change time PEUGEOT 4008 2014 User Guide

118Driving

Manual gear changing

In the automated mode, you can take over
control temporarily at any time using the
steering mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster change down than that offered
in automated mode (arrival at a roundabout,
exit from a car park with a steep gradient,
over taking...).
The gearbox engages the gear requested if
the engine speed permits it. The gear engaged
appears.
To return to the automated mode, do one of the
following:


- press the back of the "+/OFF"
steering
mounted control 3
for approximately
2 seconds,

- move the gear lever quickly towards
position +/-
and then return it to position D
,

- stop the vehicle.




Stopping the vehicle
Operating fault

With the ignition on, if the message
"Slow down"
or "Service required"
appears
in the instrument panel screen, this indicates a
gearbox malfunction.
When a message is displayed, carry out the
following operations:


- slow down and stop your vehicle in a safe
place,

- place the lever in position P
and let the
engine run,

- open the bonnet to allow the engine to
cool.
If the message disappears for a long period,
you can set off again.
If the message remains displayed or appears
frequently, contact a PEUGEOT dealer or a
qualified workshop without delay. Before switching off the engine, you must place
the gear lever in position P
.
You must apply the parking brake to immobilise
the vehicle.

190
Practical information












Changing sidelamp
bulbs (4)


)
Remove the protective plastic cover.

)
Turn the bulb holder to the left and pull it
out.

)
Remove the bulb and its base by pressing
on the lug at the bottom.

)
Change the bulb.
For reassembly, carry out these operations in
reverse order.









Changing main beam headlamp
bulbs (2)


)
Turn the bulb holder a quarter turn to the
left and pull it out.

)
Pull out the bulb and replace it.
To reassemble, carry out these operations in
reverse order.


Changing the daytime
running lamps / sidelamps
(light- emitting diodes - LEDs) (6)
For the replacement of this type of LED lamp,
contact a PEUGEOT dealer or a qualified
workshop.









Changing dipped headlamp
bulbs (3)
For the replacement of these bulbs, contact a
PEUGEOT dealer or a qualified workshop.

To replace these bulbs contact a PEUGEOT
dealer or a qualified workshop.












Changing front foglamp
bulbs (7) / daytime running
lamp bulbs (5)

219
8
Checks






Checking levels


Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start at
any time (even with the ignition off).


















Oil level


The check of the the level is done
out with the dipstick, located under
the bonnet. Refer to the description
of your engine compartment for the
position of the dipstick.
Engine oil change

Refer to the warranty and maintenance record
for details of the inter val for this operation.
In order to maintain the reliability of the engine
and emission control system, the use of
additives in the engine oil is prohibited.


Oil specifi cation

The oil must be the correct grade for your
engine and conform to the manufacturer's
recommendations.

Check all of these levels regularly, in line with the warranty and maintenance record. Top them up if necessary, unless other wise indicated.
If a level drops significantly, have the corresponding system checked by a PEUGEOT dealer or a qualified workshop.



















Dipstick

There are two marks on the dipstick:

A
= maximum
If the level is above this
mark, contact a PEUGEOT
dealer or a qualified
workshop.

B
= minimum
Top up the level through the
oil filler orifice, using the
correct grade of oil for your
engine. The level must never
be below this mark.
This check will only be correct if the vehicle is
on level ground and the engine has been off for
more than 30 minutes.
It is normal to top up the oil level between
two ser vices (or oil changes). PEUGEOT
recommends that you check the level, and top
up if necessary, every 3 000 miles (5 000 km).
After topping up the oil, the check when
switching on the ignition with the oil level
indicator in the instrument panel is not valid
during the 30 minutes after topping up.

222
Checks






Checks













12 V battery


Electrolyte level

For access to the battery, refer to the
"12V battery" section.
Refer to the warranty and
maintenance record for details of
the replacement inter vals for these
components.



















Air filter and passenger compartment filter

Replace the oil filter each time the
engine oil is changed.
Refer to the warranty and
maintenance record for details of
the replacement inter val for this
component.














Oil filter

If necessary, top up using distilled water,
removing the battery cap from each cell.
Check the electrolyte level at least
once a month.
When carrying out work on the battery, refer
to "12V battery" section for details of the
precautions to be taken before disconnecting
the battery and following its reconnection.

Unless other wise indicated, check these components in accordance with the warranty and maintenance record and according to your engine.
Other wise, have them checked by a PEUGEOT dealer or a qualified workshop.

The electrolyte level must be between the
"LOWER LEVEL" and "UPPER LEVEL" marks. Depending on the environment (e.g. dusty
atmosphere) and the use of the vehicle
(e.g. city driving), replace them twice as often
if necessary
.
A clogged passenger compartment filter may
have an adverse effect on the per formance
of the air conditioning system and generate
undesirable odours.

261

Level 1


Level 2


Level 3


Comments



Guidance Indicates that a turn should be made to the left or right at the next
junction and the distance to this junction.
Press on it to to display a navigation zoom to the left of the map.
Navigation sub-menu Confi rm Route
Press on it to modify the current navigation criteria. Change Route
Search Nearby
Set Location
Stop Guidance
Voice Guide ADJ
TMC (Traffi c Message
Channel) Press on it to display traffi c information such as traffi c jams,
roadworks, etc.
Type of display and map
orientation "View"
"2D/3D" Indicates North.
Press on it to select the type of screen display and the map orientation
(2D with vehicle direction, 2D with North at the top, auto 2D according
to scale or 3D perspective).
Map scale Indicates the scale of the map displayed.
Press on it to zoom in or out
Information on
the destination /
intermediate destination Indicates the distance and time to the destination or the intermediate
destination.

273
04








Set the filtering and display of TMC messages


TMC messages (Traffi c Message Channel) give information on traffi c and weather conditions, transmitted in real time and received by the
driver in the form of audible announcements and visual messages on the navigation map.

Press on the pull-down secondary menu.
The navigation system suggests a detour route, if dynamic guidance
has been activated by pressing the NAVI MENU
button, then " TMC
".

Select " Confi rm Route
" then " Entire Route
" or
" Remaining Route
" to validate or add to the route.

Select " Change Route
", then " Alternative Route
" or
" Delete Route
" to modify or delete the route.

Select " Search Nearby
", then " POI nearby
" to add a
point of interest to the route.

Select " Stop Guidance
" to suspend navigation
guidance.

Select " Voice Guide ADJ
" to modify the volume for
the voice or adapt the volume to the speed of the
vehicle.

Red and yellow triangle: traffi c information, for example:






Black and blue triangle: general information, for example:
Weather reports
Modifi ed signage
Risk of explosion Traffi c reports
Narrow carriageway
Road closed Wind
Slippery surface
Demonstration Fog
Accident
Danger Parking
Delay
No entry
Snow / ice
Roadworks
Traffi c jam


TRAFFIC

297
03 GENERAL OPERATION













Description of controls - Menus



Setting
:


- switch off the screen,

- adjust the touch beep,

- adjust the time or display it continuously,

- select the guidance voice,

- select the picture quality for the screen and reversing
camera,

- select RDS.


FM
/ MW
/ LW
: select a radio
station from:


- frequency modulation (FM),

- medium wave (MW),

- long wave (LW).


BT Audio
: connect a Bluetooth
(2.0) telephone then play the
music fi les by streaming.

AUX
: connect a portable player
to the Jack auxiliary socket then
play the music fi les.


Phone
: make or receive
telephone calls.

Change from one screen
to the other.

Voice
: use the voice
commands.


USB
/ iPod
®
: connect a
portable player by USB or an
iPod
® , then play the music fi les.

CD
: play the music fi les
through the CD player
(WAV, MP3, WMA, AAC).

305
04

RDS

The Radio Data System (RDS) function on the FM waveband permits:


- automatic retuning to alternative frequencies carrying the same
station while travelling through different regions (if the transmitters
of this station cover the area through which you are travelling),

- temporary tuning to traffi c information announcements,

- display of the name of the station, etc...
Most FM stations use RDS.

These stations transmit non-audible data in addition to their programmes.
The data transmitted in this way allows you access to various
functions, mainly displaying of the name of the station, temporary
tuning to traffi c information announcements or automatic retuning to
alternative frequencies.
RDS allows you to continue listening to the same station
automatically by means of alternative frequencies. However,
alternative frequencies may not be provided throughout the country.
Radio stations do not cover the whole country, which explains the
loss of reception of the station during a journey.
Regional mode

Some stations are organised in a network.
In different regions, they broadcast different or shared programmes
depending on the time of day.
You can follow:


- a regional station only,

- the entire network, with the possibility that you will be listening
to a different programme.




















RDS, AF, REG, TP, PTY

RADIO


RDS alternative frequencies

Your radio automatically checks and selects the best frequency for
the radio station to which it is tuned (if the station broadcasts on
several transmitters or frequencies).
The frequency of a radio station covers approximately 30 miles
(50 km). The change from one frequency to another explains the
loss of reception during a journey.
If the station to which you are listening does not have several
frequencies in the region in which you are currently located, you can
deactivate automatic alternative frequencies.
Traffi c information function

The Traffic Programme (TP) function permits automatic and
temporary switching to an FM station broadcasting traffi c
information.
The radio station or the source that you are listening to at this point
is paused.
Once the traffi c information has ended, the system switches back to
the radio station or the source that you were listening to initially.

Programme types

Some stations offer the option of listening to a themed type of
programme as a priority, selected from the list available below:
NEWS, AFFAIRS, INFOS, SPORT, EDUCATE, DRAMA, CULTURE,
SCIENCE, VARIED, POP M, ROCK M, EASY M, LIGHT M,
CLASSICS, OTHER M, WEATHER, FINANCE, CHILDREN,
SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ,
COUNTRY, NATION M, OLDIES, FOLK M, DOCUMENT.

321
04 RADIO


The "Radio Data System" (RDS) function on the FM waveband
permits:


- access to the display of information, such as the name of the
station, ...

- listening to the same station while travelling through different
regions,

- temporary tuning to traffi c information announcements.
Most FM stations use RDS. These stations transmit non-audible data
in addition to their programmes.
The data transmitted in this way allows you access to various
functions, mainly displaying of the name of the station, automatic
retuning to alternative frequencies or temporary retuning to traffi c
information announcements.
RDS allows you to continue listening to the same station by means
of alternative frequencies that carry the same station. However, in
certain conditions, RDS alternative frequencies may not be provided
throughout the country. Radio stations do not cover the whole country,
which explains the loss of reception of the station during a journey.
"AF" alternative frequencies

Your radio automatically checks and selects the best frequency for
the radio station to which it is tuned (if the station broadcasts on
several transmitters or frequencies).
The frequency of a radio station covers approximately 30 miles
(50 km). The change from one frequency to another explains the
temporary loss of reception during a journey.
If the station to which you are listening does not have several
frequencies in the region in which you are currently located, you can
deactivate alternative frequencies.

Some stations are organised in a network.
In different regions, they broadcast different or shared programmes
depending on the time of day.
You can follow:


- a regional station only,

- the entire network, with the possibility that you will be listening
to a different programme.

REG regional mode

On long distance journeys, when the stored station becomes
weak, the radio searches fi rst for another frequency for the
same station (AF). Then, if this fails, it searches for a frequency
broadcasting the regional programme (REG). If this also fails, the
radio returns to the stored station.



















RDS


Press the MENU
button.

Press the SEL
knob repeatedly to
select the RDS mode: "AF", "REG"
and "TP" then turn the knob to select
the desired value.

329
05

Press the DISP
button for more than
two seconds to activate the ID3 Tag
information. "TAG" appears in the
screen.
Press the DISP
button repeatedly; the
Tag ID3 information appears in the
following order:
ALBUM NAME / TRACK NAME /
ARTIST NAME / NORMAL DISPLAY
MODE.
To deactivate this information, press
the DISP
button again for more than
two seconds.

If the information exceeds
12 characters, press the PAGE
button
to see the rest.
In the absence of MP3 or ID3
Tag information to be displayed,
"NOTITLE" appears in the screen.

On CD-R/RWs, the quality of the playing sound depends on the
encoding software, the burning device and the burning speed used.
Depending on the fl ow chart of the MP3 folders and fi les on the
disc, play may not begin immediately.


MUSIC MEDIA PLAYERS



















Using the auxiliary input (AUX)


The auxiliary socket, JACK or RCA,
permits the connection of portable
equipment (MP3 player...).

Do not connect a single piece of equipment via the USB port and
the JACK socket at the same time.

Connect the portable equipment (MP3 player…) to the JACK
socket or to the RCA-type audio sockets (white and red) using a
suitable cable, not supplied.

Press the MEDIA
button for more
than two seconds.
"AUX" appears in the screen and the
external mode is activated.
Press MEDIA
again to deactivate
the AUX
mode and change to
another mode.

JACK / RCA cable not supplied