check engine light Peugeot 607 Dag 2002 Owner's Manual

YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off but
the accessories still function.
2nd notch, Running position:
The ignition is on.
Starting position:
Operates the starter.
Starting a diesel engineIf the temperature is highenough, the preheat
indicator light does not
come on and you can
start immediately.
If the indicator light comes on,
wait for it to go out before operat
ing the starter.
If the engine stalls, it is neces
sary to return the key to the
'Stop' position before restarting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been
detected: In the absence of
vehicle function status indi
cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.
Otherwise, it will be displayed after
these indicator lights come on.
If a 'minor' malfunction has been
detected: the warning light for the
faulty function is displayed on the
instrument panel screen. Certain
indicator lights showing the status of
vehicle functions may also come on,
followed by the OKindicator light.
If a 'major' malfunction has been
detected: the corresponding warn
ing light is displayed on the instru
ment panel screen. Certain indicator
lights showing the status of vehicle
functions may also come on. The
OK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air
bag is disarmed, the correspond
ing warning light will come on.
With the engine running or if the
vehicle is moving, the instrument
panel screen temporarily displays:
– lights indicating warnings, when
these occur,
– vehicle function sta tus indicator lights,
when a change
occurs.
The display of certain indicator
lights is accompanied by an audi
ble signal and a message on the
multifunction display.
MANUAL CHECK  Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories
position, with the ignition switched on,
with the engine running or the vehicle
moving, this function informs you at all
times of the following:
– any current warnings,
– the status of functions which it is possible to switch on or switch off
(windscreen wipers, automatic
switching on of lights, cruise con
trol, disarming of passenger air
bag, etc.).
The corresponding warning lights are
displayed in succession on the instru
ment panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator light(s) will be
displayed at the end of this mode.
Never run the engine in
a confined space.
Do not make any modi fications to the steering
lock.
31

CRUISE CONTROL
Cruise control enables the vehi
cle to maintain a steady speed
programmed by the driver, with
out the accelerator being
pressed.
In order for it to be memorised,
the speed of the vehicle must be
greater than 25mph (40km/h) or
40mph (60km/h) depending on
engine.
OperationPlace the ring of stalk
A in the ONposition. The
indicator light comes on,
accompanied by an audi
ble signal. FRONT AIR BAGS
Disarming the passenger air
bag*
with the ignition off, insert the
key into slot
1and turn it:
–to the 'ON'position, the pas
senger air bag is armed,
–to the 'OFF'position, the pas
senger air bag is disarmed.
Operating check When the passenger air
bag is disarmed, the
warning light comes on
when the ignition is
switched on (2nd notch),
accompanied by an audible sig
nal and the message 'Passenger
air bag disarmed' . Front air bag faulty
If this warning light
comes on, accompanied
by an audible signal and
the message 'Air bag
faulty' , contact a PEUGEOT
dealer to have the system
checked.
Passenger air bag
precautions
 Disarm the
air bag if you
install a rear
facing child
seat.  Arm the air
bag for an
adult passen
ger.
Never place your feet or any
object on the fascia.
* According to country
YOUR AT A GLANCE11
127129

YOUR AT A GLANCE9
REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle (per
son, vehicle, tree, gate, kerb...)
located behind the vehicle.
To activate
With the engine running, the sys
tem is activated as soon as
reverse gear is engaged; a bleep
sounds to inform you that it is
active.
The proximity information is
given by an audible signal, con
sisting of bleeps which become
more and more rapid as the vehi
cle approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the
signal becomes con
tinuous.The system ceas
es to be active
when you change
to neutral. TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warn
ing if there is a malfunction (speed
greater than 15 mph (25 km/h).
Tyre underinflation
When this warning light
comes on, accompanied
by a bleep and the mes
sage 'Tyre(s) pressure
low', have the tyre pressure
checked as soon as possible.
Puncture
Display of this warning
light, accompanied by an
audible signal and the
message 'Punctured
tyre(s) detected', is followed by
illumination of the STOPwarning
light.
Stop immediately, avoiding all
abrupt manoeuvres with the
steering wheel and the brakes.
Change the damaged (punctured
or very underinflated) wheel and
have the tyre pressure checked
as soon as possible.
Note: if the damaged wheel is
stored temporarily in the boot, it
will again send this message as a
reminder of the necessity of hav
ing it repaired. This will prevent a
similar warning being displayed. Sensor(s) not detected
Display of this warning
light, accompanied by an
audible signal and the
message 'X tyre pres
sure sensor(s) missing', indi
cates that one or more wheels
are not being detected.
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Warning: this message is dis
played when one of the wheels is
at a distance from the vehicle
(being repaired) or when a wheel
without a sensor is fitted (winter
fitting).
This system does not eliminate
the need to check the tyre
pressure regularly.
128139

PEUGEOT SERVICING 25
Level
Operations Description of operation 1st service
A C Intermediate
DRAIN/REFILL Engine oil Bleed fuel filter (diesel) Oil filter Fuel filter
*(petrol)REPLACE Fuel filter element (diesel) Air filter element Spark plugs (petrol) Engine oil (check + topup) Manual gearbox oil (check + topup) Battery (check + topup) if cap is removableLEVEL Screen wash (check + topup) Coolant (check + topup) Brake fluid (check + topup) Power steering fluid (check + top up according to specification ) Operation of lights and indicators Condition of glass, headlamp and light lenses and mirrors Horn Windscreen washer jets Condition of wiper blades Condition and tension of the ancillary drive belts Handbrake Condition of hydraulic circuits (hoses and covers)CHECK Condition of rubber boots and gaiters Brake pads o Play in hubs, link rods, ball joints, flexible mountings Shock absorbers Rear drum brake lining wear Condition and pressure of tyres (including spare wheel) Emission control check as per current legislation (petrol) Smoke opacity (diesel) Pollen filter (according to specification)o
Visual check of the whole vehicle


: All driving conditions o: Arduous conditions * According to destination
SERVICE
ROAD TEST
A AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
Courtesy vehicle

INSTRUMENTS AND CONTROLS
28
1 Handbrake indicator light.
2 Main beam headlamps indicator
light.
3 Dipped beam headlamps
indicator light.
4 Rev counter.
5 Lefthand direction indicator.
6 Fuel gauge.
7 Righthand direction indicator.
8 Speedometer. 9
Front fog lamps indicator light.
10 ABS antilock braking system
warning light.
11 Rear fog lamps indicator light.
12 Engine diagnostics warning
light.
13 Coolant temperature indicator.
14 CHECK button.
15 Trip recorder zero reset.
16 Service indicator and total
distance recorder. 17
Warning/status screen.
18 Illumination button +.
19 Illumination button .
20 Engine oil level indicator.
Engine oil temperature
indicator.
INSTRUMENT PANEL DIALS: PETROL

INSTRUMENTS AND CONTROLS29
1
Handbrake indicator light.
2 Main beam headlamps
indicator light.
3 Dipped beam headlamps
indicator light.
4 Rev counter.
5 Lefthand direction indicator.
6 Fuel gauge.
7 Righthand direction indicator.
8 Speedometer. 9 Front fog lamps indicator light.
10
ABS antilock braking system
warning light.
11 Rear fog lamps indicator light.
12 Engine diagnostics warning
light.
13 Coolant temperature indicator.
14 CHECK button.
15 Trip recorder zero reset.
16 Service indicator and total
distance recorder. 17
Warning/status screen.
18 Illumination button +.
19 Illumination button .
20 Engine oil level indicator.
20Engine oil temperature
indicator.
INSTRUMENT PANEL DIALS: DIESEL

INSTRUMENTS AND CONTROLS31
Coolant temperature warning light
This symbol is accompanied by an audible signal and the message
'Engine temperature too high'
on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving
The instrument panel display temporarily shows:
– lights indicating warnings, when these occur,
– vehicle function status indicator lights, when a change occu rs.
Certain warning lights may be accompanied by an audib le signal and a
message on the multifunction display.
List of warning symbols MANUAL CHECK
(vehicle autotest)
 Press the "CHECK"button on
the instrument panel.
With the ignition key in the acces
sories position, with the ignition
switched on, with the engine running
or when the vehicle is moving, this
function informs you at all times of
the following: – any current warnings,
– the status of functions which it is possible to switch on or off (wind
screen wipers, automatic switch
ing on of lights, cruise control, dis
arming of passenger air bag, etc.).
The corresponding warning lights
are displayed in succession on the
instrument panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator lights will be
displayed at the end of this mode.
CHECK mode entry indi
cator light (vehicle
autotest)
This comes on when you
press the 'CHECK' button.
CHECK mode exit indica
tor light (vehicle autotest)
This comes on at the end of
the CHECK mode.
Engine oil pressure warning light
This symbol is accompanied by an audible signal and the message
'Insufficient engine oil pressure' or 'Engine oil pressure too low' on
the multifunction display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light
This symbol comes on accompanied by an audible signal and the me s
sage 'Punctured tyre(s) detected' on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS33
Tyre underinflation warning light
Display of this warning light is acompanied by an audible si
gnal and the message 'Tyre(s) pressure low' on the
multifunction display.
Have the tyre pressure checked as soon as possible.
Low coolant level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Cooling circuit level low' on
the multifunction display .
Stop immediately.
Warning: wait for the engine to cool before topping up.
The cooling system is pressurised.
In the event of breakdown and to prevent the risk of scalding , unscrew the cap by two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Seat belt not fastened' on the
multifunction display.
With the engine running, the warning light comes on when the driver's seat belt is unfastened.
Electronic immobiliser warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Electronic theft protection
faulty' on the multifunction display.
It indicates a malfunction of the electronic immobiliser system.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
40
Coolant temperature indicator
When the needle is in
zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high.
In cases where the coolant tem
perature warning light comes on
(linked to the STOPwarning light),
you must stop immediately.
Warning: wait for the engine to cool
down.
If necessary, top up the level.
Because the cooling system is pres
surised, to prevent the risk of scald
ing, turn the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.Engine oil level and
temperature
When the ignition is switched on, this
gauge indicates the engine oil level
for approximately 20 seconds, then it
indicates the engine oil temperature.
Engine oil level
The reading is valid only if the vehi
cle is on level ground, and the
engine has been switched off for 10
minutes.
With the ignition on, wait for the
graduated sector to light up and the
indicator needle to move.
When the needle is in zone C, the oil
level is correct.
When the needle is in zone D, the oil
level is incorrect.
There is a risk of damage to the
engine.
 Check the level with the dipstick.
You must top up the level without
exceeding the maximum level on
the gauge.
Engine oil temperature
When the needle is in zone E, the
temperature is correct.
When the needle is in zone F, the
temperature is too high.
Reduce your speed to lower the
temperature.
Service indicator and total
distance recorder
When the ignition is switched on, this
indicates servicing information for a
few seconds, then the total and trip
distances.
Service function
See the 'Service indicator' section.
Total distance recorder function
The total distance is displayed on the
left side of the screen and the trip
distance on the right side.

The engine and the ignition must
be switched off when filling with
fuel : Open the fuel filler flap by press
ing its front right hand edge,
 Unscrew the cap and hook it over
the tab located on the inside of the
flap.
When filling up your tank, do not con
tinue after the 3rd cutoff of the
pump; this could cause your vehicle
to malfunction.
The capacity of the tank is approx
imately 80 litres.  After filling the tank, screw the cap
on fully and close the flap.
Fuel filler cap open When this light comes on,
accompanied by an audible
signal and the message
'Fuel cap open' on the dis
play, screw the cap on again
and close the fuel filler flap.
YOUR 607 IN DETAIL 107
BONNET
Opening
 Pull the lever, located in the dri
ver's footwell, downwards.
 Lift the catch and raise the bon
net.
Bonnet assister struts open the bon
net and keep it open.
Closing
 Lower the bonnet and release it at
the end of its travel.
 Check that it is locked.
'Bonnet open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multi–function display, if the bonnet
is not properly closed. FILLING WITH FUEL
Low fuel level
When the minimum fuel
level is reached, this warn
ing light comes on, accom
panied by an audible signal
and the message 'Fuel
level low' on the multifunction dis
play.
You can can still drive approxi
mately 30 miles (50 km) without
filling up with fuel.
Filling with fuel
Locking and unlocking of the fuel
filler flap, the doors and the boot is
simultaneous (except when selective
unlocking is initialised; in this case
press the unlocking button of the
remote control again).