tow Peugeot 508 2012 User Guide

3
95
i
Comfort
) Switch off the demist/defrost of therear screen and door mirrors assoon as it is no longer needed as lower current consumption results in reduced fuel consumption.


Front Demist -
Defrost






Rear screen
demist - defrost
The control button is located on theair conditioning system control panel.

With manual air
conditioning
)
Select this programme to demistor defrost the windscreen and side windows as quickly aspossible.
With dual-zone and quad-
zone di
gital air conditioning
Automatic visibility programme

Switching on
)
Press this button to demist/defrost the rear screen and, depending on version, the door mirrors. The indicator lamp associated with
the button comes on.

With Stop & Star t, when demisting hasbeen activated, the STOP mode is not
available.


Switching off

The demist/defrost switches off automatically toprevent an excessive consumption of current.)
It is possible to stop the demist/defrost
operation before it is switched off
automatically by pressing the button again.
The indicator lamp associated with the
button
goes off.

The system automatically manages the air conditioning, air flow and air intake, andprovides optimum distribution towards the
windscreen and side windows.
Adjust the temperature control to quickly demist/defrost the windows.
To switch it off, press the "visibility" button
again, the warning lamp in the button goes off
and the system rever ts to the previous settings.

)
Select this programme to demistor defrost the windscreen andside windows as quickly aspossible.
The system automatically manages the air conditioning, air flow and air intake, and provides optimum distribution towards the windscreen and side windows.With the quad-zone digital air conditioning, pressing this button deactivates and locks the
rear air conditioning. ) To stop the programme, press either the "visibility"
button again or "AUTO", the
warning lamp on the button goes off and
the warning lamp in the "AUTO"buttoncomes on.
The system rever ts to the previous settings.The rear screen demist - de
frost can only operate when the engine is running.

4
97
i
!
i
i
Driving











Starting-switching off the engine
With a manual gearbox
, put the gear lever in neutral.
With an electronic gear control gearbox, put the gear lever in N.
With an automatic gearbox
, put the gear lever in P
or N
.
)Inser t the key in the ignition switch. )Turn the key fully towards the dashboard toposition 3 (Starting).)When the engine star ts, release the key.


Starting using the key


Switching off using the key
)Immobilise the vehicle. )Turn the key fully towards you to position 1(Stop)
. )Remove the key from the ignition switch.

For Diesel vehicles, in very cold weather the engine will not star t until the pre-heater warning lamp has
gone off.


Key left in the ignition

If the key is left in the ignition switch,there is an audible signal on opening the driver's door.

If one of the star ting conditions is not met, a reminder message appears inthe instrument panel screen. In somecircumstances, it is necessary to turn the steering wheel slightly while pressing the "STA R T/STOP" button to assist unlocking of the steering; a message warns you when this is needed.


If the vehicle is not immobilised, theengine will not stop.)
With the electronic key inside the vehicle,
press the brake pedal on vehicles withautomatic or electronic gear controlgearbox, or depress the clutch pedal fully
on vehicles with a manual gearbox and
maintain pressure until the engine starts.
Starting using
the electronic key
)Press the " STA R T/STOP"button.


Switching off using
the electronic key
)
Immobilise the vehicle.
)
With the electronic key inside the
vehicle, press the"START/STOP" button.
The en
gine stops and the steering column islocked.

Accessory position
With the electronic key inside the vehicle, press the "STA R T/STOP"button, with no action on the pedals, to switch the ignition on or off and so activate accessories.

4
99
!
!
Driving
It is recommended that you do not apply the parking brake in very cold conditions (ice) and during towing
(breakdown, caravan...). Deactivate theautomatic functions and release theparking brake manually.



Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and the control lever Aare on, not flashing.

The electric parking brake combines
2 operating modes:

-
Automatic Application/Release Application is automatic when the engine stops, release is automatic on use of
the accelerator (this mode is activated bydefault), -Manual Application/Release Manual application of the parking brake is done by pulling control lever A. manual release is done by pushing and releasing the control lever, while pressing
the brake pedal
When the driver's door is opened, there is an
audible si
gnal and a message is displayed if the
brake is not applied.

Programming the mode
Depending on the country of sale of the vehicle,
the automatic application when the engine is switched off and the automatic release whenyou press the accelerator can be deactivated. With the vehicle stationary, to apply the parking
brake whether the en
gine is running or off, pull
control lever A
.


Manual application
Activation/deactivation is done via
the menu in the instrument panel
screen.
The parkin
g brake is then applied and released
manually. The application o
f the parking brake isconfirmed by:


- li
ghting of the braking warning lamp and of the Pwarning lamp
in the control lever A,

- displa
y of the message "Parking brake on".
When the driver’s door is opened with the
engine running, there is an audible signal and a
message is displayed if the parking brake has
not been applied, unless the selector lever is
in position P(Park) in the case of an automatic gearbox.








Electric parking brake
If this warning lamp comes on in the instrument panel, the automatic modeis deactivated.

100
!
i
Driving
With the ignition on or the engine running,
to release the parking brake, pressthe brakepedal
, pullthen release controllever A.
The full release of the parking brake is confirmed by:
Manual release
- extinction of the braking warninglamp and of the P
warning lampin the control lever A ,
- displa
y of the message "Parking brake off".
I
f you pull the control lever Awithout pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel. If necessar
y, you can make a maximum
applicationof the parking brake. It is obtained by means of a long pullon control lever A,
until you see the message "Parking brake
applied fully" and an audible signal is heard.Maximum application is essential:

- in the case of a vehicle towing a caravanor a trailer, if the automatic functions are
activated but you are applying the parkingbrake manually,

- when the slope you are parked on mayvary (e.g. on a ferry, on a lorry, during
towing).
Maximum application


Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and in the control lever Aare on fixed (not flashing).

Never leave a child alone inside thevehicle with the ignition on, as they could release the parking brake.



Automatic application,
engine off



- illumination of the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of the message "Parkingbrake on".
With the vehicle stationary, the parking brake is automatically applied when the engine is
switched off. The application of the parking brake is confirmed by:
In the case of towing, a loaded vehicleor parking on a gradient, make amaximum application of the parkingbrake then turn the front wheels towards the pavement and engage a gear whenyou park.
After a maximum application, the release time will be longer.

112
i!
Driving
Manual operation
)Select position M for sequentialchanging
o
f the six gears.)Pull the lever towards the + sign to changeup a gear. )Push the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
Ddisappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation

This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).

Stopping the vehicle

Before switching off the engine, you can engage position P
or Nto place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle, unless it is pro
grammed
to automatic mode.

Operating fault
When the ignition is on, amessage appears in the
instrument panel screen to indicate a gearbox
fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Have it checked by a PEUGEOT dealer or a qualified workshop.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

You risk damaging the gearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the lever from position Pto another position when the batteryis flat.If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, there is an audible signal and a message appears. )Return the lever to position P;the audible signal stops and themessage disappears.



To r e d u c e fuel consumption when stationary for long periods with the
engine running (traffic jam...), positionthe gear lever at Nand apply theparking brake, unless it is programmed in automatic mode.

4
115
i
!
Driving

Manual gear changing
)
When the vehicle has moved off, select
pos
ition M to change to manual mode. )
Pull the lever towards the +sign to change up a gear. )
Push the lever towards the -sign to change down a gear.



At very low speed, if reverse gear is requested, this will only be takeninto account when the vehicle isimmobilised. A warning lamp appears in the instrument panel screen.

On sharp acceleration, the gearbox willnot change up unless the driver acts onthe gear lever or the steering mountedpaddles. Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised with the brake pedal pressed.
A
disappears and M
appears with thegears engaged successively, in the instrument panel screen.
The
gear change commands are only carried
out if the engine speed permits.It is not necessary to release the accelerator during gear changes. When braking or slowing down, the gearbox
changes down automatically to permitacceleration in the correct gear. This selective
gear change mode enables you
to over take, for example, while still remaining in automatic mode.)Operate the + or -
steering mounted controlpaddle.
The gearbox engages the gear requested if the engine speed permits. A
is still displayed in theinstrument panel.
After a few moments without any action on
the controls, the gearbox resumes automaticcontrol of the gears.
Manual mode

4
129
i
i
i
Driving
In bad weather or in winter, ensure that the sensors are not covered with mud, ice or snow. When reverse gear isengaged, an audible signal (long beep)indicates that the sensors may be dirty.
When the vehicle is moving at a speed below 6 mph (10 km/h), cer tain soundsources (motorcycle, lorry, pneumatic drill, etc.) may trigger the audible signals of the parking sensor system.
In th
e event of a malfunction
of the system, when reversegear is engaged this warning
lamp is displayed in the instrument panel
and/or a message appears in the screen,
accompanied by an audible signal (short beep).
Contact a PEUGEOT dealer or a qualified
wor
kshop.

Operating fault

In addition to the rear parking sensors, the front
parking sensors are triggered when an obstacle
is detected in front and the speed of the vehicle
is still below 6 mph
(10 km/h).
The front parking sensors are interrupted if
the vehicle stops for more than three seconds
in
forward gear, if no fur ther obstacles are
detected or when the speed of the vehicle exceeds 6 mph (10 km/h).
Front par king sensors
The function will be deactivated automatically if a trailer is being towedor a bicycle carrier is fitted (vehicle fitted with a towbar or bicycle carrier recommended by PEUGEOT).

Deactivation/Activation of the front and rear parking sensors
The function is deactivated by pressing this
button. The indicator lamp in the button
comes on.
Pressing this button again reactivates thefunction. The indicator lamp in the buttongoes off.



The sound emitted by the speaker (frontor rear) indicates whether the obstacle is in front or behind.

142
Visibility





Additional directional lighting
With dipped or main beams, this function makes use of the beam from a front foglamp
to illuminate the inside of a bend, when the
vehicle speed is below 25 mph (approximately40 km/h).
This additional lighting is par ticularly useful in
town, at intersections, on very winding roads,
when parking, ...with additional directional li
ghting
without additional directional lighting

Switching on

This function starts


- when the direction indicator is switched on
(the foglamp on the same side is switched on),
or

- from a cer tain angle of rotation of the steering wheel.


Switching off

The system is deactivated:


- below a cer tain angle of rotation of thesteering wheel,

- when switching off the direction indicator,



Programming

The system is activated or
deactivated in the instrument panel
screen configuration menu.
The system is activated by default.

5
143
Visibility








Wiper controls


Programming
Various automatic wiper control modes are also
available according to the following options:


- automatic rain sensitive windscreen wipers,

- rear wiping on engaging reverse gear.

Manual controls
The wipers are controlled directly by the driver. The vehicle's front and rear wipers are
designed to improve the driver's visibility progressively according to the climaticconditions.

Windscreen wipers

Wiping speed:
Model with manual wiping(intermittent)
Model with AUTO wiping
fast (heavy rain),
normal
(moderate rain),
intermittent
(proportional to the
speed of the vehicle),
park,
sin
gle wipe (press down and release),
automatic
(press down and
release
),
single wipe (pull the stalk
briefly towards you).

144
!
Visibility
Rear wiper
If a significant accumulation of snow or ice is present, or when using a bicyclecarrier on the boot, deactivate theautomatic rear wiper via the instrument panel screen configuration menu. Rear wiper selection rin
g:
park,
intermittent wipe,
wash-wipe
(set duration).

Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating.
Th
e function is activated or
deactivated via the instrument panel
screen confi
guration menu.
This function is activated by default.


Programming
)Pull the windscreen wiper stalk towards you. The windscreen wash then the
windscreen wipers operate for a fixed period.
The headlamp washers only operate when the
dipped beam headlamps are on .

Windscreen and headlamp
wash
Screenwash/headlamp washlevel low
In the case of vehicles fittedwith headlamp washers,
when the fluid reservoir lowlevel is reached this warning lamp comes on in
the instrument panel, accompanied by an audible signal and a message in the instrument panel screen.
The warning lamp comes on when the ignition isswitched on, or every time the stalk is operated, until
the reservoir is refilled.
Next time you stop, refill the screenwash/headlamp
wash reservoir.