warning light Peugeot 407 C Dag 2008 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C Dag, Model: Peugeot 407 C Dag 2008Pages: 211, PDF Size: 11.75 MB
Page 102 of 211
7
89
In the event of a malfunction
If this warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags may
no longer be deployed in the event of
a serious impact. Instrument panel warning light.
Disarming the front passenger's front air bag *
To ensure the safety of your child,
it is essential to disarm the pas-
senger air bag when you install a
rear- facing child seat on the front
passenger seat. Otherwise, the
child would risk being seriously in-
jured or killed if the air bag were to
i n fl a t e .
With the ignition switched off, in-
sert the key into the passenger air
bag disarming switch, turn it to the
"OFF" position, then remove the
key keeping the slot in this position. Reactivation
As soon as the child seat is removed,
turn the air bag slot to the
"ON" posi-
tion to re-activate the air bag and thus
ensure its safety function.
* According to country. When the ignition is on, this
warning light remains lit on
the instrument panel for the
duration of disarming.
In the "OFF" position, the passen-
ger air bag will not be triggered in the
event of an impact. The steering column air bag protects
the driver's knees in the event of a
serious front impact.
It is incorporated in the fascia below
the steering column.
Steering column air bag
Activation
It is deployed at the same time as the
front air bags.
Page 105 of 211
8
94
When maintenance opera-
tions need to be carried out
with the engine running, apply
the handbrake and select the
P ark position. Sport and Snow programmes
These are two special programmes.
The programme selected is displayed
on the instrument panel screen. It is only possible to change
from one gear to another if
the vehicle speed and engine
speed permit. If they do not,
the vehicle will operate temporarily in
automatic mode.
When the vehicle is stationary or
moving very slowly, the gearbox auto-
matically selects gear M1 .
Programmes S (sport) and (snow)
do not operate in manual gear selec-
tion mode.
Any operating abnormality is
indicated by lighting of this
warning light, accompanied
by an audible signal and a
message on the multi-func-
tion display.
In this situation the gearbox operates in
downgrade mode (locked in 3rd gear).
You may feel a substantial knock when
changing from P to R and from N to R
(this will not cause any damage to the
gearbox).
Do not exceed 60 mph (100 km/h) or
keep within local speed limits.
Contact a PEUGEOT dealer as soon
as possible.
Operating check
Operation with manual selection of the gears
select position M in the gate,
push the lever to the + sign to
change up a gear and push again
to change up another gear,
pull the lever to the - sign to change
down a gear and pull again to
change down another gear.
You can change from position D
(driving in automatic mode) to posi-
tion M (driving in manual mode) at any
time.
The auto-adaptive programme
select position D in the gate: the
gearbox operates in auto-adap-
tive mode, without any action on
your part, taking into account the
following parameters:
- the style of driving,
- t h e p r o fi l e o f t h e r o a d ,
- the vehicle load.
To obtain maximum acceleration
without touching the lever, press the
accele rator down fully (kick down).
The programme will change down
automatically or will stay in the gear
selected until the maximum engine
speed is reached.
When the brake is applied, the pro-
gramme will change down automati-
c a l l y i n o r d e r t o p r o v i d e e f fi c i e n t e n g i n e
braking. Sport programme
Press button S once the vehicle
has been started in position D , the
auto-adaptive programme favours
dynamic driving
Snow programme
This programme improves starting and
drive when traction is poor.
Press button once the vehicle
has been started and position D
has been selected, the auto-adap-
tive programme adjusts the perfor-
mance of the vehicle to the condi-
tion of the slippery road.
You can deactivate the Sport or Snow
programme at any time by pressing
the button selected.
Releasing the accelerator
sharply does not have any im-
mediate effect on the speed of
the vehicle.
Never select position N when
the vehicle is moving.
Never select positions P or R
unless the vehicle is stationary.
Never change between positions to
optimise braking on a slippery sur-
face. I f t h e b a t t e r y i s fl a t a n d t h e
lever is in position
P , it will
be impossible to change to
another position.
In particular, do not force the lever
or there is a risk the gearbox may be
damaged.
Page 106 of 211
8
95
Press switch 1 , the indi-
cator light comes on and
the SPORT warning light
comes on.
Manual selection of the SPORT
position
Press switch 1 again. The
indicator light is switched
off and the AUTO indica-
tor light comes on.
To return to automatic operation
In this position, the suspension is
maintained in the
SPORT position.
In the event of a fault, it
comes on, accompanied by
an audible signal and a mes-
sage on the multifunction
display.
Select automatic operation and contact
a PEUGEOT dealer as soon as possible.
Operating check
T h i s i s c o n fi r m e d b y t h e s w i t c h l i g h t
and the indicator lights.
ELECTRONICALLY CONTROLLED SUSPENSION
The suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving
the comfort of the occupants and the
vehicle's road holding capabilities. The
suspension favours smooth shock
absorption, ensuring a comfortable
ride, but as soon as conditions demand
a change (sporty driving, tight bends,
avoidance action, etc.) it automatically
s e l e c t s fi r m e r s h o c k a b s o r p t i o n , g u a r a n -
teeing optimum road holding.
Page 113 of 211
8
102
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Pressure Check With the ignition on and the
vehicle having been stationary
for approximately 15 minutes,
and after the engine oil level,
this indicator light comes on
on the instrument panel screen to indi-
cate that the system is measuring the
tyre pressures.
Pressure OK
This indicator light comes
on on the instrument panel
screen if all of the tyre pres-
sure values measured are
correct.
If this indicator light does not appear,
contact a PEUGEOT dealer to have
the system checked. Puncture
This warning light, accom-
panied by the audible signal
and the message on the
multi-function display loca-
ting the wheel concerned, is
followed by illumination of the STOP
warning light.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d h a v e
the tyre pressure checked as soon as
possible.
Note: this message is also dis-
played when one of the wheels
is away from the vehicle (be-
ing repaired) or when one or
more wheels without a sensor
a r e fi t t e d . All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system
reinitialised by a PEUGEOT dealer.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate the
need to have the tyre pressure checked
regularly (see manufacturer's label) to
ensure that the optimum dynamic per-
formance of the vehicle is maintained
and prevent premature wear of the
tyres, particularly in arduous driving
conditions (heavy load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remember
to check the pressure of the spare
wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem may experience temporary inter-
ference due to radioelectric emissions
on a frequency close to that used by
the system.
Flat tyre
This warning light is accom-
panied by the audible si gnal
and the message on the
multi-function display loca-
ting the wheel concerned.
If this warning light comes on, have
the tyre pressure checked as soon as
possible. Sensor(s) not detected or faulty
This warning light is accom-
panied by the audible si gnal
and the message on the
multi-function display which
i n d i c a t e s t h a t u n d e r - i n fl a t i o n
detection is absent from one (or seve-
ral) wheel(s) or that there is a fault in
the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Page 122 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l s p a r e
w h e e l , w h e n fi t t i n g i t , i t i s normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essential
to use special bolts available from your
PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a Peugeot dealer.
You are advised to do the same for
the duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
Page 123 of 211
1010
111
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the trims
before slackening the bolts.
Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l s p a r e
w h e e l , w h e n fi t t i n g i t , i t i s normal when
tightening the bolts to notice that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone shape of each bolt.
VERY COLD CLIMATE SCREEN *
The very cold climate screen is a par-
t i a l r e m o v a b l e c o v e r w h i c h i s fi x e d
onto the air intake grille to prevent the
accumulation of snow due to direct
splashes.
O n c e i t h a s b e e n fi t t e d o n y o u r v e h i -
cle, it is imperative that it is removed
when the ambient temperature condi-
tions rise above 10°C again.
Consult a PEUGEOT dealer.
* According to country.
Special features of alloy wheels
Anti-theft bolts
Y o u r w h e e l s a r e fi t t e d w i t h a n t i - t h e f t
bolts (one per wheel), placed under
chrome trims which must be removed
using the yellow tool, before the bolts
are unscrewed using the anti-theft
socket and the wheel brace 1 .
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is
essential
to use special bolts available from your
PEUGEOT dealer.
Note: this anti-theft socket
was given to you on delivery
of your vehicle with the dupli-
cate keys. Make a careful note
of the code number engraved on the
head of the anti-theft socket. This will
enable you to obtain a duplicate anti-
theft socket from a Peugeot dealer.
You are advised to do the same for
the duplicate keys and not to leave the
c o n fi d e n t i a l c a r d i n t h e v e h i c l e .
Punctured tyre warning
light
Information on the instrument
panel:
T y r e u n d e r - i n fl a t i o n
detection system warning
light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
Page 124 of 211
1010
112
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Side lights: W 5 W (COOL BLUE
®).
Turn the access cap a quarter turn,
remove the bulb and change it.
3 - Direction indicators:
PY 21 W (DIADEM
®).
Turn the access cap a quarter turn,
Remove the bulb holder.
Change the bulb.
4 - Front fog lamps: H11 - 55 W.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abrasive
cloth, nor with a detergent or solvent
product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality. Integrated direction indicator side
repeaters
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from a
PEUGEOT dealer.
Front lights
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam and main beam headlamps: D1S - 35 W xenon bulb.
WARNING: RISK OF
ELECTROCUTION Coloured bulbs (side lights
and direction indicators) must
be replaced with bulbs of iden-
t i c a l s p e c i fi c a t i o n a n d c o l o u r .
In certain climatic conditions
(low temperature, humidity),
condensation on the inside
surface of the headlamp glass
is normal; it disappears a few minutes
after the lights are switched on.
Xenon bulbs must be replaced by a
PEUGEOT dealer.
Page 135 of 211
1010
122
In all cases, pay attention to the coolant
temperature.
Brakes: towing increases the braking
distance. Drive at a moderate speed,
change down early and brake gradually.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. TOWING A TRAILER, CARAVAN, BOAT, ETC...
We recommend the use of original
PEUGEOT towbars which have been
tested and approved from the design
stage of your vehicle and that the tow-
b a r i s fi t t e d b y a P E U G E O T d e a l e r .
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heavi-
est loads are as close as possible to
the axle and the nose weight is close
to the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope in-
creases the coolant temperature.
As the fan is electrically controlled, its
cooling capacity is not dependent on
the engine speed.
Note: in certain cases of par-
ticularly arduous use (towing
the maximum load in high
temperatures), the engine au-
tomatically limits its power and selects
the appropriate automatic gearbox
gear in manual mode. In this case,
cutting off the air conditioning allows
the engine power to be recovered, and
therefore the towing capacity to be in-
creased.
If the coolant temperature
warning light comes on, stop
the vehicle and switch off the
engine as soon as possible.
Tyres: check the tyre pressures of the
towing vehicle (label on the central
door pillar on the driver's side) and of
the trailer towed, observing the recom-
mended pressure.