TECHNICAL DATA 163
Weights and Towing loads (in kg)
* The speed of a towing vehicle is limited to 60 mph (100 km/h). DIESEL
Engine 2 litre Turbo HDI 90 hp 2 litre Turbo HDI 110 hp
Gearbox Manual Manual
Model codes : 3HRHYB 3HRHSB
¥ Kerb weight 1465 1496
¥ Gross vehicle weight (GVW) 1984 2016
¥ Gross train weight(GTW*) 3484 3516¥ Unbraked trailer 730 745
¥ Braked trailer (within GTW) 1500 1500