lock Peugeot 407 2010 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 407, Model: Peugeot 407 2010Pages: 249, PDF Size: 14.69 MB
Page 76 of 249
4ACCESS
68
BOOT (SALOON) TAILGATE AND REAR SCREEN (407SW) Partial opening of the rear screen
Opening the tailgate and rear
screen
The tailgate and rear screen cannot
be opened at the same time.
With the rear screen closed, to open
the tailgate , operate the handle A ,
then lift the tailgate.
With the tailgate closed, to open the
rear screen , operate the handle B ,
then lift the rear screen.
The boot lighting is controlled by open-
ing the tailgate or the rear screen.
If the permanent locking of the
boot is activated, opening is
only possible by pressing the
remote control button.
Notes: the tailgate and rear
screen lock automatically when
driving at 6 mph (10 km/h) and
unlock when one of the doors
is opened.
When the rear wiper is in a wiping
position, the rear screen cannot be
opened until the end of the cycle.
Close the rear screen using the wiper
arm or by pressing the centre of the
glass.
To open the boot, press the push button
and raise the tailgate.
The locking or unlocking of the tailgate
and rear screen is simultaneous with
that of the doors. With the tailgate closed, to partially
open the
rear screen , press and hold
the unlocking button C on the remote
control.
Page 77 of 249
4ACCESS
69
"Rear screen open" warning
When the engine is running , if the
rear screen is not fully closed, you are
warned by a message on the multi-
function screen.
When the vehicle is moving (speed
greater than 6 mph (10 km/h)), if the
rear screen is not fully closed, you are
warned by an audible signal, a mes-
sage on the multifunction screen and
lighting of the service warning lamp. Tailgate release
This enables the tailgate to be un-
locked in the event of a central locking
fault.
- Fold back the rear seats to gain
access to the lock from inside the
boot.
- Insert a small screwdriver into hole A
of the lock to unlock the tailgate.
Page 84 of 249
5
75
Automatic illumination of
headlamps
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
t h e s u n s h i n e s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t . T h e l i g h t i n g w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y , y o u
m u s t s w i t c h t h e d i p p e d b e a m h e a d -
l a m p s o n m a n u a l l y . Activation Manual "Guide-me-home" lighting
When you leave your vehicle, the side-
l a m p s a n d d i p p e d b e a m h e a d l a m p s
can be left on for a few seconds.
When the function is activated, the
i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
To deactivate or activate the
function, use the "Persona-
l i s a t i o n - c o n fi g u r a t i o n "
m e n u o n y o u r m u l t i f u n c t i o n
screen.
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
i l l u m i n a t i o n o f h e a d l a m p s s "
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c g u i d e - m e - h o m e
lighting" function, use the
"Personalisation - confi-
guration" m e n u o n y o u r
m u l t i f u n c t i o n s c r e e n .
The duration of the lighting
can be set via the "Person-
a l i s a t i o n - c o n fi g u r a t i o n "
m e n u o f y o u r m u l t i f u n c t i o n
screen.
Automatic "Guide-me-home"
lighting
When you leave your vehicle
with
the automatic illumination of head-
lamps a c t i v a t e d , t h e s i d e l a m p s a n d
d i p p e d b e a m h e a d l a m p s r e m a i n o n
for the duration selected after the igni-
tion is switched off.
Deactivation
When the function is deactivated,
t h e i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c i l -
l u m i n a t i o n o f h e a d l a m p s .
If the sunshine/brightness sensor
does not function correctly, the
s i d e l a m p s a n d d i p p e d b e a m h e a d l a m -
p s c o m e o n .
Consult a PEUGEOT dealer.
Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Page 85 of 249
5
75
Automatic illumination of
headlamps
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
t h e s u n s h i n e s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t . T h e l i g h t i n g w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y , y o u
m u s t s w i t c h t h e d i p p e d b e a m h e a d -
l a m p s o n m a n u a l l y . Activation Manual "Guide-me-home" lighting
When you leave your vehicle, the side-
l a m p s a n d d i p p e d b e a m h e a d l a m p s
can be left on for a few seconds.
When the function is activated, the
i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
To deactivate or activate the
function, use the "Persona-
l i s a t i o n - c o n fi g u r a t i o n "
m e n u o n y o u r m u l t i f u n c t i o n
screen.
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
i l l u m i n a t i o n o f h e a d l a m p s s "
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c g u i d e - m e - h o m e
lighting" function, use the
"Personalisation - confi-
guration" m e n u o n y o u r
m u l t i f u n c t i o n s c r e e n .
The duration of the lighting
can be set via the "Person-
a l i s a t i o n - c o n fi g u r a t i o n "
m e n u o f y o u r m u l t i f u n c t i o n
screen.
Automatic "Guide-me-home"
lighting
When you leave your vehicle
with
the automatic illumination of head-
lamps a c t i v a t e d , t h e s i d e l a m p s a n d
d i p p e d b e a m h e a d l a m p s r e m a i n o n
for the duration selected after the igni-
tion is switched off.
Deactivation
When the function is deactivated,
t h e i n d i c a t o r l a m p c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l s c r e e n .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c i l -
l u m i n a t i o n o f h e a d l a m p s .
If the sunshine/brightness sensor
does not function correctly, the
s i d e l a m p s a n d d i p p e d b e a m h e a d l a m -
p s c o m e o n .
Consult a PEUGEOT dealer.
Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Page 90 of 249
5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
w i n d s c r e e n w i p e r s o p e r a t e f o r a fi x e d
period.
T h e h e a d l a m p w a s h i s a l s o a c t i v a t e d ,
if the headlamps are on .
W h e n t h e m i n i m u m l e v e l o f
the reservoir is reached, this
w a r n i n g l i g h t c o m e s o n , a c -
c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
m u l t i - f u n c t i o n d i s p l a y .
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n w a s h /
h e a d l a m p w a s h r e s e r v o i r .
T h e w a r n i n g l i g h t c o m e s o n e a c h t i m e
the stalk is operated, until the reservoir
i s fi l l e d . FRONT COURTESY LAMP
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open.
Screenwash/headlamp wash low
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
T h e f r o n t c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.
Pressing switch 1 turns on the front
c o u r t e s y l a m p .
Rear wash-wipe
Note: the rear wiper and rear
wash-wipe functions are de-
a c t i v a t e d a u t o m a t i c a l l y w h e n
the rear screen is opened.
T u r n t h e r i n g b e y o n d t h e fi r s t n o t c h ,
the wash-wipe then the wiper operate
f o r a s e t p e r i o d o f t i m e .
Page 91 of 249
5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
w i n d s c r e e n w i p e r s o p e r a t e f o r a fi x e d
period.
T h e h e a d l a m p w a s h i s a l s o a c t i v a t e d ,
if the headlamps are on .
W h e n t h e m i n i m u m l e v e l o f
the reservoir is reached, this
w a r n i n g l i g h t c o m e s o n , a c -
c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
m u l t i - f u n c t i o n d i s p l a y .
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n w a s h /
h e a d l a m p w a s h r e s e r v o i r .
T h e w a r n i n g l i g h t c o m e s o n e a c h t i m e
the stalk is operated, until the reservoir
i s fi l l e d . FRONT COURTESY LAMP
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open.
Screenwash/headlamp wash low
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
T h e f r o n t c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.
Pressing switch 1 turns on the front
c o u r t e s y l a m p .
Rear wash-wipe
Note: the rear wiper and rear
wash-wipe functions are de-
a c t i v a t e d a u t o m a t i c a l l y w h e n
the rear screen is opened.
T u r n t h e r i n g b e y o n d t h e fi r s t n o t c h ,
the wash-wipe then the wiper operate
f o r a s e t p e r i o d o f t i m e .
Page 92 of 249
5
80
REAR COURTESY LAMP (SALOON) REAR READING LAMPS (407 SW) Sill illumination
T h e s i l l l i g h t i n g i s a t t h e b o t t o m o f e a c h
door panel.
T h e l a m p s c o m e o n a u t o m a t i c a l l y
when a door is opened and switch off
a u t o m a t i c a l l y w h e n a l l o f t h e d o o r s a r e
closed.
Boot light
The boot light is located in the right-
h a n d b o o t t r i m .
I t c o m e s o n a u t o m a t i c a l l y w h e n t h e
boot is opened and switches off auto-
m a t i c a l l y w h e n t h e b o o t i s c l o s e d .
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or start-
ing position, operate the relevant
switch.
T h e r e a r c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.
Pressing switch 1 turns on the rear
c o u r t e s y l a m p .
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open. With the key in the ignition on or start-
ing position, press the corresponding
switch.
T h e r e a r r e a d i n g l a m p s c o m e o n w h e n
t h e k e y i s r e m o v e d f r o m t h e i g n i t i o n
and when the vehicle is unlocked.
They switch off gradually when the ig-
nition is switched on or when the ve-
hicle is locked.
Pressing switch 1 switches on the
r e a r r e a d i n g l a m p c o n c e r n e d f o r
t e n m i n u t e s .
Page 101 of 249
7SAFETY
87
Operating fault
When a malfunction of the system oc-
curs, the warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked. Instrument panel indicator light.
The ESP offers exceptional
safety during normal driving,
but this should not encourage
the driver to take extra risks
(late braking) or drive at high speed.
Correct operation of the system depends
on compliance with the manufacturer's
recommendations regarding the wheels
(tyres and rims), the braking compo-
nents, the electronic components and
the PEUGEOT assembly and operation
procedures.
After an impact, have the system
checked by a PEUGEOT dealer. ANTI-LOCK BRAKING SYSTEM (ABS)
The ABS increases the stability and
manoeuvrability of your vehicle on
braking, in particular on poor or slip-
pery road surfaces.
This system comes into operation
automatically when there is a risk of
wheel lock.
Normal operation of the ABS may
make itself felt by slight vibrations of
the brake pedal.
This indicates that the ABS is
faulty.
It also comes on on the instru-
ment panel screen.
If it comes on permanently above
6 mph (10 km/h), it indicates an ABS
malfunction.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
EMERGENCY BRAKING ASSISTANCE SYSTEM
In an emergency, this system enables
the optimum braking pressure to be
reached more quickly, thus reducing
the stopping distance.
It is triggered by the speed at which
the brake pedal is activated.
The effect of this is a reduction in the
resistance of the pedal and an in-
c r e a s e i n b r a k i n g e f fi c i e n c y .
When braking in an emergency, press
fi r m l y w i t h o u t r e l e a s i n g t h e p r e s s u r e .
In emergency braking, press
v e r y fi r m l y w i t h o u t r e l e a s -
ing the pressure.
Note: when changing wheels (tyres
and rims), make sure that these are
approved.
Page 102 of 249
7SAFETY
87
Operating fault
When a malfunction of the system oc-
curs, the warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked. Instrument panel indicator light.
The ESP offers exceptional
safety during normal driving,
but this should not encourage
the driver to take extra risks
(late braking) or drive at high speed.
Correct operation of the system depends
on compliance with the manufacturer's
recommendations regarding the wheels
(tyres and rims), the braking compo-
nents, the electronic components and
the PEUGEOT assembly and operation
procedures.
After an impact, have the system
checked by a PEUGEOT dealer. ANTI-LOCK BRAKING SYSTEM (ABS)
The ABS increases the stability and
manoeuvrability of your vehicle on
braking, in particular on poor or slip-
pery road surfaces.
This system comes into operation
automatically when there is a risk of
wheel lock.
Normal operation of the ABS may
make itself felt by slight vibrations of
the brake pedal.
This indicates that the ABS is
faulty.
It also comes on on the instru-
ment panel screen.
If it comes on permanently above
6 mph (10 km/h), it indicates an ABS
malfunction.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
EMERGENCY BRAKING ASSISTANCE SYSTEM
In an emergency, this system enables
the optimum braking pressure to be
reached more quickly, thus reducing
the stopping distance.
It is triggered by the speed at which
the brake pedal is activated.
The effect of this is a reduction in the
resistance of the pedal and an in-
c r e a s e i n b r a k i n g e f fi c i e n c y .
When braking in an emergency, press
fi r m l y w i t h o u t r e l e a s i n g t h e p r e s s u r e .
In emergency braking, press
v e r y fi r m l y w i t h o u t r e l e a s -
ing the pressure.
Note: when changing wheels (tyres
and rims), make sure that these are
approved.
Page 104 of 249
7SAFETY
89
The driver must ensure that
the passengers use the seat
belts correctly and that they
are all properly restrained be-
fore setting off.
Wherever you are seated in the vehi-
cle, always fasten your seat belt, even
for short journeys.
Do not invert the seat belt buckles as
t h e y w i l l n o t f u l fi l t h e i r r o l e f u l l y .
If the seats have armrests * , the lap
part of the seat belt must always pass
under the armrest.
T h e s e a t b e l t s a r e fi t t e d w i t h a n i n e r t i a
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stored automatically
when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
T h e i n e r t i a r e e l s a r e fi t t e d w i t h a n a u -
tomatic locking device which comes
into operation in the event of a colli-
sion, on emergency braking or if the
vehicle rolls over. You can release the
device by pulling rapidly on the strap
and releasing it. Recommendations for children:
- use a suitable child seat if the pas-
senger is less than 12 years old or
s h o r t e r t h a n o n e m e t r e fi f t y ,
- do not use the strap-guide * when a child seat is installed.
- never use the same seat belt to se- cure more than one person,
- never allow a child to travel on your lap.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags. Triggering of the pre-tensioners
is accompanied by a slight emission of
harmless smoke and a noise, due to
the activation of the pyrotechnic car-
tridge incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if necessary
replaced, by a PEUGEOT dealer.
* According to model.
In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking that
it does not twist,
- m u s t n o t b e t r a n s f o r m e d o r m o d i fi e d to avoid altering its performance.
In accordance with current safety reg-
ulations, all repairs and checks must
be carried out by a PEUGEOT dealer
who guarantees that the work is car-
ried out correctly.
Have your seat belts checked regularly
by a PEUGEOT dealer and particularly
if the straps show signs of damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt is
positioned and rolled up correctly.