ignition Peugeot 407 C Dag 2008 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C Dag, Model: Peugeot 407 C Dag 2008Pages: 211, PDF Size: 11.75 MB
Page 72 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 73 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 74 of 211
4
67
M a k e a c a r e f u l n o t e o f t h e
n u m b e r o n e a c h k e y . T h e
k e y n u m b e r i s c o d e d o n t h e
l a b e l a t t a c h e d t o t h e k e y .
If the keys are lost, a PEUGEOT
d e a l e r c a n r a p i d l y s u p p l y y o u w i t h
n e w k e y s .
T h e h i g h f r e q u e n c y r e m o t e c o n t r o l i s
a sensitive system; do not operate it
w h i l e i t i s i n y o u r p o c k e t a s t h e r e i s
a p o s s i b i l i t y t h a t i t m a y u n l o c k y o u r
v e h i c l e , w i t h o u t y o u b e i n g a w a r e o f i t .
The remote control does not oper-
a t e w h e n t h e k e y i s i n t h e i g n i t i o n ,
e v e n w h e n t h e i g n i t i o n i s s w i t c h e d
o f f , e x c e p t f o r r e p r o g r a m m i n g .
Do not operate the deadlocking
f u n c t i o n i f t h e r e i s a n y o n e i n s i d e
t h e v e h i c l e .
D r i v i n g w i t h t h e d o o r s l o c k e d m a y
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
A s a s a f e t y p r e c a u t i o n ( w i t h c h i l -
dren on board), remove the ignition
k e y w h e n y o u l e a v e t h e v e h i c l e ,
e v e n f o r a s h o r t t i m e .
D o n o t r e p e a t e d l y p r e s s t h e b u t t o n
o f y o u r r e m o t e c o n t r o l o u t o f r a n g e
a n d o u t o f s i g h t o f y o u r v e h i c l e .
Y o u r u n t h e r i s k o f s t o p p i n g i t f r o m
w o r k i n g a n d t h e r e m o t e c o n t r o l
w o u l d h a v e t o b e r e p r o g r a m m e d .
W h e n p u r c h a s i n g a s e c o n d - h a n d
vehicle, have the key codes memo-
rised by a PEUGEOT dealer to
e n s u r e t h a t t h e k e y s i n y o u r p o s -
s e s s i o n a r e t h e o n l y o n e s w h i c h
c a n s t a r t t h e v e h i c l e .
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the electronic engine immobiliser
s y s t e m .
Page 75 of 211
4
68
THE ALARM
This provides two types of surveil-
lance:
- exterior protection: it sounds if
a door, the boot or the bonnet is
opened.
-
interior protection: it sounds if the
volume inside the passenger compart-
ment changes (breaking of a window
or a movement inside the vehicle).
When the alarm is triggered, the si-
ren sounds and the direction indica-
t o r l i g h t s fl a s h f o r a p p r o x i m a t e l y t h i r t y
seconds.
After triggering, the alarm remains set,
ten times in succession.
On the eleventh time it will become
inactive again, until the next cycle of
disarming then setting of the alarm.
Warning: if button A indicator light
fl a s h e s r a p i d l y , t h e a l a r m h a s b e e n
triggered while you were away from
your vehicle.
Incorrect operation
When the ignition is switched on, if
button A lights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
R e m o t e c o n t r o l f a i l u r e , alarm set
Unlock the doors with the key and
open the door. The alarm is trig-
gered.
Switch on the ignition. The alarm is
disarmed.
* According to country.
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm, by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once per second).
If you wish to lock or deadlock your
vehicle without setting the alarm, lock
it (one turn of the key) or deadlock it
( a s e c o n d t u r n w i t h i n fi v e s e c o n d s
maximum) using the lock.
The alarm is activated automatically
two minutes after the last closure of a
door or the boot.
In order to avoid accidental triggering
of the alarm when a door or the boot
is opened, it is essential to press the
unlocking button on the remote control
again.
Before setting the alarm, en-
sure that all of the accesses
(doors, bonnet, boot) are
closed correctly.
Disarming
Unlock the vehicle with the remote
control key.
The alarm is disarmed, indicator light A
goes out when the ignition is switched on.
T o s e t t h e a l a r m w i t h e x t e r i o r protection only
If, while you are away from the vehi-
cle, you wish to leave a window par-
tially open or a pet inside the vehicle,
you should choose exterior protection
only.
Switch off the ignition,
In the next ten seconds, press but-
ton A until the indicator light is on
continuously,
Get out of the vehicle,
Set the alarm by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once a second).
Page 76 of 211
4
69
ELECTRIC WINDOWS
1 . D r i v e r ' s e l e c t r i c w i n d o w s w i t c h .
2 . P a s s e n g e r ' s e l e c t r i c w i n d o w
s w i t c h . A u t o m a t i c o p e r a t i o n :
To open or close the window, press or
pull the switch fully: the window opens
or closes completely when the switch
is released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one min-
ute after the key has been removed
from the ignition.
Once this time has elapsed, the electric
windows will not operate. To reactivate
them, switch the ignition on again.
S a f e t y a u t o - r e v e r s e
When the window rises and meets an
obstacle, it stops and immediately par-
tially lowers again.
In the event of unwanted opening
of the window on closing, press the
switch until the window opens com-
pletely, then pull the switch immediate-
ly until the window closes. Continue to
hold the switch for approximately one
second after the window has closed.
The safety auto-reverse function is not
active during this operation.
REINITIALISATION OF THE WINDOWS
Following reconnection of the bat-
tery, the safety auto-reverse function
must be reinitialised: the safety auto-
reverse function is not active during
these operations.
- with the door closed, lower the win-
dow completely, then raise it, it will
rise in steps of a few centimetres
each time the switch is pressed.
Repeat the operation until the win-
dow closes completely,
- continue to press the switch for at least one second after reaching
this position, window closed.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the windows, you must
reverse the movement of the window.
To do this, press the switch concerned.
When the driver operates the passen-
ger electric window switch, he must
ensure that no one is preventing cor-
rect closing of the window.
The driver must ensure that the pas-
sengers use the electric windows cor-
rectly.
Be aware of children when operating
the windows.
M a n u a l o p e r a t i o n :
To open or close the window, press or
pull the switch gently. The window stops
as soon as the switch is released
.
Page 80 of 211
4
72
SUNROOF
To tilt the roof: press and hold part A
of the switch.
To open the roof in sliding mode: tilt
the sunroof, then press part A of the
s w i t c h b r i e fl y .
To close it in sliding mode: press
part B o f t h e s w i t c h b r i e fl y .
To close it in tilt mode: press and
hold part B of the switch.
S a f e t y a u t o - r e v e r s e
When the sunroof is sliding closed and
meets an obstacle, it stops then par-
tially opens again. Pressing the locking button
on the remote control key for
more than 2 seconds closes
the sunroof in sliding mode.
The sunroof remains tilted.
To close the sunroof completely, press
and hold part B of the switch before
getting out of the vehicle.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
Always ensure that the sunroof
is closed correctly before leaving the
vehicle.
In the event of contact during closing in
tilt mode, you must reverse the move-
ment of the roof. To do this, press the
switch concerned.
When the driver closes the roof in tilt
mode, he must ensure that no one is
preventing correct closing of the roof.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Notes:
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), press and hold part
B
of the switch, w i t h i n t h e t w o s e c o n d s
which follow the triggering of the safety
auto-reverse, until the sunroof closes
completely.
Following reconnection of the bat-
tery or in the event of a malfunction,
press and hold part B of the switch,
the sunroof slides "step by step" until
it closes. Continue to press the switch
for approximately one second after
closing.
T h e s a f e t y a u t o - r e v e r s e f u n c t i o n i s
n o t a c t i v e d u r i n g t h e s e o p e r a t i o n s . S h u t t e r
The sunroof shutter is manual.
To open it, slide it rearwards using the
handle.
To close it, slide it forwards using the
handle.
D o n o t o p e n t h e s u n r o o f i m m e d i a -
t e l y a f t e r a s h o w e r o r i m m e d i a t e l y
a f t e r w a s h i n g t h e c a r .
Page 82 of 211
5
74
LIGHTS STALK
Lights off
Side lights Dipped/main beam head-
lamps Lights on
With the ignition and the automatic
lights function switched off, on open-
ing the driver's door a buzzer sounds
to warn you that you have left your
lights on.
Front and rear fog lamps (ring B)
Turn ring B forwards to switch on
and backwards to switch off. The
p o s i t i o n i s c o n fi r m e d b y t h e l i g h t
on the instrument panel.
Front fog lamps (one press)
These operate with the side lights, dipped
headlamps or main beam headlamps. Rear fog lamps (two presses)
These operate with the side lights and
the front fog lamps, or with the dipped
or main beam headlamps.
Left: downwards.
Right: upwards
D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
If you forget to return the di-
rection indicator to its normal
position, the volume of the au-
dible signal will increase, if you
are driving at a speed greater
than 45 mph (70 km/h).
Parking lights *
The side lights are lit on the side the
t r a f fi c i s o n f o r a f e w h o u r s .
With the engine switched off and with-
in 45 seconds maximum, place the in-
d i c a t o r l i g h t s s t a l k o n t h e t r a f fi c s i d e
(for example: for parking on the right;
switching on of the lights on the left).
This is indicated by an audible sig-
nal and lighting of the corresponding
direction indicator on the instrument
panel for a few seconds.
If the parking lights are activat-
ed when your vehicle switches
to economy mode, they will re-
main on. However, you cannot
activate the parking lights if your ve-
hicle is already in economy mode.
Dipped/main beam change
Pull the stalk fully towards you.
* According to version.
Automatic switching on of
the lights.
In the case of vehicles which
a r e n o t fi t t e d w i t h a l i g h t s s t a l k
with the "AUTO" position,
you can deactivate or activate
the automatic lighting via the multi-
function display "Personalisation-
C o n fi g u r a t i o n " menu.
Front and rear lights (ring A)
Turn ring A to the position re-
quired
Page 83 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation
Deactivation When this function is activa-
ted, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 84 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation
Deactivation When this function is activa-
ted, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.
Page 86 of 211
5
77
WINDSCREEN WIPER STALK
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.
A u t o m a t i c w i n d s c r e e n w i p e r
The automatic wiping is controlled by a
r a i n s e n s o r , fi t t e d o n t h e w i n d s c r e e n .
In AUTO mode, the wipers operate
automatically and a d j u s t t h e i r s p e e d
t o t h e i n t e n s i t y o f t h e r a i n f a l l .
Activation Deactivation
This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in AUTO
mode. This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver moves the
wipers stalk to position
I , 1
or 2 .
I n t h e e v e n t o f a m a l f u n c t i o n , the
driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Do not cover the rain sensor,
located on the windscreen
behind the interior mirror.
When using a car wash, switch off the
ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather,
position the blades at the top of the
windscreen (maintenance position) to
prevent the accumulation of snow.
T h e w i p i n g m u s t b e r e a c t i -
vated if the ignition has been
switched off for more than one
minute . Manual operation of the wipers stalk
by moving the lever
A up and return-
ing it to position "0" cancels the AUTO
position, the deactivation warning light
comes on on the instrument panel dis-
play accompanied by a message on
the multifunction display.
W i n d s c r e e n w i p e r s
2 Fast wipe (heavy rain).
1 Normal wipe
(moderate rain).
I Intermittent wipe
0 Off
AUTO
Automatic wipe then single
sweep.