spare wheel PEUGEOT 5008 2020 Owner's Manual

197
In the event of a breakdown
8Putting the wheel back in place

► Put the wheel back in its housing.
► Slacken the nut on the bolt by a few turns.
►

Position the fixing parts (nut and bolt) in the
middle of the wheel.


► Tighten fully until the central nut clicks, to
retain the wheel correctly.
►

Return the tool box to the middle of the wheel
and clip it in place.
Accessing the spare wheel



The spare wheel is held by a winch system
underneath the rear of the vehicle.
Only a "space-saver" type spare wheel
may be fixed underneath the vehicle.
Removing the spare wheel

► Fold back the concertina panel and install
the third row seat, on the left-hand side (if your
vehicle is equipped with it).
►

Lift the pre-cut section of carpet to release
the spare wheel

fixing winch nut.
►

With extension piece 8

placed on the end
of wheelbrace 5, "tighten" the nut to unreel the
winch cable until the spare wheel is flat on the
ground. Unreel as much as necessary in order to
access the wheel easily.

198
In the event of a breakdown

► Remove the wheel/box unit through the back
of the vehicle.
►

Straighten the spare wheel to access the tool
box (

A).


► Detach the connecting piece from the cover
of the tool box ( B - C).
►

Pass the connecting piece through the wheel
hub to release it ( D

).
Storing the tools

► Replace the appropriate tools in the box and
close the cover again.
►

Place the tool box on the ground.
►


Insert the connecting piece into the tool box
hole (

B - C).
►

Reel in the winch by loosening the winch
control nut with wheelbrace 5

and extension
piece 8: once the cable is completely reeled in,
you should no longer feel any resistance.
►

Store the rest of the tools in the storage
areas in the boot sill trim.
The punctured wheel cannot be stored beneath the vehicle.
It must be stored in the boot. Use a cover to
protect the interior of the boot.
Putting the winch and spare wheel
back in place


► Place the appropriate tools in the box and
close the cover again.
►

Place the tool box on the ground.
When the spare wheel is fitted in place of
a wheel with a punctured tyre, the winch
and tool box must be placed beneath the
vehicle again before restarting.

199
In the event of a breakdown
8► Straighten the wheel.
► Pass the connecting piece through the wheel
hub (
A).


► Insert the connecting piece into the tool box
hole ( B - C).
►

Centre and position the spare wheel on the
tool box (

D).


► Insert the centering guide into the wheel hub.
► Place the wheel/box unit beneath the rear of
the vehicle.


► Raise the wheel/box unit underneath the
vehicle, by "loosening" the winch control nut with
wheelbrace 5
and extension piece 8.
►

T
ighten it fully. When the cable is completely
reeled in, turning the nut no longer encounters
resistance.
►

Check that the wheel is properly flattened
against the floor

.
Removing a wheel
Wheel with wheel trim
When removing the wheel , first remove
the wheel trim by pulling at the valve aperture
using the wheelbrace.
When refitting the wheel , refit the wheel
trim, starting by placing its aperture in line
with the valve and then pushing it into place
all round its edge with the palm of your hand.
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear
to lock the wheels, apply the parking brake,
unless it is programmed to be in automatic
mode, and switch off the ignition.
With an automatic gearbox, select mode

P

to lock the wheels, apply the parking brake,
unless it is programmed to be in automatic
mode, and switch off the ignition.
Check for the fixed illumination of the parking
brake warning lamps in the instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
If necessary, place a chock under the wheel
diagonally opposite the wheel to be changed.
Never go underneath a vehicle raised using a
jack; use an axle stand.

200
In the event of a breakdown

► To remove the wheel bolt cover on each of
the bolts, use tool 7 (alloy wheels).
►

Fit security socket
2 on wheelbrace
5
to
slacken the security bolt.
►

Slacken the other bolts using the
wheelbrace


5
only.


► Place the foot of jack 6 on the ground and
ensure that it is directly below the front A or
rear
B jacking point on the underbody, whichever
is closest to the wheel to be changed.


► Extend jack 6 until its head comes into
contact with jacking point A or B; contact area A
or B on the vehicle must be properly inserted
into the central part of the head of the jack.
►

Raise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily

.
Ensure that the jack is stable. If the
ground is slippery or loose, the jack may
slip or collapse - risk of injury!
Take care to position the jack strictly at
one of the jacking points

A
or B under the
vehicle, ensuring that the head of the jack is
centred under the contact area of the vehicle.
Otherwise, there is a risk of damage to the
vehicle and/or of the jack collapsing - risk of
injury!


► Remove the bolts and store them in a clean
place.
►

Remove the wheel.
Fitting a wheel

Fitting a steel or ‘space-saver’ type
spare wheel
If the vehicle is equipped with alloy wheels,
the washers do not make contact with the
steel or ‘space-saver’ type spare wheel. The
wheel is secured by the conical surface of
each bolt.


► Fit the wheel on the hub.
► Screw in the bolts by hand as far as possible.
►

Pre-tighten the security bolt using the
wheelbrace


5
equipped with a security socket
2
.
►

Pre-tighten the other bolts using the
wheelbrace


5
only.

201
In the event of a breakdown
8

► Lower the vehicle again fully.
► Fold jack 6 and remove it.


► Tighten the security bolt using the
wheelbrace 5 equipped with a security socket 2 .
►

T
ighten the other bolts using the
wheelbrace

5
only.
►

Refit the bolt covers to each of the bolts
(depending on equipment).
►


Store the tools.
After changing a wheel
Store the punctured wheel in the boot or,
depending on version, remove the central cover
first to store it beneath the floor in place of the
spare wheel.


With a "space-saver" type spare wheel
Deactivate certain driving aid functions
(Active Safety Brake, Adaptive cruise control,
etc.).
Do not exceed the maximum authorised
speed of 50 mph (80
km/h).
Driving with more than one “space-saver”
type spare wheel is prohibited.
Visit a PEUGEOT dealer or a qualified
workshop as soon as possible to have
the tightness of the bolts and the pressure of
the spare wheel checked.
Have the punctured tyre examined. After
inspection, the technician will advise you on
whether the tyre can be repaired or if it must
be replaced.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), misting on the
internal surface of the glass of the headlamps
and rear lamps is normal, and will disappear
after the lamps have been on for a few
minutes.
The headlamps have polycarbonate lenses with a protective coating:
–

Do not clean them with a dry or abrasive
cloth, nor with detergent or solvent
products.
–


Use a sponge and soapy water or a pH
neutral product.
–


When using a high-pressure washer on
persistent marks, do not keep the lance
directed towards the headlamps, lamps or
their edges for too long, so as not to damage
their protective coating and seals.
Changing a bulb must only be done with
the ignition off and after the headlamp /
lamp has been switched off for several
minutes - risk of serious burns!
Do not touch the bulb directly with your
fingers; use a lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.

285
Alphabetical index
Tailgate 36
Tank, fuel
166–167
Technical data

220, 222, 225
Telephone

67, 234–237, 248–250, 271–273
Telephone, Bluetooth with voice recognition

237
Temperature, coolant

18
Textured Paint

188
Thermal preconditioning of the passenger
compartment

27, 65
Ticket holder

66
Time (setting)

23–24, 251, 275
TMC (Traffic info)

262
Tool box

76
Tools

191–193, 197–198
Topping-up AdBlue®

186
Total distance recorder

20–21
Touch screen

21, 24, 26, 65
Towball, quickly detachable

174–176
Towbar

91, 173
Towbar with quickly detachable
towball

174–176
Towed loads

219–220, 222, 225
Towing another vehicle

215–218
Traction control (ASR)

90–92
Traffic information (TA)

230
Traffic information (TMC)

262
Trailer

91, 173
Trailer stability assist (TSA)

91
Trajectory control systems

90
Triangle, warning

190
Trip computer

22–23
Trip distance recorder

21
Tyres

184, 227Tyre under-inflation detection 129, 196
U
Under-inflation (detection) 129
Unlocking
28, 30
Unlocking from the inside

32
Unlocking the boot

29–30
Unlocking the doors

32
Unlocking the tailgate

29–30
Updating the date

251, 275
Updating the time

251, 275
USB

232, 245–246, 265, 270
V
Ventilation 58
Video
270
Visibility

64
Vision, 180° forward

159
Visiopark 1

158
Visiopark 1 - Visiopark 2

157, 159
Voice commands

257–260
W
Wallbox 169
Warning and indicator lamps
11
Warning lamp, driver''s seat belt
not fastened

96
Warning lamps 11, 20
Warning lamp, seat belts
96
Warnings and indicators

11
Washing

131
Washing (advice)

168, 187–188
Weights

219–220, 222
Welcome lighting

29, 81
Wheel, spare

184, 191–193, 196–198
Windscreen, heated

64–65
Windscreen wipers

83, 85
Wiper blades (changing)

84–85
Wiper, rear

84
Wipers

83, 86
Wipers, automatic rain sensitive

85–86