lock Peugeot 407 2010 Service Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 407, Model: Peugeot 407 2010Pages: 249, PDF Size: 14.69 MB
Page 112 of 249
8DRIVING
Auto-adaptive programme
select position D in the gate: the
gearbox operates in auto-adaptive
mode, without any action on your
part, taking into account the follow-
ing parameters:
- the style of driving,
- t h e p r o fi l e o f t h e r o a d ,
- the vehicle load.
To obtain maximum acceleration with-
out touching the lever, press the ac-
celerator down fully (kick down). The
programme will change down auto-
matically or will stay in the gear select-
ed until the maximum engine speed is
reached.
When the brake is applied, the pro-
gramme will change down automati-
c a l l y i n o r d e r t o p r o v i d e e f fi c i e n t e n g i n e
braking. Sport and Snow programmes
These are two special programmes.
The programme selected is displayed
on the instrument panel screen.
It is only possible to change
from one gear to another if
the vehicle speed and engine
speed permit. If they do not,
the vehicle will operate temporarily in
automatic mode.
When the vehicle is stationary or mo-
ving very slowly, the gearbox automa-
tically selects gear M1 .
Programmes S (sport) and (snow)
do not operate in manual gear selec-
tion mode.
Any operating abnormality is
indicated by lighting of this
warning lamp, accompanied
by an audible signal and a
message on the multi-function
screen.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substantial
knock when changing from P to R and
from N to R (this will not cause any
damage to the gearbox).
Do not exceed 60 mph (100 km/h) and
keep within local speed limits.
Have it checked by a PEUGEOT dealer.
Operating check
Operation with manual
selection of the gears
select position M in the gate,
push the lever to the + sign to
change up a gear and push again
to change up another gear,
pull the lever to the - sign to change
down a gear and pull again to
change down another gear.
You can change from position D (driv-
ing in automatic mode) to position M
(driving in manual mode) at any time.
Releasing the accelerator
sharply does not have any im-
mediate effect on the speed of
the vehicle.
Never select position
N when
the vehicle is moving.
Never select positions P or R
unless the vehicle is stationary.
Never change between positions to
optimise braking on a slippery surface. Sport programme
Press button S once the vehicle
has been started in position D , the
auto-adaptive programme favours
dynamic driving.
Snow programme
This programme improves starting and
drive when traction is poor.
Press button once the vehicle
has been started and position D has
been selected, the auto-adaptive
programme adjusts the performance
of the vehicle to the condition of the
slippery road.
You can deactivate the Sport or Snow
programme at any time by pressing
the button selected.
I f t h e b a t t e r y i s fl a t a n d t h e l e -
ver is in position P , it will be
impossible to change to an-
other position.
In particular, do not force the lever
or there is a risk the gearbox may be
damaged.
Page 120 of 249
8DRIVING
104
Deactivation
Press button A to deactivate the sys-
tem (child asleep in the rear...). The in-
dicator lamp on the button comes on.
Note: this function will be de-
activated automatically when
a trailer is being towed (vehi-
c l e fi t t e d w i t h a t o w b a r r e c o m -
mended by PEUGEOT). If there is an operating fault,
when reverse gear is en-
gaged, the indicator lamp
fl a s h e s , a c c o m p a n i e d b y a n
audible signal and a message on the
multifunction screen.
Reactivation
Press button
A again to reactivate the
system. The indicator lamp on the but-
ton is switched off.
The proximity of the obstacle is indi-
cated by:
- an audible signal which becomes more rapid as the vehicle ap-
proaches the obstacle,
- a graphic on the multifunction screen, with blocks which become
increasingly close to the vehicle.
The obstacle is located in relation to
the emission of the audible signal by
the speakers; that is, front or rear and
right or left.
When the distance between the ve-
hicle and the obstacle is less than
approximately thirty centimetres, the
audible signal becomes continuous
and/or the "Danger" symbol appears
on the multifunction screen.
The system becomes inactive again:
- when you exit reverse gear,
- when the speed is above 6 mph (10 km/h),
- at the end of the manoeuvre, when stationary, after a few seconds
(front parking sensors only).
Page 132 of 249
1010PRACTICAL INFORMATION
116
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e
that the direction notches are po-
sitioned correctly and the securing
c l i p s a r e fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 - Direction indicators:
PY21W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF ELEC-
TROCUTION
Front lamps
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps: H1-55W
or D2S-35W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direc-
tion indicators and side re-
peaters) must be replaced
w i t h b u l b s o f i d e n t i c a l s p e c i fi -
cation and colour.
5 - Front foglamps: H11 - 55W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the other lamps and their surrounds
to avoid damaging their coating and
seals.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lighting is switched on.
3 - Sidelamps: W5W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 136 of 249
1010PRACTICAL INFORMATION
119
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box lighting, side repeaters, front and rear
courtesy lamps, map reading lamps, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control unit,
navigation-telematics (according to country).
Page 137 of 249
1010PRACTICAL INFORMATION
119
CHANGING A FUSE
The fuse boxes are placed in the lower
part of the fascia (passenger side in
the glove box) and in the engine com-
partment (left-hand side). Fascia fuses
To access the fuses, open the glove box. Open the fuse box co
ver by pressing the
two tabs at the top.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi e d . T h e f u s e n u m b e r s a r e i n d i c a t e d
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Use the special pliers located
on the support next to the fuse box,
this support also contains the replace-
ment fuses.
Fuse N°
Rating
A
Functions
F1 15 Rear wiper.
F2 30 Central locking/deadlocking.
F3 5 Air bags.
F4 10 ESP dual function sensor, diagnostic connector,
sunroof (Saloon), steering wheel angle sensor.
F5 30 Front one-touch electric windows, sunroof
( S a l o o n ) , p a n o r a m i c r o o f c o n c e a l i n g fl a p
(407SW).
F6 30 Rear one-touch electric windows.
F7 5 Glove box lighting, side repeaters, front and rear
courtesy lamps, map reading lamps, courtesy
mirror.
F8 20 Multifunction display, audio equipment, steering
wheel control, trailer fuse box, alarm control unit,
navigation-telematics (according to country).
Page 138 of 249
1010PRACTICAL INFORMATION
120
Fuse N°
Rating
A
Functions
F9 30 Lighter, telematics (according to country), rear 12 V accessories socket (100 W max).
F10 15 T y r e u n d e r - i n fl a t i o n d e t e c t i o n u n i t .
F11 15 Diagnostic socket, ignition switch.
F12 30 Hands-free kit, trailer socket, trailer fuse box, audible rear pa
rking assistance, passenger’s
electric seat, rain and brightness sensor, alarm.
F13 5 Engine fuse box, windscreen wipers relay control.
F14 15 Driver’s electric seat, instrument panel, air conditioning control panel, air bags control unit.
F15 15 Electric child lock, rear doors deadlocking.
F17 40 Heated rear screen.
FS1 - PARC shunt.
Page 141 of 249
1010PRACTICAL INFORMATION
122
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
r e fi t t h e b a t t e r y c o v e r w h e n y o u h a v e
fi n i s h e d .
Fuse N°
Rating
A
Functions
1 20 Engine management control unit.
2 15 Horn.
3 10 Front and rear wash-wipe.
4 20 Headlamp wash.
5 15 Engine management actuators (fuel pump,
purge canister solenoid valves, ...).
6 10 Automatic gearbox control unit.
7 10 S w i t c h i n g a n d p r o t e c t i o n u n i t , i n t a k e a i r fl o w
sensor, clutch switch, six-speed automatic gear-
box switch, STOP switches, electrochromatic
m i r r o r , p a n o r a m i c r o o f c o n c e a l i n g fl a p c o n t r o l s
(407SW).
8 20 Starter coil.
9 10 Xenon bulb electronic supply, STOP switch,
power steering electropump assembly, four-
speed automatic gearbox control unit, automatic
gearbox locking relay.
10 30 Engine management actuators (ignition coil,
solenoid valves, oxygen sensors).
11 40 Air conditioning blower or not used.
12 30 Windscreen wipers.
13 40 Built-in systems interface supply (ignition pos itive).
14 30 Air pump.
Page 144 of 249
1010PRACTICAL INFORMATION
124
To start the vehicle from another
battery:
- Connect the red cable to the positive (+) terminals of the two batteries,
- Connect one end of the green or black cable to the negative (-) ter-
minal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
- Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables.
BATTERY (LOCATED IN THE ENGINE COMPARTMENT)
Disconnecting/Reconnecting
the cables
1. Raise the locking plate A .
2. Position the open clip of the cable
on the positive (+) terminal of the
battery.
3. Press until the position checking
system B tilts.
4. Lock the clip by lowering the lock-
ing plate while pressing on the clip.
It is advisable to disconnect
the battery if the vehicle is not
to be used for a period of more
than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use giv-
en by the manufacturer the battery
charger,
- Reconnect starting with the nega- tive (-) terminal,
-
Check that the terminals and connec-
tors are clean. If they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
Do not force the plate as lock-
ing is not possible if the clip is
not positioned correctly.
Start the procedure again.
Page 178 of 249
159
11
2 2
3 3
4 4
11
2 2
3 3
4 4
AUDIO/VIDEO
RADIO
SELECTING A STATION
Press the SOURCE button several times in succession and select the RADIO.
Press the BAND button to select a waveband: FM1, FM2, FMast, AM.
B r i e fl y p r e s s o n e o f t h e b u t t o n s t o carry out an automatic search of the radio stations.
Press one of the buttons to carry out a manual search of the radio stations.
Press the LIST button to display the list of stations received locally (60 maximum). To update this list, press for more than two seconds.
The external environment (hills, buildings, tunnels, basement car parks, ...) may block reception, including in RDS mode. This is a normal effect of t he way in which radio waves are transmitted and doe s not indicate any failure of the audio equipment.
RDS
Select ACTIVATE FREQUENCY FOLLOWING (RDS) then press OK. RDS appears on the display.
Select the FM WAVEBAND PREFERENCES function then press OK.
Select AUDIO FUNCTIONS then press OK.
Press the MENU button.
The RDS, if displayed, enables you to continue lis tening to the same station by automatic retuning to alternative fequen cies. However, in certain conditions, coverage of an RDS station may not be assured throughout the country as radio stations do not cover 100 % of the territory. This explains the loss of reception of the station during a journey.
ACTIVATE FREQUENCY FOLLOWING (RDS)
FM WAVEBAND PREFERENCES
Page 200 of 249
181
QUESTION SOLUTION ANSWER
The environment (hills, buildings, tunnels, basement car parks...) block reception, including in RDS mode.
The aerial is absent or has been damaged (for exam ple when going through a car wash or into an underground car park).
This phenomenon is normal and does not indicate a failure of the audio equipment.
Have the aerial checked by a PEUGEOT dealer.
Sound cut-outs of 1 to 2 seconds in radio mode.
During this brief sound cut-out, the RDS searches for any frequency permitting better reception of the station. Deactivate the RDS function if the phenomenon is too frequent and always on the same route.
With the engine off, the audio equipment switches off after a few minutes of use.
When the engine is switched off, the audio equipme nt operating time depends on the battery charge.
The switch-off is normal: the audio equipment switches to economy mode and switches off to prevent discharging of the vehicle's battery.
The stored stations do not function (no sound, 87.5 Mhz is displayed...) .
An incorrect waveband is selected. Press the BAND AST button to return to the waveband (AM, FM1, FM2, FMAST) on which the stations are stored.
Start the vehicle's engine to increase the battery charge.
The quality of reception of the radio station listened to gradually deteriorates or the stored stations do not function (no sound, 87.5 Mhz is displayed...).
The vehicle is too far from the transmitter used by the station listened to or there is no transmitter in the geographical area th rough which the vehicle is travelling.
Activate the RDS function to enable the system to check whether there is a more powerful transmitter in the geographical area.