display Peugeot 406 C 2004 Owner's Guide

02-02-2004
YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information
"battery flat"is
given by an audible signal accompa- nied by a message on the multi-func-
tion display.
To replace the battery, unclip the
casing using a coin at the ring(CR 2016/3 volt battery).If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary. Keep your card in a safe place, never inside the vehicle.
Programming the remote con- trol
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately for a
few seconds.
 Switch off the ignition and remove the remote control key from the
ignition lock. The remote controlis now working again.
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the code is recognised and starting ispossible. If the system does not function correctly
, contact a PEUGEOT
dealer as soon as possible.

02-02-2004
AUTOMATIC SWITCHING ON OF THE LIGHTS The side lights and dipped beam headlamps switch on automatically if
the light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
 Press the end of the lights stalkfor more than two seconds.
Note: in foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located on the windscreen behind
the mirror. It is used for automat-ic switching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Manual operation of the lights
stalk always takes priority Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multi-function display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is howeverpossible to disarm this function and
switch off the lights by:
Ð manually switching off the lights using the lights stalk,
Ð switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights come
on). The driver is alerted by theflashing of the ''dipped beam'' warn-ing light on the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute. This function can only be used if the automatic switching on of the lightsmode is activated then:  with the key in the accessories position (1st notch), flash theheadlamps,
 get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103

02-02-2004
WINDSCREEN WIPER STALK Front windscreen wipers2 Rapid wipe (heavy rain)
1 Normal wipe (moderate rain).
AUTO Automatic wipe.
0 Off.


Single wipe (press downwards). Operation In position
1or 2, when the vehicle
stops, the windscreen wiper changes to a lower wiping speed, thenresumes its initial speed when thevehicle starts again. When the ignition has been switched off for more than a
minute with the stalk in the AUTOposition, it is necesary to reacti-vate this function. To do this, move
the stalk to any position, then move itback to the AUTOposition.
Automatic wipe In the AUTO position, the wiper oper-
ates automatically and adjusts its
speed to the intensity of the rainfall. Operating check ActivationActivation of the function is accom- panied by the message "Automatic
wiper activated" on the multi-func-
tion display. In the event of malfunction in the
AUTO position, the windscreen
wiper will operate in down-grade mode. Have the system checked by a
PEUGEOT dealer.
YOUR 406 COUPE IN DETAIL
104
Do not cover the rain detector located on thewindscreen behind the
interior mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.
Windscreen and headlamp wash Pull the windscreen wiper stalk
towards you. The windscreen washthen the windscreen wipers operatefor a fixed period. The windscreen wash and headlamp wash operate simultaneously for twoseconds, only if the headlamps are
on.

02-02-2004
TRIP COMPUTERDisplay B Display C
Ð the range
Ð the distance travelled
Ð the average consumption
Ð the current consumption
Ð the average speed Zero reset Press the stalk for more than two seconds. Pressing the button on the end of the
wash/wipe stalkenables the following data to
be displayed:
Ð the current consumption and the range,
Ð the average consumption, the distance travelled and theaverage speed calculated over a period "1",
Ð the average consumption, the distance travelled and the average speed calculated over a period "2".
Periods "1"and "2"are defined by the frequency of the zero
reset. They allow, for instance, daily calculations over period "1" and monthly calculations over period "2".
Zero reset When the required period is displayed, press the stalk for more than two seconds.
YOUR 406 COUPE IN DETAIL
116

02-02-2004
Range The display shows the distance that can still be covered with the fuelremaining in the tank. Note:this figure may rise if there is a
change in driving style or road sur- face, causing a significant drop incurrent fuel consumption. If there are less than 3 litres of fuel in the tank, only three segments will bedisplayed. Average consumption This is the ratio between the amount of fuel consumed and the distancetravelled since the computer was lastreset to zero.
Current fuel consumption This gives the fuel consumption recorded during the last two sec-
onds. This function is only displayedwhen the vehicle is travelling at morethan 12 m.p.h. (20 km/h). Average speed This is obtained by dividing the dis- tance travelled by the period of timethe vehicle has been in use (with theignition on), since the computer waslast reset to zero.Distance travelled This shows the distance travelled since the computer was last reset tozero. After the trip computer has been reset to zero, the range databecomes meaningful only after thevehicle has been in use for a certainperiod. If horizontal segments are displayed instead of figures when driving, con-
tact a PEUGEOT dealer.
YOUR 406 COUPE IN DETAIL
117

124DRIVING YOUR 406 COUPE
AUTOMATIC AUTOADAPTIVE GEARBOX The 4-speed automaticgearbox offers the comfort of integral automatic operation ,
enhanced by a sportprogramme (switch A) and a snowprogramme (switch B).
Gear selection gate  Move the lever in the gate to select one of the positions.Once the position is selected, the indicator light for that position illuminates on
the instrument panel display.
P. Park: for immobilising the vehicle and for startingthe engine, with the hand-
brake on or off. R. Reverse: this must be engaged when the vehicle is stationary and the engine
at idle.N. Neutral: for startingthe engine and for parking, with the handbrake on.
D. Drive: for driving in autoadaptive mode (automatic changing of the four
gears).3. For driving in townor on winding roads (automatic changing of the first three
gears only).
2. For driving in the mountainsor for towing a trailer (automatic changing of
the first two gears only).
1. For use on steep gradients (selection of first gear only).
Special feature of the gearbox (2 litre petrol engine)Selection of first gear is by pressing button Cwith the lever in position 2.
To exit first gear, press button Cagain or move the selector lever.
V6 engine 2 litre engine
02-02-2004

02-02-2004
DRIVING YOUR 406 COUPE
128
THE HANDBRAKE
To apply When parking on a slope, turn the wheels towards the kerb and applythe handbrake.
To release Pull the handle and press the button to release the handbrake and movethe vehicle.
Disarming the ESP/ASR systems In certain exceptional conditions
(vehicle stuck in mud or snow, or onloose ground...), it could prove useful
to disarm the ASR and ESP systemsto make the wheels spin and regaingrip. 
Press the switch "ESP OFF", sit-
uated to the left of the steering wheel.
The switch lights up and the indicatorlights come on, accompanied by themessage '' ASR/ESP de-activated''
on the multi-function display: the
ESP and ASR systems no longer
affect the operation of the engine orthe brakes. They engage again: automatically when the ignition is
switched off,
 manually by pressing the switchagain. The ASR/ESP systemsoffer increased safety dur-ing normal driving, butshould not incite the driver
to take risks or to drive at highspeed. The operation of these systems is assured on condition that therecommendations of the manufac-turer regarding the wheels (tyresand wheel rims), the braking com-ponents, the electronic compo-nents and the assembly andrepair procedures within thePEUGEOT network are respected. After an accident or impact, have the system checked by a
PEUGEOT dealer.
Operating check When a system malfunctionoccurs, the switch lightflashes and the indicatorlight comes on.
Contact a PEUGEOT dealer tocheck the system.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP) These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, by act-ing on the brakes of the drive wheelsand on the engine. It also allows thedirectional stability of the vehicle tobe improved on acceleration. If there is a variation between the tra- jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course.
Operation of the ASR and ESP systems
The warning light flashes if
the ASR or ESP is activated.

02-02-2004
DRIVING YOUR 406 COUPE129
AIR BAGS
The air bags have been designed to maximise the safety of the occupantsin the event of serious collisions.They work in conjunction with the
force-limiting seat belts. The elec-tronic detectors register and analyseany abrupt deceleration of the vehi-cle: if the triggering threshold isreached, the air bags inflate instantlyand protect the occupants of thevehicle. Immediately after the impact, the air bags deflate rapidly so that they donot hinder the visibility of the occu-pants nor their exit if necessary fromthe vehicle. The air bags are not deployed in the case of collisions which are not seri-
ous, for which the seat belt is suffi-cient to ensure maximum protection.The seriousness of a collisiondepends on the nature of the obsta-cle and the speed of the vehicle atthe moment of the collision. Air bags only operate when the ignition is switched on. Note:
the gas escaping from the air
bags can be a minor irritant. FRONT AIR BAGSThese are folded in the centre of the steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,except in cases where the passen-ger air bag is disarmed.
Front air bag fault If this warning light comes on, accompanied by anaudible signal and the mes-
sage "Air bag fault" on the
multi-function display, contact a
PEUGEOT dealer to have the sys-tem checked. Passenger air bag precautions For a vehicle fitted with a passenger air bag disarming switch:
Ð disarm the airbag if you installa rear-facingchild seat on thefront passengerseat,
Ð arm the air bag for an adult pas-
senger.
For a vehicle not fitted with a pas-senger air bag disarming switch: Ð do not install a rear-fac-ing child seat on thefront passenger seat.
Never place your feet or any objecton the fascia.

DRIVING YOUR 406 COUPE
130
Disarming check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multifunction dis-
play. With the ignition on (2nd notch), illumination of this warning lightaccompanied by an audible signaland the message "Passenger
air bag deactivated" on the
multifunction display, indicates thatthe passenger air bag is disarmed(switch in the "OFF"position).
Disarming the passenger air bag*
To ensure the safety of your child, it is essential to disarm the pas-senger air bag when you install arear-facing child seat on the frontpassenger seat. Otherwise, the child would risk being killed or seriously injured ifthe air bag were to inflate. 
With the ignition switched off ,
insert the key into the passenger air bag disarming switch 1, turn it to the
"OFF" position, then remove the
key keeping the slot in this position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the "ON" position
to re-activate the air bag and thusensure the safety of your passenger inthe event of an impact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the multi-
function display.
If this indicator light comeson, accompanied by anaudible signal and themessage "Air bag fault"
on the multi-function dis-
play, contact a PEUGEOT dealer tohave the system checked.
02-02-2004

DRIVING YOUR 406 COUPE
130
Disarming check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multifunction dis-
play. With the ignition on (2nd notch), illumination of this warning lightaccompanied by an audible signaland the message "Passenger
air bag deactivated" on the
multifunction display, indicates thatthe passenger air bag is disarmed(switch in the "OFF"position).
Disarming the passenger air bag*
To ensure the safety of your child, it is essential to disarm the pas-senger air bag when you install arear-facing child seat on the frontpassenger seat. Otherwise, the child would risk being killed or seriously injured ifthe air bag were to inflate. 
With the ignition switched off ,
insert the key into the passenger air bag disarming switch 1, turn it to the
"OFF" position, then remove the
key keeping the slot in this position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the "ON" position
to re-activate the air bag and thusensure the safety of your passenger inthe event of an impact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the multi-
function display.
If this indicator light comeson, accompanied by anaudible signal and themessage "Air bag fault"
on the multi-function dis-
play, contact a PEUGEOT dealer tohave the system checked.
02-02-2004