anti Peugeot 406 C 2004 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2004, Model line: 406 C, Model: Peugeot 406 C 2004Pages: 141, PDF Size: 1.8 MB
Page 24 of 141
02-02-2004
25
MAINTENANCE OF YOUR 406 COUPE
Recommendations for approved lubricants
The oils which appear in the table oppo-site are suitable for most purposes. The diagram opposite states the opti- mum range of viscosity depending on thetemperatures at which the oils are to beused. It is also possible to use synthetic oils of "superior quality". In the absence of semi-synthetic or syn-
thetic oils, oils of ACEA A1/A2 and API
SH/SJ/SL quality (for petrol engines), or
ACEA B1/B2 and API CD/CF quality (fordiesel engines) may be used by followingthe 'Arduous Conditions' servicingschedule, which specifies shorter serviceintervals. Do not hesitate to ask for advice from a
PEUGEOT dealer to maintain drivingpleasure and to minimise the mainte-nance cost of your vehicle. For countries outside Europe, please
contact a local PEUGEOT dealer.
ONLY ONLY
Manual Gearbox ESSO GEAR OIL BV TOTAL TRANSMISSION BV 75W-80 PR 9736.41 75W-80 PR 9730.A2
ONLY
Automatic Gearbox PR 9736.22 ESSO ATF 4HP20-AL4
Power steering ESSO ATF D TOTAL FLUIDE AT42 PR 9730.94 PR 9730.A3
Power steering FLUIDE DA PR 9730.A1*
Brake circuit PEUGEOT DOT4 Cooling circuit
PROCOR TM108/GLYSANTIN G33 or REVKOGEL 2000 ONLYProtection to minus 35 degrees Celsius
* Only for extremely cold countries. Other recommended products
Page 28 of 141
YOUR 406 COUPE IN DETAIL
108
Handbrake, low brake fluid level and electronic brake force distribution warning light. This comes on each time the ignition is switched on.
It indicates either:
Ð that the handbrake is on or has not been released correctly,
and when coupled with the central (STOP) warning light:
Ð an excessive drop in the brake fluid level (if the light remains on even with the handbrake released),
Ð lit at the same time as the ABS warning light, it indicates a malfunction of the electronic brake force distribution system.
Stop immediately.
Contact a PEUGEOT dealer.
Anti-lock braking system (ABS) warning light This comes on for 3 seconds each time the ignition is switched on.If it comes on at over 8 m.p.h. (12 km/h), it indicates a malfunction of the ABS.
However, the vehicle retains conventional servo-assisted braking.
Contact a PEUGEOT dealer.
Clogging of the particu- late emission filter warn-ing light (diesel engine) Display of this warning light
is accompanied by an audible signal.The flashing of this light while the engine is running is caused either bythe particulate emission filter beingoverloaded or by the engine runningtoo long at idle (white smoke from
the exhaust). There is a risk of the fil-ter clogging if the same conditions ofoperation are maintained. As soon as possible, drive for at least three minutes at a speedexceeding 37 m.p.h. (60 km/h),where driving conditions allow this. If the light comes on, contact a
PEUGEOT dealer as soon as possible. Front brake pad wear warning light
For your safety, have the pads replaced as soon as this light comes on.
ASR/ESP Electronic Stability Programmeindicator light This comes on for a few
seconds each time the ignition is switched on. If the indicator light stays on or comes on while the engine is run-
ning: contact a PEUGEOT dealer. When the engine is running and the vehicle is moving, it flashes if thesystem is activated. It is lit continuously when it is dis- armed.
02-02-2004
Page 35 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL
52
Stalk movement Function
1
-Press (behind) Increase volume.
2 -Press (behind) Decrease volume.
1 + 2 -Simultaneous press Cutting off of the sound (mute); restoring of the sound by pressing any button.
3 -Press Automatic search of upper frequencies (radio) -
Selection of the following track (CD).
4 -Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5 -Press the end Change of source (radio/cassette/CD changer).
6 -Rotation Selection of next memorised station (radio) -
(clockwise) Selection of following CD.
7-Rotation Selection of previous memorised station (radio) -
(anti-clockwise) Selection of previous CD.
AUDIO RM2
Page 37 of 141
02-02-2004
GENERAL FUNCTIONS On/offWith the ignition key in the ACCESSORIES or IGNITION position, press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ignition being switched on.
Anti-theft systemThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Turn button Ato increase or decrease the volume.
AUDIO SETTINGS Press the "AUDIO"button several times in succession to access the bass (BASS), treble(TREB) , loudness
(LOUD) , fader(FAD), balance (BAL)and the automatic volume correction.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing the "AUDIO" button after configuration of the automatic volume correction.
Note: bass and treble settings are specific to each source. It is possible to set them differently for radio,
cassette and CD changer.
YOUR 406 COUPE IN DETAIL
54
Page 45 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL
62
Stalk movement Function
1- Press (behind) Increase volume.
2- Press (behind) Decrease volume.
1 + 2 -Simultaneous pressCutting off of the sound (mute); restoring of the sound by pressing any button.
3- Press Automatic search of upper frequencies (radio) -
Selection of the following track (CD).
4- Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5- Press the end Change of source (radio/CD changer).
6- Rotation Selection of next memorised station (radio) -
(clockwise) Selection of following CD.
7- Rotation Selection of previous memorised station (radio) -
(anti-clockwise) Selection of previous CD.
AUDIO RD3
Page 47 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL
64
GENERAL FUNCTIONS On/off With the ignition key in the ACCESSORIES or IGNITION position, press button Ato switch the set on or
off.The set can operate for 30 minutes without the vehicle ignition being switched on.
ANTI-THEFT SYSTEMThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Turn button Ato increase or decrease the volume of the set.
Note: If you have a telephone fitted with a "mute"signal output connected to the set, the set will automatically
change to "mute"when the telephone is used.
AUDIO SETTINGS Press the "AUDIO"button several times in succession to access the bass (BASS), treble (TREB) , loudness
(LOUD) , fader (FAD), balance (BAL)and the automatic volume correction.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing the "AUDIO" button after configuration of the automatic volume correction.
Note: the bass and treble settings are specific to each source. It is possible to set them differently for radio,
CD, or CD changer.
Page 86 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL87
THE ALARM SYSTEM*
This offers two types of protection: ¥
external , it sounds if a door, the
bonnet or the boot is opened.
¥ internal , it sounds if there is air
movement in the passenger com- partment (a broken window ormovement inside the vehicle).
Note: it also has an anti-tamper
function; if there is an attempt to tam-per with the wires to the siren, the
control unit or the battery, the sirensounds and the direction indicatorslight. Setting
Switch the ignition off and get out of the vehicle. Set the alarm within five minutes fol- lowing your exit from the vehicle bylocking using the remote control (thered light on the switch, visible fromthe outside, flashes every secondand the direction indicators come onpermanently for two seconds).
5 seconds later, internal protection is set.
45 seconds later, external protection is set. When the alarm is triggered, the siren sounds for thirty seconds. After it has been triggered, the alarm is operational again. Note:
if you wish to lock your vehicle
without setting the alarm, lock it using the lock.
Warning
When the alarm is triggered, if a door, the boot or the bonnet are not closed
correctly, the siren sounds for amoment. Close the vehicle correctlyto set the alarm. Disarming Unlock the vehicle using the remote control key (the direction indicatorsflash for two seconds and the redlight on the switch goes out). Note:
if the red warning light flashes,
it is a sign that the alarm has been triggered during your absence.
To stop it, switch on the ignition.Note: when the alarm is set, but the
remote control no longer works:
unlock the doors using the key and open the door; the alarm istriggered;
switch the ignition on within tenseconds;
press the internal protection button 1
immediately. The alarm is disarmed.
* According to destination.
Page 98 of 141
02-02-2004
Automatic day/night interior mirror This automatically and gradually changes between the day and night positions.
To prevent dazzling, the glass of the mirror darkens automatically depending onthe intensity of the light from behind. It clears as the light (headlamps of follow-
ing vehicles, sunlight) decreases, ensuring maximum visibility. Operation Switch on the ignition and press switch 1:
Ð Indicator light 2lit (switch pressed): automatic operation.
Ð Indicator light 2off: automatic system off. The mirror remains at its most clear.
Special feature
To ensure maximum visibility during manoeuvres, the mirror clears automatical- ly when reverse gear is engaged. Manual interior mirror The interior mirror has two positions:
Ð day (normal),
Ð night (anti-dazzle).
To change from one to the other, push or pull the lever on the lower
edge of the mirror.
YOUR 406 COUPE IN DETAIL
120
AREAS FOR TOLL CARDS/
CAR PARK TICKETS The athermic windscreen has two non-reflective zones located eitherside of the base of the interior
mirror.
They are intended for affixing toll cards and/or car park tickets.
Page 107 of 141
DRIVING YOUR 406 COUPE127
CRUISE CONTROL Cruise control enables the vehicle to maintain a steady speed pro-
grammed by the driver, regardless ofthe road characteristics and withoutthe driver having to touch the accel-erator or brake pedals. In order for it to be memorised, the vehicle speed must be greater than25 m.p.h (40 km/h) or 40 m.p.h
(60 km/h), depending on the engine,and fourth gear at least must beengaged (second gear for the auto-matic gearbox). Operation
Place switch 1in the ONposition.
A speed can be memorised. Place switch 1in the OFF position
to cancel.
Memorising a speedAs soon as you reach the chosen speed, press button 2or 3. This
memorises the speed, which will be
maintained automatically. Note:
It is possible to accelerate and drive
momentarily at a speed greater than the memorised speed. When the acceleratorpedal is released, the vehicle will return tothe memorised speed. Cancelling the memorised speed If you wish to cancel the memorised speed: press button 4or the brake or
clutch pedal.
Recalling the memorised speedAfter cancellation, press button 4.
Your vehicle will return to the last memorised speed. Changing a memorised speed
To memorise a speed higher than the previous one: press button 3;
release it when you have reached the required speed.
To memorise a speed lower than theprevious one: press button 2;
release it when you have reached the required speed.
Cancelling the cruise control Place switch 1in the OFF position
or switch off the ignition.
Do not use cruise control on slippery roads or in heavytraffic. THE ABS ANTI-LOCK BRAKINGSYSTEM When used with approved
tyres in good condition, the ABS increases the stability and manoeu-vrability of your vehicle, particularlyon poor or slippery road surfaces. The anti-lock braking system comes into operation automatically whenthere is a risk of wheel lock.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system enables the optimum braking pres-
sure to be reached more quickly,thus reducing the stopping distance. It is triggered by the speed at which
the brake pedal is activated. The
effect of this is a reduction in theresistance of the pedal and an
increase in braking efficiency. The normal operation of the ABSmay make itself felt by slightvibrations of the brake pedal. In emergency braking, press very firmly without releasingthe pressure.
02-02-2004
Page 117 of 141
02-02-2004
CHECKING THE LEVELS Oil level Check the level regularly and top up between changes. Maximum con-sumption is 0.5 litres per 600 miles(1 000 km). The oil level should be checked with the vehicle level and the engine coldusing the oil gauge or the dipstick.Dipstick There are two marks on the dipstick: A=maximum
Never fill past this mark. B= minimum
To maintain the reliability of the engines and of theemission control sys-tems, the use of additivesin the engine oil is prohib-ited.
Oil change According to the information given in
"PEUGEOT SERVICING" .
Note: avoid any prolonged contact of
used oil with the skin.
Viscosity selection In all cases, the oil selected must meet the manufacturer's require-ments.
MAINTENANCE OF YOUR 406 COUPE
30
Brake and clutch fluid level:
- The level should always bebetween the DANGER and MAX
marks on the reservoir.
- If the level drops substantially, con- tact a PEUGEOT dealer immedi-
ately.
Fluid change:
- must be carried out according to the manufacturer's servicing schedule.
- use fluids recommended by the manufacturer, which fulfil DOT 4standards.
Note: the brake fluid is noxious and
very corrosive. Avoid any contactwith the skin. Coolant level Use the fluid recommended by the
manufacturer. When the engine is warm, the tem- perature of the coolant is controlledby the engine fan. Because this fan
can operate with the ignition off andbecause the cooling system is pres-surised, wait for at least one hourafter the engine has stopped beforecarrying out any work.
To avoid any risk of burns, slacken the cap to the first notch to releasethe pressure. When the pressure hasdropped, remove the cap and top upthe level. Used products Do not dispose of used oil, brake fluid or coolant down drains or on theground. Power steering fluid level Open the reservoir with the engine
cold at ambient temperature. Thelevel should always be above theMIN mark, close to the MAX mark.
Windscreen and headlamp* wash fluid level For best quality cleaning and for your
safety, we advise that you useproducts recommended by
PEUGEOT.
* According to destination.