key Peugeot 406 C 2002 User Guide

YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information 'battery flat'is
given by an audible signal accompa- nied by a message on the
multiÐfunction display.
To replace the battery, unclip the casing using a coin at the ring(CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Reprogramming the remote control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key from the
ignition. The remote control is nowworking again.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.
Locating your car
To locate your car, if you have locked it, in a car park:  press button A.The courtesy
lights come on and the directionindicators flash for a few seconds.
01-07-2002

YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number of each key. This number is coded on the label attached to the key. If the key is lost, your PEUGEOT dealer can rapidly supply you with new keys. The high frequency remote control is a sensitive system.
Do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle.The remote control cannot operate while the key is in the ignition, even if the ignition is off, except for reprogramming.
However, do not operate the deadlocking system if there is someone inside the vehicle.As a safety measure (when there are children on board), remove the key from the ignition when you leave the vehicle, even for a short time.
Avoid operating the remote control buttons out of range of your vehicle; you run the risk of stopping it from working. It would then be necessary to reprogramme it. When buying a second-hand vehicle:
- check that you have been given the confidential card;
- have the keys memorised by a PEUGEOT dealer to be sure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
01-07-2002

THE ALARM SYSTEM Setting and deactivating the alarm The alarm completes the security
equipment for your vehicle. It offerstwo types of protection. ¥ exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
¥ interior protection: when it is set,
the alarm sounds if the sensors detect a variation in the air move-
ment inside the vehicle (break-ing of a window) or movementinside the vehicle.
The alarm is also equipped with ananti-tamper function. If an attempt is made to tamper with the wires to the siren, control unit or
the battery, the alarm is triggered:the siren sounds and the headlampscome on. Setting the alarm (interior and exterior protection) Switch the ignition off and get out of the vehicle. Press the locking button of the
remote control key. The doors lock.The direction indicators light for two seconds. The red light on the switch flashes once a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set. Note:
when the alarm is triggered,
the siren sounds for thirty seconds. After the thirty seconds it stops, butthe alarm remains set.
Warning: If, on setting the alarm, a
door, the boot or the bonnet are not
closed correctly, the siren sounds fora moment. If the vehicle is closedcorrectly in the following 45 seconds,the alarm is set and the directionindicators remain on for twoseconds. In all cases, the alarm isset after 45 seconds. Disarming the alarm (interior and exteriorl protection) Press the unlocking button of the
remote control key. The doors unlock.The direction indicators flash for two seconds. The red warning light on the switch goes out. Note:
if the warning light continues
to flash after disarming the alarm, it is a sign that the alarm has been trig-
gered. The flashing will stop whenthe ignition is switched on.
SPECIAL FEATURES 135
01-07-2002

Emergency cut-off (If the remote control is not work- ing)
Unlock the doors with the key.
Open the door.
The alarm is triggered. You have ten
seconds in which to switch it off. ¥ Switch on the ignition.
¥ Immediately press interior protec-tion button 1.
¥ The siren stops and the alarm is disarmed. Selecting the type of protectionLocking without setting the alarm Special precautions
To set the alarm with exterior
protection only. If, while you are away from the vehi- cle, you wish to leave a window par-tially open or a pet inside the vehicle,you need to select exterior protectiononly:
¥ Switch off the ignition.¥ Within the next ten seconds, press
the interior protection button 1until
the light comes on continuously.
¥ Get out of the vehicle.¥ Press the locking button of the remote control.
¥ The doors lock.
¥ The direction indicators come on for two seconds.
¥ The red light on the switch flashes once a second.
To disarm exterior protection only
Press the unlocking button on the remote control. The doors unlock and the courtesy lights come on. The direction indicators flash for two seconds. The red light on the switch goes out. To lock the vehicle without setting the alarm It is the remote control which sets the alarm. Therefore, to lock the vehicle with-
out setting the alarm: use the key.
To recharge or replace the battery: ¥ Switch on the ignition.¥
You have 10 seconds after switching
on the ignition to press the interior protection button 1and hold it down
for two seconds.
¥ The indicator light flashes rapidly for three seconds.
¥
You can now disconnect the battery.
After reconnecting the battery:
¥ Lock, then unlock the vehicle using the remote control.
The alarm will be set the next time the vehicle is locked.
SPECIAL FEATURES
136
Do not make any modi- fications to the alarmsystem.
01-07-2002

BOOT Simultaneous locking or unlock- ing of the boot and the doors
Turn the key a quarter turn from Ato
B .
The boot is then controlled by the remote control or the driver's doorlock. Locking the boot only
Turn the key a quarter of a turn from A to C. The boot is then locked,
whatever the action of the remotecontrol or the driver's door lock.
To return to simultaneous operation with the doors: turn the key from Ato
B .
YOUR 406 COUPE IN DETAIL
88
OPENING THE BONNET From inside:
pull the handle on the
left-hand side under the fascia.From outside: lift the catch and
raise the bonnet. Bonnet struts These open the bonnet and hold it open.
To close Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. FILLING WITH FUEL Fill with fuel with the engine switched
off.
To open the fuel filler flap, firmly pull the handle on the floor on the outsideof the driver's seat. If you are filling up your tank, do not
continue after the 3rd cut-off of thepump; this could cause your vehicleto malfunction. The capacity of the tank is approx- imately 15.4 gallons (70 litres).
A filler cap hook is provided on the inside of the fuel filler flap.
01-07-2002

AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
 Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by:
- manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories position (first notch),
 press the end of the lights stalk formore than two seconds,
 place the lights stalk in the 0posi-
tion,
 flash the headlamps,
 get out of the car and lock it.
YOUR 406 COUPE IN DETAIL
100
01-07-2002

Sun visor with illuminated courtesy mirror With the ignition on, the mirror is automatically lit up when the flap isopened.
YOUR 406 COUPE IN DETAIL119
COURTESY LIGHTS Off. On when one of the doors is opened. Permanently on when the ignition key is in the accessories position or the ignition is on.
1 - Front courtesy light.
2 - Rear courtesy light.
3 - Map-reading lights. With the key in the accessories position or the ignition on, operate the rele- vant switch. Coat hook Press the lower section to extract the hook from its housing.
01-07-2002

DRIVING YOUR 406 COUPE127
Operating check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multi-function dis-
play. With the ignition on (2nd notch), illu- mination of this warning light accom-panied by an audible signal and themessage "Passenger air bag dis-
armed" on the multi-function display,
indicates that the passenger air bagis disarmed (slot in the "OFF" posi-
tion).
Disarming the passenger air bag*
To ensure the safety of your child, it is essential to disarm the pas-senger air bag when you install arear-facing child seat on the frontpassenger seat. 
With the ignition switched off, insert the key into the passengerair bag disarming slot 1, turn it to
the "OFF" position, then remove
it keeping the slot in this position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the"ON" position to re-activate the air
bag and thus ensure the safety ofyour passenger in the event of animpact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the multi-
function display.
If this indicator light comeson, accompanied by anaudible signal and the mes-sage "Air bag fault" on the
multi-function display, con-
tact a PEUGEOT dealer to have thesystem checked.
01-07-2002

DRIVING YOUR 406 COUPE127
Operating check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multi-function dis-
play. With the ignition on (2nd notch), illu- mination of this warning light accom-panied by an audible signal and themessage "Passenger air bag dis-
armed" on the multi-function display,
indicates that the passenger air bagis disarmed (slot in the "OFF" posi-
tion).
Disarming the passenger air bag*
To ensure the safety of your child, it is essential to disarm the pas-senger air bag when you install arear-facing child seat on the frontpassenger seat. 
With the ignition switched off, insert the key into the passengerair bag disarming slot 1, turn it to
the "OFF" position, then remove
it keeping the slot in this position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the"ON" position to re-activate the air
bag and thus ensure the safety ofyour passenger in the event of animpact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the multi-
function display.
If this indicator light comeson, accompanied by anaudible signal and the mes-sage "Air bag fault" on the
multi-function display, con-
tact a PEUGEOT dealer to have thesystem checked.
01-07-2002

CHECKING THE LEVELS Engine Checking the oil levelCheck the level regularly and top up between changes. Maximumconsumption is 0.5 litres per 600miles (1 000 km). The oil level should be checked with the vehicle level and the engine cold.There are two marks onthe dipstick: A= maximum
B = minimum
Oil change: according to the manu-
facturer's servicing schedule.
- Dipstick. Never fill past the maxi- mum mark A.
- Oil level gauge on the instrument panel.
Viscosity selection In all cases, the oil selected must meet the manufacturer's require-ments. Oil filter Change the filter regularly according to the servicing schedule. Used oilPrevent used oil from coming into prolonged contact with the skin. Do not dispose of used oil into drains or onto the ground.
To maintain the reliability of engines and emission control systems, theuse of additives in the engine oil isprohibited.
Brakes and clutch Checking the brake and clutch fluid level:
- The level should always be above the DANGER mark on the reser-
voir.
- If the level drops substantially, contact a PEUGEOT dealer imme-
diately.
Fluid change
- must be carried out according to the manufacturer's servicing sche- dule.
- use fluids approved by the manu- facturer, which fulfil DOT 4 stan-dards. Cooling system Use the fluid approved by the manu-
facturer. When the engine is warm, the tem- perature of the coolant is controlledby the engine fan. Because this fancan operate with the ignition keyremoved and because the coolingsystem is pressurised, wait for atleast one hour after the engine hasstopped before carrying out anywork. In the event of a breakdown and to avoid any risk of burns, slacken thecap to the first notch to release thepressure. When the pressure hasdropped, remove the cap and top upthe level.
MAINTENANCE OF YOUR 406 COUPE
30
01-07-2002