battery Peugeot 406 C 2002 Owner's Manual

MAINTENANCE OF YOUR 406 COUPE23

All driving conditions. oArduous conditions.
A AND C SERVICES AND THE INTERMEDIATE VISIT
- Oil filter- Fuel filter(Petrol)- Fuel filter element (diesel only).- Air filter element- Spark plugs (petrol only)
- Engine oil- Bleed fuel filter (diesel only)
- Engine oil (check + top-up)- Gearbox oil (check + top-up)- Battery (check + top-up)- Front/rear screen wash (check + top-up )- Coolant (check + top-up)- Brake fluid (check + top-up)- Power steering fluid (check + top-up according to specification)- Operation of lights and indicators- Condition of glass, headlamp & light lenses and mirrors- Horn- Windscreen washer jets- Condition of wiper blades- Condition and tension of the ancillary drive belts- Handbrake- Condition of hydraulic circuits (hoses and covers)- Condition of rubber boots and gaiters- Brake pads o- Play in hubs, link rods, ball joints, flexible mountings- Shock absorbers- Rear drum brake lining wear- Condition and pressure of tyres (including spare wheel)- Emission control check according to current legislation (petrol only)- Smoke opacity (diesel only) - Pollen filter (according to specification)o- Visual check of the whole vehicle by a Peugeot technician
DRAIN and REFILL
REPLACE
LEVELS
CHECK

ROAD TEST
- Courtesy vehicle
SERVICE
LevelOperation Description of Operation First Service
A C Intermediate
01-07-2002

1 -Fuel filler cap warning light.
2 - Door open warning light.
3 - Dipped beam headlamps indicator light.
4 - Main beam headlamps indicator light.
5 - Rev. counter.
6 - Left-hand direction indicator.
7 - Central (STOP) warning light.
8 - Low fuel level warning light.
9 - Fuel gauge. 10 -
Service indicator, oil level indica-
tor and total distance recorder.
11 - Right-hand direction indicator.
12 - Speedometer.
13 - Clogging of the particulateemission filter warning light(Diesel).
14 - Front fog lamps indicator light.
15 - Rear fog lamp indicator light.
16 - Dynamic stability control(ASR/ESP) warning light (petrolversions only). 17 -
Low coolant level warning light.
18 - Coolant temperature indicator.
19 - Trip recorder zero reset button.
20 - Handbrake and low brake fluid level warning light.
21 - Seat belt not fastened warninglight.
22 - Air bags warning light.
23 - ABS system warning light.
24 - Engine diagnostics warninglight.
25 - Battery charge warning light.
26 - Diesel engine preheating indicator light.
27 - Passenger air bag disarmingwarning light.
28 - Water in diesel filter warninglight.
29 - Front brake pad wear warninglight.
30 - Engine oil pressure warninglight.
31 - Electronic immobiliser warninglight.
32 - Lighting rheostat.
33 - Engine oil temperature indicator.
YOUR 406 COUPE IN DETAIL
102
INSTRUMENT PANEL DIALS: PETROL / DIESEL
01-07-2002

YOUR 406 COUPE IN DETAIL103
1 -
Fuel filler cap warning light.
2 - Door open warning light.
3 - Dipped beam headlamps indi- cator light.
4 - Main beam headlamps indicatorlight.
5 - Rev. counter.
6 - Left-hand direction indicator.
7 - Central (STOP) warning light.
8 - Low fuel level warning light.
9 - Fuel gauge. 10 -
Service indicator, oil level indicator and total distance
recorder.
11 - Right-hand direction indicator.
12 - Speedometer.
13 - Front fog lamps indicator light.
14 - Rear fog lamp indicator light.
15 - Dynamic Stability Control(ASR/ESP) warning light.
16 - Low coolant level warning light. 17 -
Coolant temperature indicator.
18 - Trip recorder zero reset button.
19 - Handbrake and low brake fluid level warning light.
20 - Seat belt not fastened warninglight.
21 - Air bags warning light.
22 - ABS system warning light.
23 - Engine diagnostics warninglight.
24 - Battery charge warning light.
25 - Passenger air bag disarmingwarning light.
26 - Front brake pad wear warninglight.
27 - Engine oil pressure warninglight.
28 - Operating programmes.
29 - Gear lever position indicator.
30 - Electronic immobiliser warninglight.
31 - Lighting rheostat.
32 - Engine oil temperature indicator.
INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX
01-07-2002

YOUR 406 COUPE IN DETAIL
106
Passenger air bag disarming warninglight Illumination of this warning
light is accompanied by an audible signal and a message on the multi-
function display. If the passenger airbag is disarmed, the indicator lightcomes on when the ignition isswitched on and remains on. In all cases, if the warning light flash-
es, contact a PEUGEOT dealer.
Air bag warning light The warning light comes on for 6 seconds when theignition is switched on.
Illumination of this warning light, withthe engine running, is accompaniedby an audible signal and a messageon the multi-function display indicat-ing the cause of the front, side or curtain air bag fault.
Contact a PEUGEOT dealer.
Water in diesel filter warning light (according to destination)
Contact a PEUGEOT dealer as soon as possible.
There is a risk of damage to the injection system. Diesel pre-heating indicator lightIf the engine is warm enough, the light will not come on and you can start the engine without waiting.
If the light comes on, wait until it goes out before trying the starter. Engine diagnostics warning light This comes on each time the ignition is switched on. If it is lit continuously with the engine runnning, this indicates a fault in the emission control system.
If it flashes with the engine running, this indicates a malfunction in the injection
or ignition system. There is a risk of damage to the catalytic converter (petrolengine only).
Contact a PEUGEOT dealer as soon as possible. Battery charge warning light This comes on each time the ignition is switched on.If it comes on with the engine running it can indicate:
Ðfaulty operation of the charging circuit,
Ðloose battery or starter terminals,
Ða cut or slack alternator belt,
Ðan alternator fault.
Contact a PEUGEOT dealer.
01-07-2002

This enables the following information to be displayed:
- the time,
- the date,
- the outside temperature (the ¡C symbol flashes when there is a risk of ice),
- the radio displays,
- the status of the doors. The display shows you whether a door, the boot or thebonnet is open and if the fuel filler cap is missing.
- the warning messages (e.g. ''battery low'') or information messages (e.g. "top up fuel tank''), displayed temporarily, can be cleared by pressing button 1or
2 ,
- the trip computer. Setting the parameters Press button 1for two seconds to access the settings. The information flashes
to show it is ready to be modified.Then, individual presses on button 1 allow you to scroll through the various data
in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (Celsius or Fahrenheit),
- time format (12 then 24 hour mode)
- hour,
- minutes,
- year,
- month,
- day, Pressing button 2allows you to change the information selected. Maintain the
pressure for rapid scrolling.After ten seconds without action, the display returns to the main screen and the modified data are recorded.Display B
YOUR 406 COUPE IN DETAIL 111
01-07-2002

YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information 'battery flat'is
given by an audible signal accompa- nied by a message on the
multiÐfunction display.
To replace the battery, unclip the casing using a coin at the ring(CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Reprogramming the remote control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key from the
ignition. The remote control is nowworking again.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.
Locating your car
To locate your car, if you have locked it, in a car park:  press button A.The courtesy
lights come on and the directionindicators flash for a few seconds.
01-07-2002

THE ALARM SYSTEM Setting and deactivating the alarm The alarm completes the security
equipment for your vehicle. It offerstwo types of protection. ¥ exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
¥ interior protection: when it is set,
the alarm sounds if the sensors detect a variation in the air move-
ment inside the vehicle (break-ing of a window) or movementinside the vehicle.
The alarm is also equipped with ananti-tamper function. If an attempt is made to tamper with the wires to the siren, control unit or
the battery, the alarm is triggered:the siren sounds and the headlampscome on. Setting the alarm (interior and exterior protection) Switch the ignition off and get out of the vehicle. Press the locking button of the
remote control key. The doors lock.The direction indicators light for two seconds. The red light on the switch flashes once a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set. Note:
when the alarm is triggered,
the siren sounds for thirty seconds. After the thirty seconds it stops, butthe alarm remains set.
Warning: If, on setting the alarm, a
door, the boot or the bonnet are not
closed correctly, the siren sounds fora moment. If the vehicle is closedcorrectly in the following 45 seconds,the alarm is set and the directionindicators remain on for twoseconds. In all cases, the alarm isset after 45 seconds. Disarming the alarm (interior and exteriorl protection) Press the unlocking button of the
remote control key. The doors unlock.The direction indicators flash for two seconds. The red warning light on the switch goes out. Note:
if the warning light continues
to flash after disarming the alarm, it is a sign that the alarm has been trig-
gered. The flashing will stop whenthe ignition is switched on.
SPECIAL FEATURES 135
01-07-2002

Emergency cut-off (If the remote control is not work- ing)
Unlock the doors with the key.
Open the door.
The alarm is triggered. You have ten
seconds in which to switch it off. ¥ Switch on the ignition.
¥ Immediately press interior protec-tion button 1.
¥ The siren stops and the alarm is disarmed. Selecting the type of protectionLocking without setting the alarm Special precautions
To set the alarm with exterior
protection only. If, while you are away from the vehi- cle, you wish to leave a window par-tially open or a pet inside the vehicle,you need to select exterior protectiononly:
¥ Switch off the ignition.¥ Within the next ten seconds, press
the interior protection button 1until
the light comes on continuously.
¥ Get out of the vehicle.¥ Press the locking button of the remote control.
¥ The doors lock.
¥ The direction indicators come on for two seconds.
¥ The red light on the switch flashes once a second.
To disarm exterior protection only
Press the unlocking button on the remote control. The doors unlock and the courtesy lights come on. The direction indicators flash for two seconds. The red light on the switch goes out. To lock the vehicle without setting the alarm It is the remote control which sets the alarm. Therefore, to lock the vehicle with-
out setting the alarm: use the key.
To recharge or replace the battery: ¥ Switch on the ignition.¥
You have 10 seconds after switching
on the ignition to press the interior protection button 1and hold it down
for two seconds.
¥ The indicator light flashes rapidly for three seconds.
¥
You can now disconnect the battery.
After reconnecting the battery:
¥ Lock, then unlock the vehicle using the remote control.
The alarm will be set the next time the vehicle is locked.
SPECIAL FEATURES
136
Do not make any modi- fications to the alarmsystem.
01-07-2002

THE DOORS Opening the doors from outsideOpening the doors from insideLocking from the inside
To lock, press button
A.
Locking the front doors locks the front doors and the boot.
YOUR 406 COUPE IN DETAIL 87
To make opening of the door easier, the window automatically lowers by a few centimetres. It rises and automatically adjusts itself on closing the door to ensure perfect sealing.
Before carrying out any work which involves disconnection of the bat-
tery, lower the windows to permit opening and closing of the doors.
Warning: If the battery is disconnected, the doors can still be opened. How-
ever, it is imperative that the door is not slammed on closing. Consult your PEUGEOT dealer as soon as possible. SUNROOF
¥ To tilt
Press part Aof the switch. To
close, press part Bof the switch
until the sunroof is completely closed.
¥ To open Press part Bof the switch. To
close, press part Aof the switch
until the sunroof is completelyclosed.
01-07-2002

Moving Off
With the engine running, to move off from position P:
It is essential to press the brake pedal to exit position P (shift
lock),
Select the required position ( R, D ,
3 , 2 or 1) then gradually release
the brake pedal: the vehicle
moves off immediately.
You can also move off from positionN :
Release the handbrake with your foot on the brake pedal,
Select the required position ( R, D ,
3 , 2 or 1) then gradually release
the brake pedal: the vehicle
moves off immediately. Automatic Operation Automatic changing of the
four
gears :
Move the selector lever to position D.
The gearbox continuously selectsthe most suitable gear according tothe following parameters:
Ðdriving style,
Ðroad characteristics,
Ðvehicle load.
The gearbox functions in autoadaptive mode without any
action on your part. When the engine is idling
with position
R, D, 3, 2or
1 selected and the brakes
off, the car will move even
without you accelerating. For this reason, do not leave
children unsupervised inside the vehicle when the engine isrunning. If work needs to be done with the engine running, apply thehandbrake and select position P
.
Never select position Nwhen the
vehicle is moving. Never select position Por R
unless the vehicle is stationary .
Do not change from one position to another to optimise braking onslippery roads. In the event of battery failure, if the lever is in position Pit will not
be possible to change to anotherposition.
122
DRIVING YOUR 406 COUPE
Note: For immediate maximum acceleration
without touching the gear lever, pressthe accelerator pedal down as far as it
will go (kickdown). The gearbox willchange down automatically or stay inthe gear selected, up to maximumengine speed. When braking, the gearbox changes down automatically to provide
efficient engine braking.
If you take your foot off the
accelerator suddenly, the gearboxwill not change up for reasons of
safety.
01-07-2002