change wheel Peugeot 607 Dag 2002 Owner's Manual

YOUR AT A GLANCE9
REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle (per
son, vehicle, tree, gate, kerb...)
located behind the vehicle.
To activate
With the engine running, the sys
tem is activated as soon as
reverse gear is engaged; a bleep
sounds to inform you that it is
active.
The proximity information is
given by an audible signal, con
sisting of bleeps which become
more and more rapid as the vehi
cle approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the
signal becomes con
tinuous.The system ceas
es to be active
when you change
to neutral. TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warn
ing if there is a malfunction (speed
greater than 15 mph (25 km/h).
Tyre underinflation
When this warning light
comes on, accompanied
by a bleep and the mes
sage 'Tyre(s) pressure
low', have the tyre pressure
checked as soon as possible.
Puncture
Display of this warning
light, accompanied by an
audible signal and the
message 'Punctured
tyre(s) detected', is followed by
illumination of the STOPwarning
light.
Stop immediately, avoiding all
abrupt manoeuvres with the
steering wheel and the brakes.
Change the damaged (punctured
or very underinflated) wheel and
have the tyre pressure checked
as soon as possible.
Note: if the damaged wheel is
stored temporarily in the boot, it
will again send this message as a
reminder of the necessity of hav
ing it repaired. This will prevent a
similar warning being displayed. Sensor(s) not detected
Display of this warning
light, accompanied by an
audible signal and the
message 'X tyre pres
sure sensor(s) missing', indi
cates that one or more wheels
are not being detected.
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Warning: this message is dis
played when one of the wheels is
at a distance from the vehicle
(being repaired) or when a wheel
without a sensor is fitted (winter
fitting).
This system does not eliminate
the need to check the tyre
pressure regularly.
128139

INSTRUMENTS AND CONTROLS31
Coolant temperature warning light
This symbol is accompanied by an audible signal and the message
'Engine temperature too high'
on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving
The instrument panel display temporarily shows:
– lights indicating warnings, when these occur,
– vehicle function status indicator lights, when a change occu rs.
Certain warning lights may be accompanied by an audib le signal and a
message on the multifunction display.
List of warning symbols MANUAL CHECK
(vehicle autotest)
 Press the "CHECK"button on
the instrument panel.
With the ignition key in the acces
sories position, with the ignition
switched on, with the engine running
or when the vehicle is moving, this
function informs you at all times of
the following: – any current warnings,
– the status of functions which it is possible to switch on or off (wind
screen wipers, automatic switch
ing on of lights, cruise control, dis
arming of passenger air bag, etc.).
The corresponding warning lights
are displayed in succession on the
instrument panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator lights will be
displayed at the end of this mode.
CHECK mode entry indi
cator light (vehicle
autotest)
This comes on when you
press the 'CHECK' button.
CHECK mode exit indica
tor light (vehicle autotest)
This comes on at the end of
the CHECK mode.
Engine oil pressure warning light
This symbol is accompanied by an audible signal and the message
'Insufficient engine oil pressure' or 'Engine oil pressure too low' on
the multifunction display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light
This symbol comes on accompanied by an audible signal and the me s
sage 'Punctured tyre(s) detected' on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

Selecting telephone mode / Entering a number / Switching off the microphone
To change to telephone mode, press the 'TEL' button or for more than 2 seconds on the steering column
remote control.
Insert your SIM card fully into the slot at the front (use only t he new generation 3V SIM card with bank card
format).
Note: the SIM card must not be taken out while the audio/telepho ne system is still in use. If you forget to do this, an audi
ble signal will sound for a few seconds after the ignition is switched off.
Enter your PIN number and confirm with the 'OK' button in order to access the network. The welcome screen is
displayed.
Note: the PIN code is erased each time the ignition is switched off , but the ''PIN code protection'' function may be
cancelled.
Enter the number of the person you wish to speak to on the di gital keypad and pres the 'OK'button to make the call.
To switch off the microphone midcommunication, press the 'TEL'button.
Cancelling the PIN code request
To cancel the PIN code request, select 'PIN code protection' in the 'Telephone parameters' menu and confirm; select 'OFF'
and confirm, then input your PIN code and confirm.
Receiving / Ending a call
When a ringing sounds to let you know that a call is waiti ng, you can choose either to accept it by press
ing the 'OK'button or not to accept it by pressing button Por by selecting 'Refuse call' using the steer
ing column remote control, pressing the end to confirm.
If you do not accept it, the call is diverted to your voice mai l (if this service is available and active).
To end the call, press button Por the end of the steering wheel remote control.
Note: Not accepting or ending a call by means of the steering whee l control returns the system to radio mode.
Receiving two incoming calls
During a call, when there is another incoming call, you are i nformed of this by a ring and a message. You may choose:
– to accept the call by pressing button 2 then "OK"; the first caller is put on hold and you are in contact wit h the second.
However, pressing button 2 again allows you to return to th e first caller,
– to finish the call you are on and talk to the second call er by pressing button 1 then "OK",
– not to accept the new call by pressing button "C".
YOUR 607 IN DETAIL 63

YOUR 607 IN DETAIL
66
Storing numbers in the telephone directory (SIM)
In the 'Phonebook' menu, validate the 'New Entry' function with the 'OK'button.
Using the alphanumerical keypad input the name, telephone number and address (the memory number) or keep the one
suggested. Confirm each operation with the 'OK'button.
To access a number in the memory: – look for and select it in the menu 'Find by name'or 'Find by address ' of the 'PHONEBOOK' menu and
press the 'OK'button to make the call,
– or press the end of the steering wheel remote control for more than two seconds, look for and select the
number, then press the end of the remote control to make the call,
– or enter the memory number using the keypad, then press button Ffollowed by the 'OK' button to make the
call.
Note: the first nine numbers in this list are directly accessible. Hold one of the nine buttons of the keypad down, then press
the 'OK' button to call.
Selecting the previous item of a menu Press button Mas many times as necessary to select the required item. Confirm with the 'OK' button.
Selecting the following item of a menu Press button Mas many times as necessary to select the required item. Validate wi th the 'OK' button.
Accessing mini messages
In telephone mode: when the buzzer sounds and the 'envelope' symbol is displayed o n the screen, you can access new
messages by pressing the 'MAN' button.
In radio mode: when the symbol appears, you must change to telephone mode (pre ss the "TEL" button) to be able to
access the new messages.
Note: the old stored messages are accessible. In the 'SMS'menu, confirm the 'Messages received' function with the 'OK'
button, then select the message using button 'M'or 'L' to consult it.

YOUR 607 IN DETAIL
79
Navigation options
From the main menu, 'Navigation options'gives you
access to the following programmes:
– management of the directories. This allows details of a stored address to be renamed or deleted, by selecting
the directory and the details to be modified,
– voice synthesis volume adjustment, Once the function has been selected, adjust the volume
of the voice synthesis using the dial, the audio system
button or the steering wheel stalk, then confirm.
Note: the voice synthesis volume can also be adjusted
during a message using the audio system button or the
steering wheel stalk.
– deletion of all data stored in both directories. Guidance tools
Access to the
'Guidance tools' menu is by pressing the
dial at any time during guidance.
It enables:
– the current guidance criterion to be changed,
– the programmed destination to be displayed or changed,
– the voice synthesis volume to be adjusted (see ''Navi
gation options'' ' paragraph),
– the current guidance to be stopped.

EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system
enables the optimum braking pres
sure to be reached more quickly,
thus reducing the stopping distance.
It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in the
resistance of the pedal and an
increase in braking efficiency.
YOUR 607 IN DETAIL
124
ABS ANTILOCK BRAKING
SYSTEM
The ABS system with Electronic
Brake Force Distribution (EBFD)
increases the stability and manoevra
bility of your vehicle, particularly on
poor or slippery road surfaces.
Note:
when changing wheels (tyres
and rims), make sure that these are
approved.
The antilock braking system comes
into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
an audible signal and the
message 'Braking fault' , it
indicates that there is a mal
function of the electronic brake force
distribution, which can cause a loss
of control of the vehicle when
braking.
Stop immediately.
Contact a Peugeot dealer.
Normal operation of the ABS may
make itself felt by slight vibrations
of the brake pedal.
In emergency braking, press
very firmly without releasing
the pressure.
MANUAL GEARBOX
Reverse
To change to reverse gear, lift the
ring under the gear lever knob and
push the gear lever to the left then to
the front.
Reverse gear can only be
engaged when the vehicle is sta
tionary with the engine idling.

YOUR 607 IN DETAIL
126
ELECTRONICALLY
CONTROLLED SUSPENSION
T
he suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving the
comfort of the occupants and the vehi
cle's road holding capabilities.
The suspension favours smooth shock
absorption, ensuring a comfortable ride,
but as soon as conditions demand a
change (sporty driving, tight bends,
avoidance action, etc.) it automatically
selects firmer shock absorption, guaran
teeing optimum road holding.
Selecting the SPORT position
 Press switch 1, the SPORT indi
cator light will come on,
accompanied by an audible
signal.
In this position, the suspen
sion is maintained in the
SPORT position.
To return to automatic
operation
 Press switch 1again. The indicator
light will go out and the
AUTO indicator light comes
on, accompanied by an audi
ble signal.
Operating check
This is confirmed by the switch light
and the indicator lights. The switch
light comes on for approximately three
seconds every time the ignition is
switched on.
If the switch light flashes or if the indi
cator light comes on, accompanied by
an audible signal and the message
' Hydraulic suspension pressure
insufficient' , contact your PEUGEOT
dealer.
Handbrake
Locking
When parking, pull the handbrake to
immobilise your vehicle.
Warning: when parking on a slope,
direct your wheels towards the pave
ment and pull on the handbrake.
Unlocking
Pull the handle and press the button
to release the handbrake.

139
TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warning
in the event of malfunction (speed
greater than 15mph [25 km/h]).
Flat tyreWhen this warning light
comes on, accompanied by
an audible signal and the
message 'Tyre pressure
low' on the multifunction
display, have the tyre pressure
checked as soon as possible.
Puncture
This warning light, accom
panied by an audible signal
and the message 'Punc
tured tyre(s) detected' on
the multifunction display, is
followed by illumination of the
'STOP' warning light.
Stop immediately, avoiding any sud
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
very deflated) tyre, and have the tyre
presure checked as soon as possible.
Note: if the damaged tyre is tem
porarily stored in the boot, it will
again emit this message to remind
you of the necessity of having it
repaired. This will prevent another
warning of the same type being dis
played. Sensor(s) not detected
This warning light, accom
panied by an audible signal
and the message ' X tyre
pressure sensor(s) miss
ing ' on the multifunction
display, indicates that underinflation
detection is absent from one (or sev
eral) tyre(s).
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Note: this message is also displayed
when one of the tyres is away from
the vehicle (being repaired) or when
a wheel without a sensor is fitted.
LES INFORMATIONS PRATIQUES
All repairs and changing
of tyres on a wheel fitted
with this system must be
carried out by a
PEUGEOT dealer.
The tyre underinflation detec
tion system is an aid to driving
which does not replace the
need for the driver to be vigilant
or to drive responsibly.
This system does not remove the
necessity for having the tyre pres
sure (including that of the spare
wheel) checked regularly, to
ensure optimum dynamic perfor
mance of the vehicle and to pre
vent premature wear of the tyres,
particularly in the case of arduous
driving conditions (heavy load,
high speed).
The system may temporarily be
disturbed by radio broadcasts on
a frequency close to it.

PRACTICAL INFORMATION 141
Fold the jack by pressing at the
ends
Aand place it in one of the
four locations Eunderneath the
vehicle (the nearest one to the
wheel to be changed).
Extend the jack, first by hand, pul
ling the ends Athen using wheel
brace 1and the extension 3.
Remove a wheel bolt at the top
and fit the centralising tool 2in its
place.
Unscrew the other bolts and
remove the wheel.
Fitting a wheel
Position the wheel using the cen
tralising tool to assist you.
Tighten the bolts by hand and
remove the centralising tool.
Partly tighten the bolts using the
wheelbrace.
Fold the jack and remove it.
Fully tighten the bolts using the
wheelbrace.
Replace the wheel trim.
Put the tool holder back in posi
tion. This helps to keep the boot
floor in its correct position, to pre
vent any deformation of the floor
when loaded.
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. For your safety, always
change the wheel:
– on level, stable, nonslippery
ground,
– with the handbrake applied,
– with first or reverse gear engaged (position Pfor the
automatic gearbox),
Never go underneath a vehicle
which is supported only by a
jack (use a ramp).
After changing the wheel:
– have the tightening of the bolts and the tyre pressure checked
by a PEUGEOT dealer as soon
as possible.
– have the punctured wheel repaired and refit it to the vehi
cle as soon as possible.
Tyres fitted with the Tyre Under
Inflation Detection System.
These wheels have a pressure
sensor. Have them repaired by a
PEUGEOT dealer.

PRACTICAL INFORMATION155
ACCESSORIES FOR YOUR 607
For your PEUGEOTonly use accessories and original parts approved by the
manufacturer.
These accessories and parts are all adapted to your PEUGEOT, after being tested and approved for reliability and safe
ty, which PEUGEOTcannot guarantee for other products.
A wide choice of original accessories, approved by PEUGEOT, is availa ble through the dealer network. T hey all carry the
PEUGEOTguarantee:
– Security : Antitheft alarms (prewired function), window engraving, wheel antitheft devices, first aid kit
etc.
– Protection : Covers compatible with side air bags, mats, boot tray, styling mu d flaps.
– Communication : Telephone, navigation equipment with monochrome (prewired fu nction) or colour screen , CD
changer, speakers.
– Customising : Alloy wheels, wheel trims, spoiler.
– Comfort : Portable refrigerator, telephone console.
– Leisure pursuits : Trailer tow bar (maximum towable load: 1800 kg), roof bars (maximum l oad: 75 kg), transpor
tation accessories (bicycle carrier, ski carrier), roof box, snow chains etc.
– Children : Booster seats and child seats, rear blind.
– Maintenance products:Windscreen wash fluid, interior and exterior cleaning and main tenance products.
Before fitting any electrical accessory to your vehicle, consult a PEUG EOT dealer.