ignition Peugeot 407 2009 Service Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 104 of 250
7SAFETY
87
SEAT BELTS
Detection of fastening of the front
seat belts
When the ignition is switched on , if a
front passenger has not fastened his seat
belt and if the vehicle speed is below
13 mph (20 km/h) , you are warned by
lighting of the seat belt warning light .
The warning light switches off when the
seat belt(s) concerned is(are) fastened.
If the vehicle speed is above 13 mph
(20 km/h) , y o u a r e w a r n e d b y fl a s h i n g
of the seat belt warning light , an
audible signal and a message on the
multifunction display locating the un-
fastened seat belt(s).
Front seat belts with
pre-tensioner and force
limiter
In the event of a serious front impact,
the pre-tensioning system instantly
t i g h t e n s t h e s e a t b e l t s fi r m l y a g a i n s t
the bodies of the occupants.
The pre-tensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pressure
of the seat belt against the chest of the
occupant, so increasing his protection.
Rear seat belts
T h e r e a r s e a t s a r e a l l fi t t e d w i t h a
three-point inertia reel seat belt.
The rear side seat belts have a force
l i m i t e r a n d m a y b e fi t t e d w i t h a p r e -
tensioning inertia reel.
To fasten the seat belts
Pull the strap, then insert the
tongue into the buckle.
Check that the seat belt is secured
correctly by pulling the strap.
To unfasten the seat belts
Press the red button on the buckle. Before folding the seat back, pull the
strap and insert the seat belt tongue
into the buckle. This precaution will
ensure that each seat belt is in place
when the rear seats are lifted again.
Note: a bag or an animal
placed on the front passenger
seat may trigger the lighting of
the warning light.
The audible signal ceases and the
warning light switches off when the
seat belt concerned is fastened.
After two minutes without any action on
t h e s e a t b e l t s , t h e fl a s h i n g w a r n i n g l i g h t
remains on permanently and the audible
signal ceases. All of the warnings cease
when a door is opened or when the
engine is switched off.
Front seat belt height adjustment:
To lower the attachment point,
squeeze control 1 and slide it
downwards,
To raise the attachment point, slide
control 1 upwards.
Page 106 of 250
7SAFETY
89
AIR BAGS
The air bags have been designed to
maximise the safety of the occupants
(with the exception of the rear centre
passenger) in the event of violent col-
lisions. They supplement the action of
the force-limiting seat belts.
In this case, the electronic detectors
record and analyse the front and side
impacts suffered in the impact detection
zones:
- in the event of a serious impact, the air bags are deployed instantane-
ously and protect the occupants of
the vehicle (with the exception of the
rear centre passenger); immediately
a f t e r t h e i m p a c t , t h e a i r b a g s d e fl a t e
rapidly so that they do not hinder
the visibility of the occupants or their
possible exit from the vehicle,
- in the event of a minor impact or rear impact and in certain roll-over
conditions, the air bags will not be
deployed; the seat belt alone is
s u f fi c i e n t t o p r o v i d e m a x i m u m p r o -
tection in these situations. Front air bags
The front air bags protect the driver
and front passenger in the event of a
serious front impact in order to limit the
risks of injury to the head and chest.
They are folded in the centre of the
steering wheel for the driver and in the
fascia for the front passenger.
Impact detection zones
A. Front impact zone.
B. Side impact zone.
The deployment of one or
more air bags is accompanied
by a slight discharge of harm-
less smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
This smoke is not harmful, but sensi-
tive individuals may experience some
irritation.
The noise of the detonation may result
in a slight loss of hearing for a short
time. Activation
They are deployed simultaneously, ex-
cept in cases where the passenger's
front air bag is disarmed, in the event
of a serious front impact applied to all
or part of the front impact zone
A , in the
longitudinal centreline of the vehicle
on a horizontal plane directed from the
front to the rear of the vehicle.
T h e f r o n t a i r b a g i n fl a t e s b e t w e e n t h e
front occupant of the vehicle and the
fascia to cushion his forward movement.
The air bags do not operate
when the ignition is off.
This equipment only operates
once. If a second impact occurs
(during the same or a subsequent
accident), the air bag will not operate.
Page 107 of 250
7SAFETY
90
Disarming the front
passenger's front air bag * Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" position
to re-activate the air bag and thus ensure
its safety function.
To ensure the safety of your child, it
is essential to disarm the passenger
air bag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the air bag
w e r e t o i n fl a t e .
With the ignition switched off
,
insert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the key
keeping the slot in this position. The steering column air bag protects
the driver's knees in the event of a
serious front impact.
It is incorporated in the fascia below
the steering column.
In the event of a malfunction
* According to country. Activation
It is deployed at the same time as the
front air bags.
Instrument panel warning light.
If this warning light comes on, accompa-
nied by an audible signal and a message
on the multifunction display, contact a
PEUGEOT dealer to have the system
checked. The air bags may no longer
be deployed in the event of a serious
impact. Steering column air bag
When the ignition is on, this
warning light remains lit on the
instrument panel for the duration
of disarming.
In the "OFF" position, the passenger
air bag will not be triggered in the event
of an impact.
Page 110 of 250
7SAFETY
90
Disarming the front
passenger's front air bag * Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" position
to re-activate the air bag and thus ensure
its safety function.
To ensure the safety of your child, it
is essential to disarm the passenger
air bag when you install a rear-facing
child seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the air bag
w e r e t o i n fl a t e .
With the ignition switched off
,
insert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the key
keeping the slot in this position. The steering column air bag protects
the driver's knees in the event of a
serious front impact.
It is incorporated in the fascia below
the steering column.
In the event of a malfunction
* According to country. Activation
It is deployed at the same time as the
front air bags.
Instrument panel warning light.
If this warning light comes on, accompa-
nied by an audible signal and a message
on the multifunction display, contact a
PEUGEOT dealer to have the system
checked. The air bags may no longer
be deployed in the event of a serious
impact. Steering column air bag
When the ignition is on, this
warning light remains lit on the
instrument panel for the duration
of disarming.
In the "OFF" position, the passenger
air bag will not be triggered in the event
of an impact.
Page 112 of 250
8DRIVING
94
Gear selection gate
Move the lever in the gate to select
a position.
The indicator light corresponding to the position selected appears on
the instrument panel screen.
P ark: to immobilise the vehicle and to
start the engine, with the handbrake on.
R everse: to reverse (select this position
with the vehicle stationary, engine at idle).
N eutral: to start the engine and to park,
with the handbrake on.
Note: if position N is inadvertently
engaged while driving, allow the engine to
return to idle before engaging position D
then accelerate.
D rive: to drive in automatic mode.
M anual: to drive selecting the gears.
S: sport programme.
: snow programme.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX
The four or six speed automatic gearbox
offers, as required, the comfort of the
auto-adaptive programme enhanced
by a selection suited to dynamic driving
conditions: sport, or to driving on a
slippery road: snow.
However, manual selection is still possible
using the gear lever.
Moving Off
With the engine running, move off from
position P :
to exit position P, it is essential
to press the brake pedal,
select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
To move off from position N :
with your foot on the brake, release
the handbrake,
select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
Starting the engine
with the handbrake on, select position
P or N in the gate,
turn the ignition key. When the engine is at idle,
brakes not applied, if position
R , D or M is selected, the
vehicle moves even without the
accelerator being pressed.
Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the engine
running, as the vehicle moves
even without the accelerator being
pressed.
With the ignition off, if the
lever is not in position P , an
audible signal is heard when
the driver's door is opened, or
after approximately 45 seconds. Move
the lever to position P . The audible
signal ceases.
When maintenance operations need to
be carried out with the engine running,
apply the handbrake and select the
P ark position.
Page 116 of 250
8DRIVING
98
Note: the speed memo-
rised is cancelled auto-
matically if the vehicle
speed is less than 25 mph
(40 km/h), or if the manual gearbox
is in a gear lower than fourth (second
gear for the automatic gearbox) or if
the ESP is activated. Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
t h e d a s h e s fl a s h f o r a f e w s e c o n d s :
Contact a PEUGEOT dealer to have
the system checked. Do not use the cruise control
on slippery roads or in heavy
t r a f fi c .
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
To memorise a speed lower than the
previous one:
press button 2 ;
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase
or decrease of the value in steps of
5 mph (5 km/h).
Recalling the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memo-
rised speed. The display indicates
(e.g. at 70 mph (110 km/h)):
Cancelling the memorised speed
Place switch 1 in position 0 or LIMIT
or switch off the ignition.
Page 117 of 250
8DRIVING
99
Selecting the function
Place switch 1 in the LIMIT position.
The limiter is not yet active. By default
the display indicates:
Switching the function off
Place switch 1 in position 0 or
CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in the
memory.
Memorising a speed
A speed can be memorised without
activation of the limiter.
Pressing buttons 2 and 3 decreases or
increases the speed.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase
or decrease of the value in steps of
5 mph (5 km/h). Activation/deactivation of the
limiter
Pressing button
4 activates the limiter,
pressing this button again deactivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):
On a steep descent or if the
driver accelerates sharply, the
speed limiter, which does not
act on the brakes, is not able
to prevent the vehicle from exceeding
the programmed speed.
In no circumstances does the speed
limiter replace the requirement to respect
speed limits, nor does it replace the
need for vigilance and responsibility on
the part of the driver.
The driver must remain vigilant and
stay in complete control of his vehicle.
The operations must be car-
ried out with the engine run-
ning.
Limiter function
This prevents the vehicle speed
exceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).
Page 127 of 250
9CHECKS
110
CHECKING THE LEVELS
These are normal maintenance opera-
tions which keep your vehicle in good
working order. Consult the instructions
in the PEUGEOT Network or in the
servicing booklet enclosed with this
handbook.
Dipstick There are two marks on
the dipstick:
A = m a x i m u m
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil is
prohibited.
Oil level
Check the level regularly and top
up between changes.
Check the level with the vehicle level,
the engine having been off for more
than 15 minutes, using the dipstick. Oil change
It is imperative that this is carried out at
t h e i n t e r v a l s s p e c i fi e d a n d t h e v i s c o s i t y
of the oil chosen must meet the require-
ments laid down in the manufacturer’s
servicing schedule. Consult the instruc-
tions in the PEUGEOT Network.
Note: avoid used oil coming into pro-
longed contact with the skin. Empty the
used oil into the containers provided for
this purpose in the PEUGEOT Network. system is pressurised, wait for at least
one hour after the engine has stopped
before carrying out any work.
Oil filter
Replace the cartridge regularly in
accordance with the recommendations
of the servicing schedule.
Brake fluid change
U s e t h e fl u i d r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l s D O T 4
Standards.
I t i s i m p e r a t i v e t h a t t h e b r a k e fl u i d i s
c h a n g e d a t t h e i n t e r v a l s s p e c i fi e d i n
accordance with the manufacturer’s
servicing schedule.
Note: avoid all contact with the skin,
t h e b r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive. Used oil
Power steering reservoir
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
Cooling system Windscreen and headlamp
wash level
To guarantee optimum cleaning and
a v o i d f r e e z i n g , t h i s fl u i d s h o u l d n o t b e
topped up or replaced with water. Slacken the cap by two turns
to release the pressure to pre-
vent any risk of scalding. When
the pressure has dropped,
remove the cap and top up the
level.
Note: the coolant does not need to be
changed.
U s e t h e fl u i d r e c o m m e n d e d
by the manufacturer.
When the engine is warm, the
temperature of the coolant is
controlled by the engine fan. As this
fan can operate with the ignition key
removed and because the cooling Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or onto the ground.
Important: if you have to
r e m o v e / r e fi t t h e e n g i n e s t y l e
cover, handle it with care to
a v o i d d a m a g i n g t h e fi x i n g c l i p s .
Page 139 of 250
1010PRACTICAL INFORMATION
119
Fuse N°
Rating
A
Functions
F9 30 Lighter, telematics (according to country), rear 12V accessories so cket (100 W max).
F10 15 T y r e u n d e r - i n fl a t i o n d e t e c t i o n u n i t .
F11 15 Diagnostic socket, ignition switch.
F12 30 Hands-free kit, trailer socket, trailer fuse box, audible rear pa
rking assistance,
passenger’s electric seat, rain and brightness sensor, alarm.
F13 5 Engine fuse box, windscreen wipers relay control.
F14 15 Driver’s electric seat, instrument panel, air conditioning control panel, air bags control unit.
F15 15 Electric child lock, rear doors deadlocking.
F17 40 Heated rear screen.
FS1 - PARC shunt.
Page 141 of 250
1010PRACTICAL INFORMATION
122
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installa-
tion of accessories not supplied and
not recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the ad-
ditional equipment connected exceeds
10 milliamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer. If the telephone is being used
when economy mode starts,
i t w i l l s t i l l b e p o s s i b l e t o fi n i s h
the call.
Placing the wiper blades in the
maintenance position
Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
Replacing a blade
Lift the arm, then unclip the blade
and remove it.
Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. T h i s p e r i o d m a y b e s i g n i fi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.