ESP Peugeot 407 2009 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 6 of 250
FAMILIARISATION
INSTRUMENTS AND CONTROLS
1. Multifunction display.
2. Audio and telematics system.
3. Automatic air conditioning controls.
4. Deactivation of the audible parking
assistance.
Central locking from the inside.
Alarm control.
Hazard warning lights.
SPORT suspension control.
Deactivation of the ESP system.
Child lock.
5. Ashtray/Front lighter (100 W max).
6. Gear lever.
7. Handbrake.
8. Retractable cup/can holder.
9. Armrest with storage compartment
and USB socket.
10. 12 volt accessories socket
(100 W max).
11. Rear ashtray.
141
212
PC Com
PC Nav
184
PC Sound
Page 12 of 250
FAMILIARISATION
Instrument panel
A. When the ignition is on, the fuel
gauge needle should rise.
B. When the engine is running, its as-
sociated low level warning light
should switch off.
C. When the ignition is on, the oil level
indicator should display "OIL OK"
for a few seconds.
If the levels are not correct, top up the
level which is low. Lighting of the indicator light indicates the
status of the corresponding function.
When the ignition is on, the orange and
red warning lights come on.
When the engine is running, these
warning lights should switch off.
If any warning light remains on, refer to
the page concerned.
18
20
103
A. Audible front/rear parking
assistance off.
B. Central locking.
C. Interior protection alarm
off.
D. Hazard warning lights.
E. Selection of the electroni-
cally controlled suspen-
sion.
F. Electronic stability pro-
gramme ESP off.
63
66
85
96
85
Warning lights Controls bar
Page 21 of 250
1INSTRUMENTS and CONTROLS
22
Battery charge warning
light
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
light
This indicates that the tyre pressure is
too low.
A message on the multifunction display
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lights Activation warning light
Operation warning light
Deactivation warning light
Malfunction warning light
Power steering warning
light
This indicates a power steering fault.
It is linked with the STOP warning
light.
Consult a PEUGEOT dealer. Handbrake warning light
This indicates that the handbrake is
still applied or has not been released
correctly.
It is linked with the braking system
warning light. Low wash-wipe and
h e a d l a m p w a s h fl u i d l e v e l
warning light
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the wash-wipe and headlamp wash
fl u i d r e s e r v o i r .
Engine oil level warning
light
This indicates a critical engine oil level
(too low).
WARNING LIGHTS ON THE INSTRUMENT PANEL DISPLAY
These warning lights are displayed on
the instrument panel display.
STOP warning light
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, brak-
ing system or punctured tyre warning
lights.
Stop immediately.
Consult a PEUGEOT dealer.
Punctured tyre warning light
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Consult a PEUGEOT dealer.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 24 of 250
1INSTRUMENTS and CONTROLS
25
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever
position indicator lights
This indicates an automatic
gearbox malfunction.
4 or 6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. These correspond to the manual con-
trol of the gearbox, four or six speed.
When the engine speed is too low or
too high in relation to the gear engaged,
t h e g e a r s e l e c t e d fl a s h e s f o r a f e w s e c -
onds, then the actual gear is displayed,
the auto-adaptive programme having
taken control temporarily.
Engine oil temperature
indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone
C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. "Manual" indicator lights
Page 57 of 250
3COMFORT
55
TRANSPORTING LONG OBJECTS * (407 SW)
Rear seat (see corresponding
paragraph):
Tilt the seat cushion,
R e m o v e t h e h e a d r e s t r a i n t s ,
T i l t t h e s e a t b a c k .
Note: w h e n r e p o s i t i o n i n g ,
ensure that the front and
rear seat backs are secured
c o r r e c t l y .
Precautions
- The long object must be p l a c e d o n t h e e n d o f t h e
front seat back and on the
r e a r s e a t c u s h i o n .
- D o n o t p l a c e a l o a d i n e x c e s s of 30 kg on the front of the seat
b a c k .
- Do not load blunt objects, this could damage the rear of the front
s e a t b a c k ( s t o r a g e p o c k e t ) .
Front passenger seat:
T i l t t h e s e a t b a c k a p p r o x i m a t e l y
25° towards the rear (in relation to
t h e v e r t i c a l p o s i t i o n ) u s i n g t h e s e a t
back angle adjustment control (see
c o r r e s p o n d i n g p a r a g r a p h ) .
Lift control A u p w a r d s t o r e l e a s e
t h e s e a t b a c k .
Without releasing control A , p r e s s
o n t h e t o p o f t h e s e a t b a c k a n d
m o v e w i t h i t u n t i l i t i s f o l d e d .
* A c c o r d i n g t o v e r s i o n .
Page 75 of 250
4ACCESS
67
ELECTRIC WINDOWS
Automatic operation:
To open or close the window, press
or pull switch fully: the window opens
or closes completely when the switch
is released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one
minute after the key has been removed
from the ignition.
Once this time has elapsed, the electric
windows will not operate. To reactivate
them, switch the ignition on again.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
I n t h e e v e n t o f c o n t a c t d u r i n g o p e r a -
tion of the windows, you must reverse
the movement of the window. To do
this, press the switch concerned.
W h e n t h e d r i v e r o p e r a t e s t h e p a s s e n -
ger electric window switches, he must
e n s u r e t h a t n o o n e i s p r e v e n t i n g c o r -
rect closing of the windows.
T h e d r i v e r m u s t e n s u r e t h a t t h e p a s s e n -
gers use the electric windows correctly.
Be aware of children when operating
the windows. REINITIALISATION OFTHE WINDOWS
F o l l o w i n g r e c o n n e c t i o n o f t h e b a t -
t e r y , t h e s a f e t y a u t o - r e v e r s e f u n c t i o n
m u s t b e r e i n i t i a l i s e d : t h e s a f e t y a u t o -
reverse function is not active during
these operations.
- l o w e r t h e w i n d o w c o m p l e t e l y , t h e n raise it, it will rise in steps of a few
centimetres each time the switch is
p r e s s e d . R e p e a t t h e o p e r a t i o n u n -
til the window closes completely,
- c o n t i n u e t o p r e s s t h e s w i t c h f o r a t least one second after reaching
this position, window closed.
Safety auto-reverse
When the window rises and meets an
o b s t a c l e , i t s t o p s a n d i m m e d i a t e l y p a r -
tially lowers again.
In the event of unwanted opening of the
w i n d o w o n c l o s i n g , p r e s s t h e s w i t c h u n -
til the window opens completely, then
pull the switch immediately until the
window closes. Continue to hold the
switch for approximately one second
after the window has closed.
T h e s a f e t y a u t o - r e v e r s e f u n c t i o n i s n o t
active during this operation.
Disarming the rear window
controls
For the safety of your children, press
switch 5 to prevent operation of the rear
windows irrespective of their position.
When the button is pressed down, the
s w i t c h e s a r e d i s a r m e d . W h e n t h e b u t -
ton is raised, the switches are active.
Manual operation:
To open or close the window, press or
pull the switch gently. The window stops
as soon as the switch is released.
1. Driver's electric window
switch.
2. Passenger's electric window
switch.
3. Rear right electric window
switch.
4. Rear left electric window
switch.
5. Disarming of the rear electric
window switches (child lock).
Page 93 of 250
5
79
REAR COURTESY LIGHT ( S A L O O N ) REAR READING LIGHTS ( 4 0 7 S W ) Sill illumination
T h e s i l l l i g h t i n g i s a t t h e b o t t o m o f e a c h
door panel.
T h e l a m p s c o m e o n a u t o m a t i c a l l y
when a door is opened and switch off
a u t o m a t i c a l l y w h e n a l l o f t h e d o o r s a r e
closed.
Boot light
The boot light is located in the right-
h a n d b o o t t r i m .
I t c o m e s o n a u t o m a t i c a l l y w h e n t h e
boot is opened and switches off auto-
m a t i c a l l y w h e n t h e b o o t i s c l o s e d .
1. Courtesy light
2. Map reading lights
With the key in the ignition on or starting
position, operate the relevant switch.
T h e r e a r c o u r t e s y l i g h t c o m e s o n w h e n t h e
i g n i t i o n k e y i s r e m o v e d , o n u n l o c k i n g t h e
vehicle or on opening one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.
Pressing switch 1 turns on the rear
courtesy light.
The courtesy light can be deactivated
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l i g h t s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
To re-activate the lights, press the
switch, with the door open. With the key in the ignition on or starting
position, press the corresponding
switch.
T h e r e a r r e a d i n g l i g h t s c o m e o n w h e n
t h e k e y i s r e m o v e d f r o m t h e i g n i t i o n
and when the vehicle is unlocked.
They switch off gradually when the
ignition is switched on or when the
vehicle is locked.
Pressing switch 1 switches on the
rear reading light concerned for
t e n m i n u t e s .
Page 100 of 250
7SAFETY
85
HORN
Press one of the spokes of the steering
wheel.
HAZARD WARNING LAMPS
Automatic lighting of hazard
warning lights *
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lights come on automatically.
T h e y s w i t c h o f f a u t o m a t i c a l l y t h e fi r s t
time you accelerate.
It is also possible to switch them off by
pressing the button.
* According to country.
ELECTRONIC STABILITY CONTROL (ESP)
This system is linked and complemen-
tary to the ABS system.
I n t h e e v e n t o f a s i g n i fi c a n t v a r i a t i o n
between the trajectory of the vehicle
and the path required by the driver,
the ESP monitors wheel by wheel and
acts automatically on the engine and
on the brake of one or more wheels, to
put the vehicle back on course, within
the limit of the laws of physics.
ESP operation The indicator light comes on. Disarming the ESP
In exceptional conditions (starting the
vehicle when it is stuck in the mud,
immobilised in snow, on unstable
ground...), it may be advisable to dis-
arm the ESP.
Press the "ESP OFF" switch, lo-
cated on the centre console.
The switch lights up and the warning
light comes on: the ESP no longer acts
on the operation of the engine.
Instrument panel indicator
light.
The system is triggered again:
automatically if the ignition is
switched off,
automatically above 30 mph (50 km/h),
manually by pressing the switch
again.
Press the button, the direction indicators
fl a s h .
They can operate with the ignition off.
Page 101 of 250
7SAFETY
85
HORN
Press one of the spokes of the steering
wheel.
HAZARD WARNING LAMPS
Automatic lighting of hazard
warning lights *
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lights come on automatically.
T h e y s w i t c h o f f a u t o m a t i c a l l y t h e fi r s t
time you accelerate.
It is also possible to switch them off by
pressing the button.
* According to country.
ELECTRONIC STABILITY CONTROL (ESP)
This system is linked and complemen-
tary to the ABS system.
I n t h e e v e n t o f a s i g n i fi c a n t v a r i a t i o n
between the trajectory of the vehicle
and the path required by the driver,
the ESP monitors wheel by wheel and
acts automatically on the engine and
on the brake of one or more wheels, to
put the vehicle back on course, within
the limit of the laws of physics.
ESP operation The indicator light comes on. Disarming the ESP
In exceptional conditions (starting the
vehicle when it is stuck in the mud,
immobilised in snow, on unstable
ground...), it may be advisable to dis-
arm the ESP.
Press the "ESP OFF" switch, lo-
cated on the centre console.
The switch lights up and the warning
light comes on: the ESP no longer acts
on the operation of the engine.
Instrument panel indicator
light.
The system is triggered again:
automatically if the ignition is
switched off,
automatically above 30 mph (50 km/h),
manually by pressing the switch
again.
Press the button, the direction indicators
fl a s h .
They can operate with the ignition off.
Page 102 of 250
7SAFETY
86
Operating fault
When a malfunction of the system oc-
curs, the warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked. Instrument panel indicator light.
The ESP offers exceptional
safety during normal driving,
but this should not encourage
the driver to take extra risks
(late braking) or drive at high
speed.
Correct operation of the system depends
on compliance with the manufacturer's
recommendations regarding the wheels
(tyres and rims), the braking compo-
nents, the electronic components and
the PEUGEOT assembly and operation
procedures.
After an impact, have the system
checked by a PEUGEOT dealer. ANTI-LOCK BRAKING SYSTEM (ABS)
The ABS increases the stability and
manoeuvrability of your vehicle on
braking, in particular on poor or slippery
road surfaces.
This system comes into operation
automatically when there is a risk of
wheel lock.
Normal operation of the ABS may
make itself felt by slight vibrations of
the brake pedal.
This indicates that the ABS is
faulty.
It comes on on the instrument
panel screen also.
If it comes on permanently above
6 mph (10 km/h), it indicates an ABS
malfunction.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
EMERGENCY BRAKING ASSISTANCE SYSTEM
In an emergency, this system enables
the optimum braking pressure to be
reached more quickly, thus reducing
the stopping distance.
It is triggered by the speed at which
the brake pedal is activated.
The effect of this is a reduction in the
resistance of the pedal and an increase
i n b r a k i n g e f fi c i e n c y .
When braking in an emergency, press
fi r m l y w i t h o u t r e l e a s i n g t h e p r e s s u r e .
In emergency braking, press
v e r y fi r m l y w i t h o u t r e l e a s i n g
the pressure.
Note: when changing wheels (tyres
and rims), make sure that these are
approved.