wheel bolts Peugeot 406 C 2004 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2004, Model line: 406 C, Model: Peugeot 406 C 2004Pages: 141, PDF Size: 1.8 MB
Page 119 of 141
02-02-2004
CHANGING A WHEEL Access to the spare wheel and jack Lift the boot carpet using the lifting hook. Secure the hook behind theboot seal.Tools 1 -
Wheel brace.
2 - Centralising tool.
3 - Trim remover/wheel brace extension.
4 - Jack.
5 - Removable towing eye.
6 - Chrome trim tool.
The tool holder supports the boot
floor. Reposition it to prevent anydeformation of the floor whenloaded.
Tighten the spare wheel securing strap to prevent noise and for yoursafety in the event of a frontalimpact. Removal
Ð Park the vehicle on level, stable
and non-slippery ground.
Ð Apply the handbrake, engage first or reverse gear (position Pfor the
automatic gearbox).
Ð Remove the chrome trims using the tool 6(see the paragraph in
this chapter entitled 'Special fea- tures of alloy wheels'). Note: when the vehicle is delivered,
the anti-theft sockets are in the glove box.
Ð Loosen the wheel bolts.
MAINTENANCE OF YOUR 406 COUPE
32
Page 120 of 141
02-02-2004
Ð The jack is fitted with a systemwhich enables it to be folded or
unfolded rapidly. Take the jackfrom the toolkit and close it bypressing the ends A. Place the
jack at one of the four locations E
underneath the vehicle, as closeas possible to the wheel to bechanged. Unfold it by pulling theends A.
Ð Extend the jack using the wheel- brace 1and the extension 3.
Ð Take out a wheel bolt at the top and fit the centralising tool 2.
Ð Loosen the wheel bolts and remove the wheel. Fitting a wheel
Ð Position the wheel using the cen-
tralising tool to assist you.
Ð Tighten the bolts by hand, and remove the centralising tool.
Ð Partly tighten the bolts using the wheelbrace.
Ð Fold the jack and remove it.
Ð Fully tighten the wheel bolts using the wheelbrace.
Ð Replace the centre trim by pres- sing it with the palm of your hand.
MAINTENANCE OF YOUR 406 COUPE 33
For your safety, always change the wheel:
Ð on level, stable, non-slipperyground,
Ð with the handbrake applied,
Ð with first or reverse gearengaged (position Pfor the
automatic gearbox).
Ð never go underneath a vehiclewhich is supported only by ajack (use a ramp).
After changing the wheel Ð have the tightening of the bolts and the tyre pressure checkedby a PEUGEOT dealer as soonas possible,
Ð have the punctured tyre repaired and refit it to the vehi-cle as soon as possible.
Page 121 of 141
02-02-2004
MAINTENANCE OF YOUR 406 COUPE
34
Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), the chrometrim and then the plastic cover mustbe removed using tool
6, before
unscrewing the bolt using one of thetwo anti-theft sockets (which weregiven to you on delivery of your vehi-cle along with the duplicate keys andthe confidential card) and the wheelbrace 1.
Note: make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable youto obtain duplicate anti-theft sockets
from a PEUGEOT dealer.
* According to model or destination.Special features of alloy wheels Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool 6to remove the trims before
slackening the bolts.Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is normal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The sparewheel is secured by the cone shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels onto your vehicle, it isessential to use special bolts avail-
able from your PEUGEOT dealer.