engine PEUGEOT 607 2004 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2004, Model line: 607, Model: PEUGEOT 607 2004Pages: 173, PDF Size: 1.99 MB
Page 89 of 173
02-02-2004
Flashing of the points in the temperature settingvalues indicates thatthere is a malfunction of
the air conditioning. Contact your
PEUGEOT dealer
9 - Switching off the system
Press the 'OFF'
button.
This action switches
off the display and the
indicator lights and disarms all thesystem functions, with the exceptionof demisting of the rear screen.
Press this button, button 5or one
of the two 'AUTO' buttons again to
reactivate the system with the val- ues which were present before it
was switched off.
10 - Air flow Press buttons '+'
and '-'respectively
to increase ordecrease the air
flow.
As the air flow is adjusted, the innersections of the air flow symbol (fan)are filled in accordingly on the dis-
play. 11 - Air intake/
Recirculation
Press this button torecirculate the inte-
rior air.
Recirculation insulatesthe passenger com-
partment from outside smells andsmoke.
Avoid prolonged operation of inte- rior air recirculation (risk of con-densation and deterioration of airquality).
Press this button again to returnair intake to automatic control. 12 - Demisting the
rear screen
Press this button,with the enginerunning, to demistthe rear screen andthe mirrors.
Demisting stops automatically afterfifteen minutes. Press again to resume demisting.
If the engine is switched off beforethe end of the fifteen minutes,demisting will resume when theengine is switched on again.
Note: it is possible to stop demisting
before it goes off automatically, bypressing the button again. Note: the condensation created by
the air conditioning system causes a flow of water under the vehicle when
stationary, which is perfectly normal.
YOUR 607 IN DETAIL
92
Page 91 of 173
02-02-2004
YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
Place the ignition key in the 'run- ning' position (2nd notch),
Adjust your seat and mirrors,
Press button M,then button 1
(first driving position) or button 2
(second driving position) withinfour seconds.
An audible signal confirms that aposition has been memorised. Memorising a new position cancels the previous one. Recalling a memorised position Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting isindicated by a bleep.
Note: after recalling a memorised
position five times in succession, thefunction will be cancelled until theengine is started. Engine running
Keep button 1 or 2pressed down
until the bleep indicates the end of setting of the corresponding mem-orised position.
Memorising seat and mirror positions Four driving positions can be memo- rised:
Ð two, using two remote control
keys (two users) ,
Ð two, using buttons M/1 and M/2.
Driving positions memorised bythe remote control key When locking the doors, the remote control key memorises the positionof the driver's seat and the exteriormirrors. When unlocking the doors, the dri- ver's seat and the exterior mirrorsresume the position memorised bythe remote control key if this haschanged in the meantime. Each remote control key can memorise a specific setting. Front and rear heated seats controls
Press the switch. The tempera-
ture is regulated automatically.
Press it again to stop operation.
Note: the command to activate heat-
ing of the seat(s) remains in thememory for two minutes after the
ignition is switched off.
Page 93 of 173
02-02-2004
YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
Place the ignition key in the 'run- ning' position (2nd notch),
Adjust your seat and mirrors,
Press button M,then button 1
(first driving position) or button 2
(second driving position) withinfour seconds.
An audible signal confirms that aposition has been memorised. Memorising a new position cancels the previous one. Recalling a memorised position Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting isindicated by a bleep.
Note: after recalling a memorised
position five times in succession, thefunction will be cancelled until theengine is started. Engine running
Keep button 1 or 2pressed down
until the bleep indicates the end of setting of the corresponding mem-orised position.
Memorising seat and mirror positions Four driving positions can be memo- rised:
Ð two, using two remote control
keys (two users) ,
Ð two, using buttons M/1 and M/2.
Driving positions memorised bythe remote control key When locking the doors, the remote control key memorises the positionof the driver's seat and the exteriormirrors. When unlocking the doors, the dri- ver's seat and the exterior mirrorsresume the position memorised bythe remote control key if this haschanged in the meantime. Each remote control key can memorise a specific setting. Front and rear heated seats controls
Press the switch. The tempera-
ture is regulated automatically.
Press it again to stop operation.
Note: the command to activate heat-
ing of the seat(s) remains in thememory for two minutes after the
ignition is switched off.
Page 104 of 173
02-02-2004
YOUR 607 IN DETAIL105
Electronic engine immobiliser This locks the engine control system a few moments after the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the codeis recognised and starting is possi-ble. If the system does not function
correctly, the central locking button
indicator light, situated on the centreconsole, flashes rapidly when theignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon as possible. Flat battery (CR 2025/3 volt battery) This is indicated by illumination of a warning light on the instrument panel
display, accompanied by an audiblesignal and a message on the multi-
function display.
Contact a PEUGEOT dealer to
replace the battery.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:
press button A, the courtesy lights
come on and the direction indica-tors flash for a few seconds.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary.Keep your card in a safe place,never inside the vehicle. Programming the remotecontrol Switch off the ignition.
Switch the ignition on again.
Press button Aimmediately for a
few seconds.
Switch off the ignition and removethe remote control key from the
ignition lock. The remote controlis now working again.
Page 105 of 173
02-02-2004
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle, without you being aware of it.
The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except forreprogramming. Do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle:
- ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
YOUR 607 IN DETAIL
106
Page 106 of 173
02-02-2004
YOUR 607 IN DETAIL105
Electronic engine immobiliser This locks the engine control system a few moments after the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the codeis recognised and starting is possi-ble. If the system does not function
correctly, the central locking button
indicator light, situated on the centreconsole, flashes rapidly when theignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon as possible. Flat battery (CR 2025/3 volt battery) This is indicated by illumination of a warning light on the instrument panel
display, accompanied by an audiblesignal and a message on the multi-
function display.
Contact a PEUGEOT dealer to
replace the battery.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:
press button A, the courtesy lights
come on and the direction indica-tors flash for a few seconds.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only if
necessary.Keep your card in a safe place,never inside the vehicle. Programming the remotecontrol Switch off the ignition.
Switch the ignition on again.
Press button Aimmediately for a
few seconds.
Switch off the ignition and removethe remote control key from the
ignition lock. The remote controlis now working again.
Page 107 of 173
02-02-2004
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle, without you being aware of it.
The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except forreprogramming. Do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.
Do not repeatedly press the button of your remote control out of range of your vehicle. You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle:
- ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
YOUR 607 IN DETAIL
106
Page 109 of 173
02-02-2004
DOORS Opening the doors from outside Opening the doors from inside
YOUR 607 IN DETAIL
108
Locking / unlocking from the inside
Ð Using button
Aof the centre con-
sole : This allows the doors, the boot and the fuel filler flap to be locked orunlocked.
Ð Using button B on the door :
¥ on the front doors this allows the doors, the boot and the fuel fillerflap to be locked or unlocked.
¥ on the rear doors this allows the door concerned to be locked orunlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), withthe engine running or when the vehicle is moving, if a door is not properly closed then the dooropen warning light comes on,accompanied by an audible signaland a diagram indicating the relevant
door on the multi-function display. Child safety This prevents either of the rear doors being opened from inside.
Turn the switch a quarter of a turn
using the ignition key.
Page 110 of 173
02-02-2004
YOUR 607 IN DETAIL109
Closing the boot lid Press the push button
Cto start
electric closing of the boot lid.Note: do not hinder closing of the
boot lid: any obstacle to closing causes the boot lid to stop and rise a
few centimetres automatically.
When opening or closing the boot,ensure that no-one is close to therear of the vehicle to avoid the risk
of injury.
To close the boot lid manually, useone of the two handles inside theboot lid.
'Boot open' warning With the ignition on (2nd notch), with the engine running or when thevehicle is moving, the door openwarning light comes on, accompa-nied by an audible signal and a dia-
gram on the multi-function display, ifthe boot is not properly closed. Stopping opening or closing of the boot lid While electric opening or closing of the boot lid is in progress, you canstop its movement at any time.
press the push-button Bor Con
the boot lid.
or
press button Aon the remote
control.
When it is stopped, the boot lid isheld in an intermediate position electrically for approximately 10 minutes. After this time, the system switches to standby and releases the boot lid. Note: to leave the intermediate
position, start an electric opening or closing operation or move the boot
lid manually.
THE MOTORISED BOOT Opening the boot
With the vehicle locked / deadlockedPress and hold
button Aof the
remote control key.
This action will also unlock the doors and the fuel filler flap.
Vehicle unlocked
Press and hold button Aof the
remote control key, or press and
hold push-button Bon the boot
lid.
Note: when the vehicle reaches a
speed of 6 mph (10 km/h), the boot locks and the push button Bis
disarmed. It is reactivated when
stationary, by opening a door.
Page 111 of 173
02-02-2004
YOUR 607 IN DETAIL
110
BONNET Opening Pull the lever, located in the driver's footwell, downwards.
Lift the catch and raise the bonnet.
Bonnet assister struts open the bon-net and keep it open. Closing
Lower the bonnet and release it at the end of its travel.
Check that it is locked.
'Bonnet open' warning With the ignition on (2nd notch), with the engine running or when thevehicle is moving, the door openwarning light comes on, accompa-nied by an audible signal and a dia-
gram on the multi-function display, ifthe bonnet is not properly closed.
¥ safety auto-reverse (on sliding only) When the sunroof is closing and meets an obstacle, it stops thenpartially opens again.
In the event of unwanted opening ofthe sunroof on closing, press part B
of the switch until the sunroof is fully
open. As soon as the sunroof stops,press part Aof the switch until the
sunroof is fully closed. The safety auto-reverse function is not operational during this ope-ration. Note: the sunroof shutter is manual.
Always remove the key from the ignition when leaving the vehicle, even fora short time.
In the event of contact when opera-ting the sunroof, you must reverse
the movement of the sunroof. To dothis, press the switch concerned. When the driver operates the sun- roof switch, he must ensure that noone is preventing correct closing ofthe sunroof. The driver must ensure that passengers use the electric sunroof
correctly. Be aware of children when operating the sunroof.
SUNROOF Control the sunroof:- manually: lightly press the switch;
the roof stops as soon as the switch is released.
- automatically: press the switch
down fully; the roof opens or closescompletely depending on where theswitch is pressed.
¥ to partially open the roof: press
part Aof the switch. To close it,
press part B of the switch.
¥ to open the roof completely:press part Bof the switch.
¥ to close it completely: press part
A of the switch.