display Peugeot 407 C 2008 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C, Model: Peugeot 407 C 2008Pages: 211, PDF Size: 11.74 MB
Page 24 of 211
1
27
Coolant temperature indicator
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature
warning light comes on
(linked with the STOP warn-
ing light), stop immediately.
Wait for the engine to cool
down before topping up the level, if
necessary.
As the cooling circuit is pres-
surised, in order to prevent
any risk of scalding, unscrew
the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level with
coolant, if necessary.
Consult a PEUGEOT dealer.
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicator lights
Automatic gearbox fault
warning light
This indicates an automatic
gearbox fault.
The gearbox will operate in down-
grade mode, locked in 3rd gear.
Never force the selector lever.
Consult a PEUGEOT dealer.
6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol
, associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. "Manual" indicator lights
These correspond to the manual con-
trol of the gearbox.
When the engine speed is too low
or too high in relation to the gear en-
g a g e d , t h e g e a r s e l e c t e d fl a s h e s f o r
a few seconds, then the actual gear
is displayed, the auto-adaptive pro-
gramme having taken control tempo-
rarily.
Page 25 of 211
1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
n e r fl a s h .
Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
Page 26 of 211
1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule.
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
n e r fl a s h .
Example: when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example: when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
Page 27 of 211
1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y c h e c k -
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g i n d i -
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi v e m i n u t e s , o t h e r w i s e t h e
zero re-set will not be registered.
Page 28 of 211
1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service your-
self, the re-set procedure is as follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y c h e c k -
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g i n d i -
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi v e m i n u t e s , o t h e r w i s e t h e
zero re-set will not be registered.
Page 29 of 211
1
30
Trip recorder zero reset
With the trip distance displayed, press
the button for a few seconds.
Distance recorder
The total distance is displayed in zone
A of the display and the trip distance
in zone B .
LIGHTING RHEOSTAT
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or max-
imum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the
required brightness, release the button.
Page 30 of 211
1
31
TRIP COMPUTER
or
TRIP (Route): access
to the trip computer dis-
plays.
Zero reset
When the required route is displayed,
press the control for more than two
seconds. - the route
"1" tab with:
Page 31 of 211
1
32
Press the "MENU" button to gain ac-
cess to the general menu.
Select the "Trip computer" or
"Vehicle diagnostics" application us-
i n g t h e n a v i g a t o r , t h e n c o n fi r m o r p r e s s
the "MODE" button until you reach the
t r i p c o m p u t e r s c r e e n , t h e n c o n fi r m u s -
ing "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Warnings log,
- Status of the functions,
- Inputting of the distance to be trav- elled.
Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display on the instrument panel screen
All of the various items of trip computer
information also appear on the instru-
ment panel screen at the same time.
Distance remaining to be travelled (km or miles)
Average speed (km/h or mph)
Average consumption (l/100 or km/l or mpg)
Distance travelled (km or miles)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
This is the distance remaining to the
destination, either calculated at any
time by the navigation if guidance is
activated or entered by the user, mi-
nus the distance covered since the
distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to zero.
This indicates the distance travelled
since the computer was last set to zero.
Access via the general menu
"TRIP" (Route) menu
Page 32 of 211
2
33
COLOUR SCREEN C
This displays the following informa-
tion, via the WIP Sound audio system
control pad:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- t h e a c c e s s e s c h e c k ,
- the warning messages,
- the audio functions,
- the trip computer information,
-
t h e p e r s o n a l i s a t i o n a n d c o n fi g u r a t i o n
displays,
- the air conditioning parameters,
-
t h e f r o n t a n d r e a r p a r k i n g a s s i s t a n c e
display,
- t h e h a n d s - f r e e k i t d i s p l a y s . Management of the displays
General menu
Press the
"MENU" button to gain ac-
cess to the general menu and select
one of the following functions:
- "Audio functions",
- "Trip computer",
- " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n " ,
- "Air conditioning",
- " T e l e p h o n e " . " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
menu
This provides access to successive
c o n fi r m a t i o n w i n d o w s .
D e fi n i n g t h e v e h i c l e p a r a m e t e r s
This enables you to activate or de-
activate certain driving and comfort
elements:
-
"Automatic switching on of the lights", - "Follow-me-home lighting" and
"Duration",
- "Remote control action",
- " P e r m a n e n t l o c k i n g o f t h e b o o t " ,
- " D i r e c t i o n a l h e a d l a m p s " .
Example: "Automatic switching on of
the lights"
The
"AUDIO" , "TRIP" , "CLIM" and
"TEL" buttons on the RD4 audio
equipment control pad permit display-
i n g i n t h e m a i n w i n d o w .
Example: "TRIP"
Example: "Audio functions"
Page 33 of 211
2
34
S e l e c t i o n o f t h e l a n g u a g e
German, Spanish, French, English,
I t a l i a n , D u t c h , T u r k i s h , P o r t u g u e s e
a n d B r a z i l i a n P o r t u g u e s e .
C o n fi g u r a t i o n o f t h e d i s p l a y
- " S e t t i n g t h e b r i g h t n e s s - v i d e o " .
- " S e t t i n g t h e d a t e a n d t i m e " .
- " S e l e c t i o n o f t h e u n i t s " .
- " S e l e c t i o n o f t h e c o l o u r s " . Changing the date and time
From the
general menu , select the
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
i c o n u s i n g t h e n a v i g a t o r , t h e n c o n fi r m .
From the list displayed, select
" C o n fi g u r a t i o n o f t h e d i s p l a y " , then
c o n fi r m .
From the list displayed, select "Setting
the date and time" , t h e n c o n fi r m . Set the parameters one by one:
- the zone selected is displayed on
the screen,
- use the navigator to move from one zone to another,
- your new parameters are con- fi r m e d o n e b y o n e , b y p r e s s i n g t h e
navigator button,
- all of the changes are saved, if you c l i c k o n "OK" on the screen, or
cancelled, if you press the "ESC"
b u t t o n o n t h e c o n t r o l p a d .
F o r s a f e t y r e a s o n s , c o n fi g u r a -
tion of the multifunction dis-
plays by the driver must be
c a r r i e d o u t w h i l e s t a t i o n a r y .