light Peugeot 407 C 2008 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C, Model: Peugeot 407 C 2008Pages: 211, PDF Size: 11.74 MB
Page 20 of 211
1
23
Braking system warning
light
This indicates:
- handbrake applied or incorrectly released,
- a n e x c e s s i v e d r o p i n t h e b r a k e fl u - id level, in this case linked with the
STOP warning light,
- an electronic brake force distribu- tion malfunction, linked with the
STOP warning light.
WARNING LIGHTS WHICH ARE DISPLAYED ON THE INSTRUMENT PANEL
Seat belt warning light
When the ignition is switched
on, the warning light comes
on if a front occupant has not
fastened his seat belt or if he
unfastens it.
Fuel warning light
In certain driving conditions
and depending on the en-
gine, the distance which you
will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning light
This should switch off a few
seconds after the engine is
switched on.
When the engine is running, if the
w a r n i n g l i g h t fl a s h e s o r c o m e s o n c o n -
tinuously, this indicates an emission
control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Passenger air bag
disarmed warning light *
If the warning light remains
on, this indicates that the
passenger air bag has been
disarmed intentionally.
This warning light is re-
peated on the instrument
panel screen in the case
of the last 2 faults.
Stop immediately in the two latter
cases. Consult a PEUGEOT dealer. Anti-lock braking system
(ABS) warning light
If it comes on continuously
above 6 mph (10 km/h), it in-
dicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
This warning light is re-
peated on the instrument
panel screen.
Directional headlamps
warning light
W h e n t h i s fl a s h e s , i t i n d i -
cates a malfunction of the
directional headlamps.
Consult a PEUGEOT dealer. Diesel engine pre-heat
warning light
Wait for the warning light to
switch off before starting.
The duration of the display
is determined by the exterior
climatic conditions.
This warning light is re-
peated on the instrument
panel screen.
* According to country.
Page 21 of 211
1
24
T y r e u n d e r - i n fl a t i o n
warning light
This indicates that the tyre
pressure is too low.
A message on the multifunction display
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lights
Activation warning light
Operation warning light
Deactivation warning light
Malfunction warning light
Handbrake warning light
This indicates that the hand-
brake is still applied or has
not been released correctly.
It is linked with the braking system
warning light.
Low wash-wipe and
h e a d l a m p w a s h fl u i d l e v e l
warning light
When the wipers are switched
o n , t h i s i n d i c a t e s t h a t t h e fl u i d
level is too low.
Fill the wash-wipe and headlamp wash
fl u i d r e s e r v o i r .
Battery charge warning
light
When the engine is running,
this indicates a charging cir-
cuit malfunction (battery ter-
minals, alternator belt).
Consult a PEUGEOT dealer. Engine oil level warning
light
This indicates a low engine
oil level.
Stop immediately.
Consult a PEUGEOT dealer.
WARNING LIGHTS WHICH ARE DISPLAYED ON THE INSTRUMENT PANEL SCREEN
STOP warning light
It comes on linked with the
engine oil pressure, cool-
ant temperature, power
steering, braking system
or punctured tyre warning lights.
Stop immediately.
Consult a PEUGEOT dealer.
Low coolant level warning
light (according to
version)
This warning light indicates
a n i n s u f fi c i e n t c o o l i n g c i r c u i t
level.
Stop immediately.
Consult a PEUGEOT dealer.
Warning: the cooling circuit is pressu-
rised, wait for the engine to cool down
before topping up the level.
When topping up, and in order
to prevent any risk of scalding,
unscrew the cap by two turns
to allow the pressure to drop.
When the pressure has
dropped, remove the cap and top up
the level with coolant. Power steering warning
light
This indicates a power steer-
ing fault.
It is linked with the STOP warning light.
Consult a PEUGEOT dealer.
Page 22 of 211
1
25
T y r e u n d e r - i n fl a t i o n
detection system warning
light
This indicates the absence or
malfunction of one or more
tyre pressure sensors or a system fault.
Consult a PEUGEOT dealer.
Electronic engine
immobiliser warning light
This indicates an electronic
engine immobiliser system
malfunction.
Consult a PEUGEOT dealer. Front brake pads wear
warning light
This indicates that the brake
pads are worn.
For your safety, have them replaced
by a PEUGEOT dealer.
Fuel tank cap warning light
(according to version)
With the engine running, this
indicates that the fuel tank
cap is incorrectly secured or
absent.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h).
Door/boot open warning
light
With the engine running, this
indicates that an access has
not been closed correctly.
An illustration on the multifunction
d i s p l a y i d e n t i fi e s t h e a c c e s s ( e s ) c o n -
cerned.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above 6
mph (10 km/h). Air bags warning light
This indicates an air bag
fault.
Consult a PEUGEOT dealer.
Automatic headlamp
beam adjustment system
warning light
This indicates that the auto-
matic headlamp height ad-
juster is faulty.
Consult a PEUGEOT dealer.
Punctured tyre warning
light
This indicates that one or
more punctured tyres have
been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Engine oil pressure
warning light
This indicates that the engine
oil pressure is too low.
It is linked with the STOP warning
light.
Stop immediately if it comes on while
the engine is running.
If there is a lack of oil in the lubrication
circuit, top up the level and contact a
PEUGEOT dealer as soon as possible.
Page 23 of 211
1
26
Electronically controlled
suspension indicator
lights
This comes on when the
SPORT function is activated.
Automatic switching on of
the lights indicator light
This comes on when the
AUTO function is activated.
Automatic switching on
of the lights deactivation
indicator light
This comes on when the AUTO
function is deactivated.
Automatic wipers indicator
light
This comes on when the
AUTO function is activated.
Automatic wipers
deactivation indicator light
This comes on when the AUTO
function is deactivated.
Service warning light
This is displayed to indicate
an engine management sys-
tem fault.
Contact a PEUGEOT dealer as soon
as possible.
Electronically controlled
suspension fault warning
light
This indicates an electroni-
cally controlled suspension
malfunction.
Select automatic operation and con-
tact a PEUGEOT dealer as soon as
possible.
Obstacle proximity
detection system warning
light
In forward and/or reverse
gear, this indicates an obsta-
cle proximity detection system fault.
Consult a PEUGEOT dealer. This comes on when the
SPORT function is deacti-
vated.
P a r t i c l e e m i s s i o n fi l t e r
saturation warning light
(Diesel engine)
With the engine running, this
indicates that the particle
e m i s s i o n fi l t e r i s s t a r t i n g t o b e c o m e
saturated (exceptionally prolonged ur-
ban driving type conditions: low speed,
l o n g t r a f fi c j a m s . . . ) o r a l o w d i e s e l a d -
ditive reservoir level.
I n o r d e r t o r e g e n e r a t e t h e fi l t e r , y o u a r e
advised to drive, as soon as possible
w h e n t h e t r a f fi c c o n d i t i o n s p e r m i t , a t a
speed of 40 mph (60 km/h) or above
f o r a t l e a s t fi v e m i n u t e s ( u n t i l t h e w a r n -
ing light is switched off).
If the warning light remains on, contact
a PEUGEOT dealer.
Following prolonged use of the vehi-
cle at very low speeds or at idle, you
may, exceptionally, notice an emission
of water vapour at the exhaust during
acceleration. This does not affect the
performance of the vehicle or the en-
vironment. W a t e r i n d i e s e l fi l t e r
warning light
This indicates the presence
o f w a t e r i n t h e d i e s e l fi l t e r .
There is a risk of damage to
the injection system.
Contact a PEUGEOT dealer as soon
as possible.
Page 24 of 211
1
27
Coolant temperature indicator
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature
warning light comes on
(linked with the STOP warn-
ing light), stop immediately.
Wait for the engine to cool
down before topping up the level, if
necessary.
As the cooling circuit is pres-
surised, in order to prevent
any risk of scalding, unscrew
the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level with
coolant, if necessary.
Consult a PEUGEOT dealer.
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicator lights
Automatic gearbox fault
warning light
This indicates an automatic
gearbox fault.
The gearbox will operate in down-
grade mode, locked in 3rd gear.
Never force the selector lever.
Consult a PEUGEOT dealer.
6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol
, associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. "Manual" indicator lights
These correspond to the manual con-
trol of the gearbox.
When the engine speed is too low
or too high in relation to the gear en-
g a g e d , t h e g e a r s e l e c t e d fl a s h e s f o r
a few seconds, then the actual gear
is displayed, the auto-adaptive pro-
gramme having taken control tempo-
rarily.
Page 29 of 211
1
30
Trip recorder zero reset
With the trip distance displayed, press
the button for a few seconds.
Distance recorder
The total distance is displayed in zone
A of the display and the trip distance
in zone B .
LIGHTING RHEOSTAT
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or max-
imum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the
required brightness, release the button.
Page 32 of 211
2
33
COLOUR SCREEN C
This displays the following informa-
tion, via the WIP Sound audio system
control pad:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- t h e a c c e s s e s c h e c k ,
- the warning messages,
- the audio functions,
- the trip computer information,
-
t h e p e r s o n a l i s a t i o n a n d c o n fi g u r a t i o n
displays,
- the air conditioning parameters,
-
t h e f r o n t a n d r e a r p a r k i n g a s s i s t a n c e
display,
- t h e h a n d s - f r e e k i t d i s p l a y s . Management of the displays
General menu
Press the
"MENU" button to gain ac-
cess to the general menu and select
one of the following functions:
- "Audio functions",
- "Trip computer",
- " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n " ,
- "Air conditioning",
- " T e l e p h o n e " . " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
menu
This provides access to successive
c o n fi r m a t i o n w i n d o w s .
D e fi n i n g t h e v e h i c l e p a r a m e t e r s
This enables you to activate or de-
activate certain driving and comfort
elements:
-
"Automatic switching on of the lights", - "Follow-me-home lighting" and
"Duration",
- "Remote control action",
- " P e r m a n e n t l o c k i n g o f t h e b o o t " ,
- " D i r e c t i o n a l h e a d l a m p s " .
Example: "Automatic switching on of
the lights"
The
"AUDIO" , "TRIP" , "CLIM" and
"TEL" buttons on the RD4 audio
equipment control pad permit display-
i n g i n t h e m a i n w i n d o w .
Example: "TRIP"
Example: "Audio functions"
Page 35 of 211
2
36
D i s p l a y c o n fi g u r a t i o n
- "Choose colour",
- "Adjust brightness",
- "Adjust date and time",
- " S e l e c t u n i t s " . "Video" menu
D e fi n e t h e v e h i c l e p a r a m e t e r s
This enables you to activate or deacti-
vate certain driving and comfort func-
tions:
- "Automatic switching on of the
headlamps",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Directional headlamps",
- " P e r m a n e n t l o c k i n g o f t h e b o o t " .
Example: "Automatic switching on of
the headlamps"
You can connect video equipment
(camcorder, digital camera, DVD
p l a y e r , . . . ) t o t h e t h r e e v i d e o s o c k e t s , l
o c a t e d i n t h e g l o v e b o x .
V i d e o s c a n o n l y b e d i s p l a y e d w h e n
stationary.
Select the "Video" menu from the
general menu :
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the dis- play format, the brightness, the
c o n t r a s t a n d t h e c o l o u r s .
Pressing the "DARK" button discon-
n e c t s t h e d i s p l a y f r o m t h e v i d e o .
Successive presses on the "SOURCE"
button permit the selection of an audio
s o u r c e o t h e r t h a n t h a t o f t h e v i d e o .
F o r s a f e t y r e a s o n s , c o n fi g u r a -
tion of the multifunction dis-
p l a y s b y t h e d r i v e r m u s t t a k e
p l a c e w h e n s t a t i o n a r y .
Page 36 of 211
2
36
D i s p l a y c o n fi g u r a t i o n
- "Choose colour",
- "Adjust brightness",
- "Adjust date and time",
- " S e l e c t u n i t s " . "Video" menu
D e fi n e t h e v e h i c l e p a r a m e t e r s
This enables you to activate or deacti-
vate certain driving and comfort func-
tions:
- "Automatic switching on of the
headlamps",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Directional headlamps",
- " P e r m a n e n t l o c k i n g o f t h e b o o t " .
Example: "Automatic switching on of
the headlamps"
You can connect video equipment
(camcorder, digital camera, DVD
p l a y e r , . . . ) t o t h e t h r e e v i d e o s o c k e t s , l
o c a t e d i n t h e g l o v e b o x .
V i d e o s c a n o n l y b e d i s p l a y e d w h e n
stationary.
Select the "Video" menu from the
general menu :
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the dis- play format, the brightness, the
c o n t r a s t a n d t h e c o l o u r s .
Pressing the "DARK" button discon-
n e c t s t h e d i s p l a y f r o m t h e v i d e o .
Successive presses on the "SOURCE"
button permit the selection of an audio
s o u r c e o t h e r t h a n t h a t o f t h e v i d e o .
F o r s a f e t y r e a s o n s , c o n fi g u r a -
tion of the multifunction dis-
p l a y s b y t h e d r i v e r m u s t t a k e
p l a c e w h e n s t a t i o n a r y .
Page 39 of 211
3
40
AUTOMATIC AIR CONDITIONING (DUAL ZONE)
Dual zone: this is the differentiated
r e g u l a t i o n o f t h e t e m p e r a t u r e a n d a i r
distribution on the driver's side and the
f r o n t p a s s e n g e r s i d e .
T h e d r i v e r a n d h i s f r o n t p a s s e n g e r c a n
e a c h a d j u s t t h e t e m p e r a t u r e a n d t h e
d i s t r i b u t i o n o f t h e a i r t o s u i t t h e i r r e -
quirements.
T h e s y m b o l s a n d m e s s a g e s a s s o c i a t -
ed with the automatic air conditioning
c o n t r o l s a p p e a r o n t h e m u l t i f u n c t i o n
d i s p l a y .
Control by the Auto programme Automatic
programme - driver
and passenger
comfort (1)
Press the "AUTO" b u t t o n . T h e i n d i c a -
tor light comes on. The "AUTO" s y m -
b o l i s d i s p l a y e d o n t h e m u l t i f u n c t i o n
d i s p l a y .
Adjustment of the
temperature on the
driver's side (2)
Adjustment of the temperature
on the passenger side (3)
P r e s s t h e u p o r d o w n a r r o w t o
c h a n g e t h e t e m p e r a t u r e o n t h e
driver's side 2 o r p a s s e n g e r s i d e 3 .
T h e v a l u e i n d i c a t e d o n t h e d i s p l a y c o r -
r e s p o n d s t o a l e v e l o f c o m f o r t a n d n o t
t o a t e m p e r a t u r e i n d e g r e e s C e l s i u s o r
F a h r e n h e i t , d e p e n d i n g o n t h e c h o i c e o f
c o n fi g u r a t i o n v a l i d a t e d o n t h e d i s p l a y .
A setting around the value 21 makes
i t p o s s i b l e t o o b t a i n o p t i m u m c o m f o r t .
H o w e v e r , d e p e n d i n g o n y o u r r e q u i r e -
ments, a setting between 18 and 24
is usual.
D e p e n d i n g o n t h e l e v e l o f c o m f o r t s e l e c t e d ,
t h e s y s t e m c o n t r o l s t h e a i r d i s t r i b u t i o n , fl o w ,
t e m p e r a t u r e a n d i n t a k e o f a i r i n o r d e r t o
g u a r a n t e e c o m f o r t a n d a n a d e q u a t e c i r c u -
l a t i o n o f a i r i n t h e p a s s e n g e r c o m p a r t m e n t .
Y o u d o n o t h a v e t o m a k e a n y a d j u s t m e n t s .
When the engine is cold, to
p r e v e n t t o o g r e a t a d i s t r i b u t i o n
of cold air, the ventilation will
o n l y r e a c h i t s o p t i m u m l e v e l
p r o g r e s s i v e l y .