ignition Peugeot 407 2009 Workshop Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 142 of 250
1010PRACTICAL INFORMATION
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
r e fi t t h e b a t t e r y c o v e r w h e n y o u h a v e
fi n i s h e d .
Fuse N°
Rating
A
Functions
1 20 Engine management control unit.
2 15 Horn.
3 10 Front and rear wash-wipe.
4 20 Headlamp wash.
5 15 Engine management actuators (fuel pump,
purge canister solenoid valves, ...).
6 10 Automatic gearbox control unit.
7 10 Switching and protection unit, intake air
fl o w s e n s o r , c l u t c h s w i t c h , s i x - s p e e d
automatic gearbox switch, STOP switches,
electrochromatic mirror, panoramic roof
c o n c e a l i n g fl a p c o n t r o l s ( 4 0 7 S W ) .
8 20 Starter coil.
9 10 Xenon bulb electronic supply, STOP switch,
power steering electropump assembly,
four-speed automatic gearbox control unit,
automatic gearbox locking relay.
10 30 Engine management actuators (ignition coil,
solenoid valves, oxygen sensors).
11 40 Air conditioning blower or not used.
12 30 Windscreen wipers.
13 40 Built-in systems interface supply
(ignition positive).
14 30 Air pump.
Page 143 of 250
1010PRACTICAL INFORMATION
122
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installa-
tion of accessories not supplied and
not recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the ad-
ditional equipment connected exceeds
10 milliamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer. If the telephone is being used
when economy mode starts,
i t w i l l s t i l l b e p o s s i b l e t o fi n i s h
the call.
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. T h i s p e r i o d m a y b e s i g n i fi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.
Page 144 of 250
1010PRACTICAL INFORMATION
122
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installa-
tion of accessories not supplied and
not recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the ad-
ditional equipment connected exceeds
10 milliamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer. If the telephone is being used
when economy mode starts,
i t w i l l s t i l l b e p o s s i b l e t o fi n i s h
the call.
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. T h i s p e r i o d m a y b e s i g n i fi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.
Page 146 of 250
1010PRACTICAL INFORMATION
124
To start the vehicle from another
battery: BATTERY (LOCATED IN THE BOOT) *
* V e h i c l e s fi t t e d w i t h t h e 2 . 7 l i t r e H D I
24 V engine.
The battery is in the left boot trim.
To charge the battery using a bat-
tery charger (boot open):
fold down the panel to gain access
to the battery,
disconnect the battery,
follow the instructions for use given
by the battery charger manufacturer,
reconnect starting with the nega-
tive (-) terminal,
raise the panel and close it.
open the bonnet,
use the two additional positive (+)
and negative (-) terminals located
under the bonnet,
open the red cover of the positive
(+) terminal,
connect the red cable between the
positive (+) terminal and the positive
(+) terminal of the slave battery,
connect the green or black cable
between the negative (-) terminal
and the negative (-) terminal of the
slave battery,
operate the starter, let the engine run,
wait for the engine to return to idle,
then disconnect the cables,
close the red cover of the positive
(+) terminal,
r e fi t t h e l e f t s i d e c o v e r ,
close the bonnet. Before disconnecting the bat-
tery, you must wait for 2 minutes
after switching off the ignition.
Never disconnect a terminal
when the engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t fi r s t
disconnecting the terminals.
Open the windows and close the sun-
roof before disconnecting the battery.
If they do not operate normally follow-
ing reconnection of the battery, they
must be reinitialised (see paragraphs
"Reinitialisation of the electric win-
dows" and "Sunroof").
After every reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to allow the
electronic systems to be initialised.
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e x -
perienced after this, please contact a
PEUGEOT dealer.
On the 2.7 litre 24V HDI engine, if
there is no battery in the boot, do
not connect a slave battery to the
positive (+) and negative (-) termi-
nals under the bonnet as a short
circuit may occur.
The batteries contain harmful
substances such as sulphu-
ric acid and lead. They must
be disposed of in accordance
with regulations and must never be
discarded with household waste.
Take used batteries to an approved
collection point.