change time Peugeot 406 C Dag 2004 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2004, Model line: 406 C Dag, Model: Peugeot 406 C Dag 2004Pages: 141, PDF Size: 1.8 MB
Page 14 of 141
02-02-2004
PEUGEOT SERVICING
Your vehicle benefits from extended service intervals.
¥ For petrol engines: every 20,000 miles (30 000 km) or every two years.
¥ For direct injection diesel engines: every 12,000 miles (20 000 km) or every two years. The service indicator informs you when each service is due; the point at which it is due is calculated from the last indicator zero reset (see corresponding section). This point is determined by two parameters: - the distance travelled,- the time elapsed since the last service. Note:the distance remaining may be weighted by the time factor, in accordance with the driver's style of driving.
The extension of the service intervals means that the engine oil level must be checked regularly: topping up of the oil between oil changes is normal. It is for this reason that the PEUGEOT network invites you to an intermediate visit between regular services.
The date of this service is not shown by the service indicator. It is to be carried out at least every 10,000 miles (15 000 km) for petrol engines and every 6,000 miles (10 000 km) for direct injection diesel engines.
A PEUGEOT dealer will carry out a quick check, and will top up the levels if necessary (oil, coolant, screenwash up to 2 litres). If the oil level is too low there is a risk of serious damage to the engine: check the engine oil level at least every 2,000 miles (3 000 km) or 3,000 miles (5 000 km), depending on the conditions of use The extended service intervals have been made possible by technical modifications to the vehicles and lubricants:
THUS IT IS ESSENTIAL TO ONLY USE LUBRICANTS WHICH ARE SUITED TO YOUR ENGINE AND RECOMMENDED BY
THE MANUFACTURER (see pages on "Lubricants").
MAINTENANCE OF YOUR 406 COUPE
18
Page 33 of 141
02-02-2004
This enables the following information to be displayed:
Ð the time,
Ð the date,
Ð the outside temperature (the ¡C symbol flashes when there is a risk of ice),
Ð the radio displays,
Ð the status of the doors. The display shows you whether a door, the boot or thebonnet is open and if the fuel filler cap is missing.
Ð the warning messages (e.g. ''battery low'') or information messages (e.g. "top up fuel tank''), displayed temporarily, can be cleared by pressing button 1
or 2,
Ð the trip computer. Setting the parameters Press button 1for two seconds to access the settings. The information flashes
to show it is ready to be modified.Then, individual presses on button 1allow you to scroll through the various data
in the following sequence:
Ð language in which the information is displayed,
Ð unit of distance (kms or miles),
Ð unit of temperature (Celsius or Fahrenheit),
Ð time format (12 then 24 hour mode)
Ð hour,
Ð minutes,
Ð year,
Ð month,
Ð day. Pressing button 2allows you to change the information selected. Maintain the
pressure for rapid scrolling.After ten seconds without action, the display returns to the main screen and the modified data are recorded.Display B
YOUR 406 COUPE IN DETAIL
114
Page 37 of 141
02-02-2004
GENERAL FUNCTIONS On/offWith the ignition key in the ACCESSORIES or IGNITION position, press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ignition being switched on.
Anti-theft systemThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Turn button Ato increase or decrease the volume.
AUDIO SETTINGS Press the "AUDIO"button several times in succession to access the bass (BASS), treble(TREB) , loudness
(LOUD) , fader(FAD), balance (BAL)and the automatic volume correction.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing the "AUDIO" button after configuration of the automatic volume correction.
Note: bass and treble settings are specific to each source. It is possible to set them differently for radio,
cassette and CD changer.
YOUR 406 COUPE IN DETAIL
54
Page 47 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL
64
GENERAL FUNCTIONS On/off With the ignition key in the ACCESSORIES or IGNITION position, press button Ato switch the set on or
off.The set can operate for 30 minutes without the vehicle ignition being switched on.
ANTI-THEFT SYSTEMThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Turn button Ato increase or decrease the volume of the set.
Note: If you have a telephone fitted with a "mute"signal output connected to the set, the set will automatically
change to "mute"when the telephone is used.
AUDIO SETTINGS Press the "AUDIO"button several times in succession to access the bass (BASS), treble (TREB) , loudness
(LOUD) , fader (FAD), balance (BAL)and the automatic volume correction.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing the "AUDIO" button after configuration of the automatic volume correction.
Note: the bass and treble settings are specific to each source. It is possible to set them differently for radio,
CD, or CD changer.
Page 57 of 141
02-02-2004
THE SATELLITE NAVIGATION SYSTEM IntroductionThe satellite navigation system guides you to the destination of yourchoice by means of vocal and visualinstructions. The heart of the system lies in the use of a map database and GPS
(Global Positioning System). Thisenables your position to be locatedby means of several satellites. The satellite navigation system
consists of the following components:
Ð the remote control,
Ð the display,
Ð the control unit,
Ð the last voice message recall control,
Ð the CD ROM.
Some functions or services
described in this guide may vary depending on the
CD ROM version or the countryThe remote control
There is a storage compartment for the remote control in front of the ashtray.Pointing the remote control at the screen enables the information contained in the various menus to be selected.
Direction arrows: These enable you to move around the screen and thus select a function.
On the welcome screen only, the Up and Down buttons enable the brightness of the screen to be adjusted.
menu : this button allows access to the main menu. It canbe used at any time.
esc : escape button "Short press": cancels the current operation and returns to the previous screen. "Press for more than 2 seconds": returns to the welcome screen. This button can be used in any menu. It is inactive during guidance.
mod : mode button "Short press": changes between date, navigation, radio and permanent locating.
val : validation button Confirms the function selected.
YOUR 406 COUPE IN DETAIL
74
Page 61 of 141
02-02-2004
Entering a new destination The last town entered is displayed.
To enter the name of another town, select each letter using the direction arrows then confirm ("VAL"button) for each
letter. If an error is made, the "Correct"function enables the last
letter entered to be deleted. As the name is entered, the "List"function indicates the
number of towns beginning with the same letters. If the list contains less than 5 names, these are displayed automat-
ically. Select a town then confirm ( "VAL"button).
The "Change" function enables the town entered to be
completely cleared. When the complete name of the town is displayed, select the "Validate" function then press the "VAL"button.
Note: following confirmation of a letter, only those letters
which could make up an existing name appear. Enter the name of the street. Select the
"Validate"function
then press the "VAL"button.
Note: the guidance can be activated from the time the town
is entered, without the name of a street or a number. To dothis, select the "Town centre" function.
YOUR 406 COUPE IN DETAIL
78
Enter the street number. Select the"Validate"function
then press the "VAL"button.
Note: the guidance can be activated as soon as the town
and street are entered, without a number. To do this, select the "Validate" function.
Page 65 of 141
02-02-2004
YOUR 406 COUPE IN DETAIL
82
Display configuration From the general menu, the "Configure display"menu
gives access to the following parameters:
Ð Adjustment of the brightness and the video display.
Ð Adjustment of the date and time.
Ð Selection of the language of the display and voice infor- mation (English, German, Spanish, French, Italian, Dutch).
Ð Adjustment of the mode and units. This allows selection of the display in km/h or mph, in degrees Celsius orFahrenheit and selection of the time format (12 or 24hour mode). Navigation options From the
"Navigation/guidance" menu, the "Navigation
options" menu offers the following options:
Ð Management of the directories. It enables an address stored under a name to be renamed or deleted. To do this, select the directory and the name to be changed.
Ð Voice synthesis volume adjustment.
Ð Deletion of all data stored in the two directories.
Ð Stopping or resuming of guidance. Two messages may be displayed depending on the previous status: "Resume guidance" or "Stop guidance" .
Page 95 of 141
02-02-2004
Range The display shows the distance that can still be covered with the fuelremaining in the tank. Note:this figure may rise if there is a
change in driving style or road sur- face, causing a significant drop incurrent fuel consumption. If there are less than 3 litres of fuel in the tank, only three segments will bedisplayed. Average consumption This is the ratio between the amount of fuel consumed and the distancetravelled since the computer was lastreset to zero.
Current fuel consumption This gives the fuel consumption recorded during the last two sec-
onds. This function is only displayedwhen the vehicle is travelling at morethan 12 m.p.h. (20 km/h). Average speed This is obtained by dividing the dis- tance travelled by the period of timethe vehicle has been in use (with theignition on), since the computer waslast reset to zero.Distance travelled This shows the distance travelled since the computer was last reset tozero. After the trip computer has been reset to zero, the range databecomes meaningful only after thevehicle has been in use for a certainperiod. If horizontal segments are displayed instead of figures when driving, con-
tact a PEUGEOT dealer.
YOUR 406 COUPE IN DETAIL
117
Page 104 of 141
02-02-2004
Sport and Snow programmes In addition to the autoadaptive pro- gramme, two special programmes
are available. The indicator light cor-responding to the programme selec-ted lights up on the instrument panel. Sport programme Once the vehicle has been started and position Dselected, press the
S button.
The gearbox automatically favoursdynamic driving. Snow programme This programme makes starting easier
and offers smooth driving in conditions
when traction is poor. Once the vehicle has been started and position Dselected, press the
button.
The gearbox adapts to driving onslippery roads.
Note : You can return to the autoadaptive
programme at any time.
Press the Sor button again to
cancel the current programme. Operating anomaly Any disruption of the system is indi- cated by the alternate flashing of thesport and snow lights on the instru-ment panel. In such a case, the gearbox will operate in downgrade mode (locked
in 3rd gear). You may feel a substan-tial knock when reverse is selectedfrom position
Por N(this does not
damage the gearbox). Do not exceed 60 m.p.h. (100 km/h), if regulations permit this.
Contact a PEUGEOT dealer without
delay.
DRIVING YOUR 406 COUPE
126
MANUAL GEARBOX Reverse*
To change to reverse gear, lift the ring under the gear lever knob andpush the gear lever to the left then tothe front. Reverse gear can only be engaged when the vehicle is stationary withthe engine idling.
* According to engine.
Page 105 of 141
02-02-2004
Sport and Snow programmes In addition to the autoadaptive pro- gramme, two special programmes
are available. The indicator light cor-responding to the programme selec-ted lights up on the instrument panel. Sport programme Once the vehicle has been started and position Dselected, press the
S button.
The gearbox automatically favoursdynamic driving. Snow programme This programme makes starting easier
and offers smooth driving in conditions
when traction is poor. Once the vehicle has been started and position Dselected, press the
button.
The gearbox adapts to driving onslippery roads.
Note : You can return to the autoadaptive
programme at any time.
Press the Sor button again to
cancel the current programme. Operating anomaly Any disruption of the system is indi- cated by the alternate flashing of thesport and snow lights on the instru-ment panel. In such a case, the gearbox will operate in downgrade mode (locked
in 3rd gear). You may feel a substan-tial knock when reverse is selectedfrom position
Por N(this does not
damage the gearbox). Do not exceed 60 m.p.h. (100 km/h), if regulations permit this.
Contact a PEUGEOT dealer without
delay.
DRIVING YOUR 406 COUPE
126
MANUAL GEARBOX Reverse*
To change to reverse gear, lift the ring under the gear lever knob andpush the gear lever to the left then tothe front. Reverse gear can only be engaged when the vehicle is stationary withthe engine idling.
* According to engine.