tyre pressure Peugeot 607 Dag 2002 Owner's Manual

YOUR AT A GLANCE9
REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle (per
son, vehicle, tree, gate, kerb...)
located behind the vehicle.
To activate
With the engine running, the sys
tem is activated as soon as
reverse gear is engaged; a bleep
sounds to inform you that it is
active.
The proximity information is
given by an audible signal, con
sisting of bleeps which become
more and more rapid as the vehi
cle approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the
signal becomes con
tinuous.The system ceas
es to be active
when you change
to neutral. TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warn
ing if there is a malfunction (speed
greater than 15 mph (25 km/h).
Tyre underinflation
When this warning light
comes on, accompanied
by a bleep and the mes
sage 'Tyre(s) pressure
low', have the tyre pressure
checked as soon as possible.
Puncture
Display of this warning
light, accompanied by an
audible signal and the
message 'Punctured
tyre(s) detected', is followed by
illumination of the STOPwarning
light.
Stop immediately, avoiding all
abrupt manoeuvres with the
steering wheel and the brakes.
Change the damaged (punctured
or very underinflated) wheel and
have the tyre pressure checked
as soon as possible.
Note: if the damaged wheel is
stored temporarily in the boot, it
will again send this message as a
reminder of the necessity of hav
ing it repaired. This will prevent a
similar warning being displayed. Sensor(s) not detected
Display of this warning
light, accompanied by an
audible signal and the
message 'X tyre pres
sure sensor(s) missing', indi
cates that one or more wheels
are not being detected.
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Warning: this message is dis
played when one of the wheels is
at a distance from the vehicle
(being repaired) or when a wheel
without a sensor is fitted (winter
fitting).
This system does not eliminate
the need to check the tyre
pressure regularly.
128139

PEUGEOT SERVICING 21
Zero reset
Your Peugeot dealer carries out this
operation after each service. Howev
er, if you carry out the service your
self, the reset procedure is as fol
lows: 
Switch off the ignition,
 Press and hold the trip recorder
reset button,
 Switch on the ignition.
The display begins a countdown.
When the display shows 0, release
the button; the service symbol disap
pears.
Important: after this operation, if
you wish to disconnect the battery,
lock the vehicle and wait for at least
five minutes, otherwise the zero re
set will not be registered.MAINTENANCE OF PARTS SUBJECT TO WEAR AND A CHECK OF CON
SUMABLES
Certain essential components on your vehicle are subject to checks a t specific
frequencies.
•The brake fluid is to be replaced at a maximum of every 36,000/40,000 miles
(60 000km) or every two years;
•The pollen filter must be checked at each serviceby a PEUGEOT dealer
(services and intermediate visits) or more often, depending on the environ
ment (dust, pollution, etc.);
•For HDI turbo diesel engines with particulate emission filter , maintenance
of the filterand topping up of the additive reservoirmust be carried out
every 48,000 miles (80 000 km) by a PEUGEOT dealer;
• Replacement of the timing belt: contact a PEUGEOT dealer.
• Air bags and pretensioning parts on seat belts must be replaced every
10 years.
• Tyre pressure sensors are to be replaced every 10 years.
• The check on tyre inflation presure must be carried out cold at least once a
month.

PEUGEOT SERVICING 25
Level
Operations Description of operation 1st service
A C Intermediate
DRAIN/REFILL Engine oil Bleed fuel filter (diesel) Oil filter Fuel filter
*(petrol)REPLACE Fuel filter element (diesel) Air filter element Spark plugs (petrol) Engine oil (check + topup) Manual gearbox oil (check + topup) Battery (check + topup) if cap is removableLEVEL Screen wash (check + topup) Coolant (check + topup) Brake fluid (check + topup) Power steering fluid (check + top up according to specification ) Operation of lights and indicators Condition of glass, headlamp and light lenses and mirrors Horn Windscreen washer jets Condition of wiper blades Condition and tension of the ancillary drive belts Handbrake Condition of hydraulic circuits (hoses and covers)CHECK Condition of rubber boots and gaiters Brake pads o Play in hubs, link rods, ball joints, flexible mountings Shock absorbers Rear drum brake lining wear Condition and pressure of tyres (including spare wheel) Emission control check as per current legislation (petrol) Smoke opacity (diesel) Pollen filter (according to specification)o
Visual check of the whole vehicle


: All driving conditions o: Arduous conditions * According to destination
SERVICE
ROAD TEST
A AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
Courtesy vehicle

INSTRUMENTS AND CONTROLS31
Coolant temperature warning light
This symbol is accompanied by an audible signal and the message
'Engine temperature too high'
on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving
The instrument panel display temporarily shows:
– lights indicating warnings, when these occur,
– vehicle function status indicator lights, when a change occu rs.
Certain warning lights may be accompanied by an audib le signal and a
message on the multifunction display.
List of warning symbols MANUAL CHECK
(vehicle autotest)
 Press the "CHECK"button on
the instrument panel.
With the ignition key in the acces
sories position, with the ignition
switched on, with the engine running
or when the vehicle is moving, this
function informs you at all times of
the following: – any current warnings,
– the status of functions which it is possible to switch on or off (wind
screen wipers, automatic switch
ing on of lights, cruise control, dis
arming of passenger air bag, etc.).
The corresponding warning lights
are displayed in succession on the
instrument panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator lights will be
displayed at the end of this mode.
CHECK mode entry indi
cator light (vehicle
autotest)
This comes on when you
press the 'CHECK' button.
CHECK mode exit indica
tor light (vehicle autotest)
This comes on at the end of
the CHECK mode.
Engine oil pressure warning light
This symbol is accompanied by an audible signal and the message
'Insufficient engine oil pressure' or 'Engine oil pressure too low' on
the multifunction display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light
This symbol comes on accompanied by an audible signal and the me s
sage 'Punctured tyre(s) detected' on the multifunction display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS33
Tyre underinflation warning light
Display of this warning light is acompanied by an audible si
gnal and the message 'Tyre(s) pressure low' on the
multifunction display.
Have the tyre pressure checked as soon as possible.
Low coolant level warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Cooling circuit level low' on
the multifunction display .
Stop immediately.
Warning: wait for the engine to cool before topping up.
The cooling system is pressurised.
In the event of breakdown and to prevent the risk of scalding , unscrew the cap by two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Seat belt not fastened' on the
multifunction display.
With the engine running, the warning light comes on when the driver's seat belt is unfastened.
Electronic immobiliser warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Electronic theft protection
faulty' on the multifunction display.
It indicates a malfunction of the electronic immobiliser system.
Contact a PEUGEOT dealer.

INSTRUMENTS AND CONTROLS
36
Antilock braking system (ABS) warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'ABS faulty' on the multifunc
tion display.
If the warning light remains on, or comes on at over 8 mph (12 km/h), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Automatic headlamp adjustment warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic adjustment of
headlamps faulty' on the multifunction display.
It comes on if there is a malfunction of the system.
Contact a PEUGEOT dealer. Automatic gearbox fault warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic gearbox faulty' on
the multifunction display.
It comes on if there is an abnormality in the automatic gearbo x.
The gearbox will continue to operate in downgrade mode (lo cked in 3rd gear).
Contact a PEUGEOT dealer. Tyre underinflation detector battery flat / remote control ba ttery flat / impact sensor fault / wheel(s) miss
ing warning light
Display of this warning light is accompanied by an audible si gnal and a message on the multifunction display show
ing the cause of the warning:
– 'Tyre pressure sensor battery charge low',
– 'Remote control battery charge low',
– 'Impact sensor faulty',
– 'X tyre pressure sensor(s) missing'.
Contact a PEUGEOT dealer.

EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system
enables the optimum braking pres
sure to be reached more quickly,
thus reducing the stopping distance.
It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in the
resistance of the pedal and an
increase in braking efficiency.
YOUR 607 IN DETAIL
124
ABS ANTILOCK BRAKING
SYSTEM
The ABS system with Electronic
Brake Force Distribution (EBFD)
increases the stability and manoevra
bility of your vehicle, particularly on
poor or slippery road surfaces.
Note:
when changing wheels (tyres
and rims), make sure that these are
approved.
The antilock braking system comes
into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
an audible signal and the
message 'Braking fault' , it
indicates that there is a mal
function of the electronic brake force
distribution, which can cause a loss
of control of the vehicle when
braking.
Stop immediately.
Contact a Peugeot dealer.
Normal operation of the ABS may
make itself felt by slight vibrations
of the brake pedal.
In emergency braking, press
very firmly without releasing
the pressure.
MANUAL GEARBOX
Reverse
To change to reverse gear, lift the
ring under the gear lever knob and
push the gear lever to the left then to
the front.
Reverse gear can only be
engaged when the vehicle is sta
tionary with the engine idling.

139
TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warning
in the event of malfunction (speed
greater than 15mph [25 km/h]).
Flat tyreWhen this warning light
comes on, accompanied by
an audible signal and the
message 'Tyre pressure
low' on the multifunction
display, have the tyre pressure
checked as soon as possible.
Puncture
This warning light, accom
panied by an audible signal
and the message 'Punc
tured tyre(s) detected' on
the multifunction display, is
followed by illumination of the
'STOP' warning light.
Stop immediately, avoiding any sud
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
very deflated) tyre, and have the tyre
presure checked as soon as possible.
Note: if the damaged tyre is tem
porarily stored in the boot, it will
again emit this message to remind
you of the necessity of having it
repaired. This will prevent another
warning of the same type being dis
played. Sensor(s) not detected
This warning light, accom
panied by an audible signal
and the message ' X tyre
pressure sensor(s) miss
ing ' on the multifunction
display, indicates that underinflation
detection is absent from one (or sev
eral) tyre(s).
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Note: this message is also displayed
when one of the tyres is away from
the vehicle (being repaired) or when
a wheel without a sensor is fitted.
LES INFORMATIONS PRATIQUES
All repairs and changing
of tyres on a wheel fitted
with this system must be
carried out by a
PEUGEOT dealer.
The tyre underinflation detec
tion system is an aid to driving
which does not replace the
need for the driver to be vigilant
or to drive responsibly.
This system does not remove the
necessity for having the tyre pres
sure (including that of the spare
wheel) checked regularly, to
ensure optimum dynamic perfor
mance of the vehicle and to pre
vent premature wear of the tyres,
particularly in the case of arduous
driving conditions (heavy load,
high speed).
The system may temporarily be
disturbed by radio broadcasts on
a frequency close to it.

PRACTICAL INFORMATION 141
Fold the jack by pressing at the
ends
Aand place it in one of the
four locations Eunderneath the
vehicle (the nearest one to the
wheel to be changed).
Extend the jack, first by hand, pul
ling the ends Athen using wheel
brace 1and the extension 3.
Remove a wheel bolt at the top
and fit the centralising tool 2in its
place.
Unscrew the other bolts and
remove the wheel.
Fitting a wheel
Position the wheel using the cen
tralising tool to assist you.
Tighten the bolts by hand and
remove the centralising tool.
Partly tighten the bolts using the
wheelbrace.
Fold the jack and remove it.
Fully tighten the bolts using the
wheelbrace.
Replace the wheel trim.
Put the tool holder back in posi
tion. This helps to keep the boot
floor in its correct position, to pre
vent any deformation of the floor
when loaded.
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. For your safety, always
change the wheel:
– on level, stable, nonslippery
ground,
– with the handbrake applied,
– with first or reverse gear engaged (position Pfor the
automatic gearbox),
Never go underneath a vehicle
which is supported only by a
jack (use a ramp).
After changing the wheel:
– have the tightening of the bolts and the tyre pressure checked
by a PEUGEOT dealer as soon
as possible.
– have the punctured wheel repaired and refit it to the vehi
cle as soon as possible.
Tyres fitted with the Tyre Under
Inflation Detection System.
These wheels have a pressure
sensor. Have them repaired by a
PEUGEOT dealer.

PRACTICAL INFORMATION
154
T
OWING A TRAILER,
CARAVAN, BOAT ETC...
Only use original PEUGEOTtow
bars which have been tested and
approved from the design stage of
your vehicle.
The tow bar must be fitted by a
PEUGEOTdealer.
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heaviest
loads are as close as possible to the
axle and the nose weight is close to
the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope
increases the coolant temperature.
As the fan is electronically con
trolled, its cooling capacity is not
dependent on the engine speed.
On the contrary, use a high gear to
lower the engine speed, and reduce
your speed. In all cases, pay attention to the
coolant temperature.
Note:
in certain cases of particularly
arduous use (towing the maximum
load up a steep slope in high tem
peratures), the engine automatically
limits its power. In this case, cutting
off the air conditioning allows the
engine power to be recovered, and
therefore the towing speed to be sig
nificantly increased (approximately
12mph [20 km/h] more).
If the coolant temperature warning
light comes on, stop the vehicle and
switch off the engine as soon as pos
sible.
Tyres: check the tyre pressures of
the towing vehicle and of the trailer,
observing the recommended pres
sure.
Brakes: towing increases the brak
ing distance. Drive at a moderate
speed, change down early and brake
gradually.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. Lighting
Manual adjustment
Adjust your headlamps so as not to
dazzle other road users (see section
on ''Manual adjustment of head
lamps''). Check the electrical sig
nalling of the trailer.
Automatic beam correction
For vehicles with Xenon bulbs, this
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
In cases of malfunction, the driver is
alerted by means of the warning light
on the instrument panel.
In this situation the system adjusts
your headlamps to the low position.