ignition Peugeot 607 Dag 2009 Workshop Manual

8
88
Operating check
The gearbox may be dama-
ged if you: - press the accelerator and brake pedals at the same
time,
- force the lever from position P to
another position when the battery
is fl at.
ELECTRONICALLY
CONTROLLED SUSPENSION
 Press switch 1 , the in-
dicator light and the

SPORT indicator light will
come on.
In this position, the suspension is
maintained in the SPORT position,
the shock absorption and the steering
assistance become fi rmer.
Selecting the SPORT position

 Press switch 1 again. The
indicator light will go out
and the AUTO indicator
light comes on, accompa-
nied by an audible signal.
Return to automatic operation
If the switch light fl ashes or if
the indicator light comes on,
accompanied by an audible
signal and a message, contact
a PEUGEOT dealer.
Operating check
This is confi rmed by the switch light
and the indicator lights. The switch li-
ght comes on for approximately three
seconds every time the ignition is swit-
ched on.
Any operating abnormality is
indicated by lighting of this
warning light, accompanied
by an audible signal and a
message on the multifunc-
tion display.
In this situation the gearbox opera-
tes in downgrade mode (locked in
3rd gear). You may feel a substantial
knock when changing from P to R and
from N to R (this will not cause any da-
mage to the gearbox).
Do not exceed 60 mph (100 km/h) or
keep within local speed limits.
Consult a PEUGEOT dealer.
The suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving
the comfort of the occupants and the
vehicle's road holding capabilities.
The suspension favours a smooth
shock absorption, ensuring a comfor-
table ride, but as soon as conditions
demand a change (sporty driving, ti-
ght bends, avoidance action, etc.), it
automatically selects fi rmer shock ab-
sorption, guaranteeing optimum road
holding.
When the ignition is switched on, the
electronic suspension is always active
in automatic operation mode.

8
88
Operating check
The gearbox may be dama-
ged if you: - press the accelerator and brake pedals at the same
time,
- force the lever from position P to
another position when the battery
is fl at.
ELECTRONICALLY
CONTROLLED SUSPENSION
 Press switch 1 , the in-
dicator light and the

SPORT indicator light will
come on.
In this position, the suspension is
maintained in the SPORT position,
the shock absorption and the steering
assistance become fi rmer.
Selecting the SPORT position

 Press switch 1 again. The
indicator light will go out
and the AUTO indicator
light comes on, accompa-
nied by an audible signal.
Return to automatic operation
If the switch light fl ashes or if
the indicator light comes on,
accompanied by an audible
signal and a message, contact
a PEUGEOT dealer.
Operating check
This is confi rmed by the switch light
and the indicator lights. The switch li-
ght comes on for approximately three
seconds every time the ignition is swit-
ched on.
Any operating abnormality is
indicated by lighting of this
warning light, accompanied
by an audible signal and a
message on the multifunc-
tion display.
In this situation the gearbox opera-
tes in downgrade mode (locked in
3rd gear). You may feel a substantial
knock when changing from P to R and
from N to R (this will not cause any da-
mage to the gearbox).
Do not exceed 60 mph (100 km/h) or
keep within local speed limits.
Consult a PEUGEOT dealer.
The suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving
the comfort of the occupants and the
vehicle's road holding capabilities.
The suspension favours a smooth
shock absorption, ensuring a comfor-
table ride, but as soon as conditions
demand a change (sporty driving, ti-
ght bends, avoidance action, etc.), it
automatically selects fi rmer shock ab-
sorption, guaranteeing optimum road
holding.
When the ignition is switched on, the
electronic suspension is always active
in automatic operation mode.

8
90
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:

 press button 3 ;
A brief press increases by 1 mph (1 km/h).
A maintained press increases in steps
of 5 mph (5 km/h).
Using the accelerator:

 exceed the memorised speed until
the required speed is reached,

 press button 2 or 3 .
To memorise a speed lower than the
previous one:

 press button 2 ;
A brief press decreases by 1 mph
(1 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Reactivating the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)): Cancelling the memorised speed

 When the vehicle is stationary, af-
ter the ignition has been switched
off, the system no longer stores
any speed.
Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
the dashes fl ash for a few seconds:
Do not use the cruise control
on slippery roads or in heavy
traffi c.
Contact a PEUGEOT dealer to have
the system checked. This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).

The operations must be carried out:
- while stationary, with the engine
running,

or
- while the vehicle is moving.
Speed limiter function
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly,
- never fi t one mat on top of another.

8
90
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:

 press button 3 ;
A brief press increases by 1 mph (1 km/h).
A maintained press increases in steps
of 5 mph (5 km/h).
Using the accelerator:

 exceed the memorised speed until
the required speed is reached,

 press button 2 or 3 .
To memorise a speed lower than the
previous one:

 press button 2 ;
A brief press decreases by 1 mph
(1 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Reactivating the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)): Cancelling the memorised speed

 When the vehicle is stationary, af-
ter the ignition has been switched
off, the system no longer stores
any speed.
Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
the dashes fl ash for a few seconds:
Do not use the cruise control
on slippery roads or in heavy
traffi c.
Contact a PEUGEOT dealer to have
the system checked. This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).

The operations must be carried out:
- while stationary, with the engine
running,

or
- while the vehicle is moving.
Speed limiter function
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly,
- never fi t one mat on top of another.

8
91
Memorising a speed
A speed can be memorised without
activation of the limiter.
A brief press on buttons 2 and 3 de-
creases or increases by 1 mph (1 km/h).
A maintained press decreases or in-
creases the memorised speed progres-
sively in steps of 5 mph (5 km/h).
Switching the function off

 Place switch 1 in position 0 or

CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in the
memory. Activation/deactivation of the
limiter
The activation is taken into account,
when the vehicle is moving, when the
vehicle speed is at least 5 mph (5 km/h)
below the stored speed.
Pressing button
4 activates the limiter,
pressing this button again deactivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):
Exceeding the programmed speed
In exceptional situations, this method
can be used to exceed the program-
med speed.
Pressing the accelerator to exceed the
programmed speed will have no effect
unless the pedal is pressed fi rmly to
the end of its travel (passing the point
of resistance ).
The limiter is deactivated temporarily
and displays the speed which fl ashes
(e.g. at 70 mph (110 km/h)): To re-activate the limiter, release the
accelerator to slow down to a speed
below the programmed speed.
Operating check
In the event of a limiter malfunction,
the memorised speed is erased, the
dashes fl ash for a few seconds:
To prevent the mat from beco-
ming caught under the pedals: - ensure that the mat is po- sitioned correctly,
- never fi t one mat on top of another.
Contact a PEUGEOT dealer to have
the system checked.
Selecting the function

 Place switch 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default the display indicates:
Note: sometimes (on a steep
descent), the limiter may not
prevent the vehicle from ex-
ceeding the programmed
speed, this speed fl ashes.
On a steep descent or if you
accelerate sharply, the speed
limiter, which does not act on
the brakes, will not be able to
prevent the vehicle from exceeding
the programmed speed.
The speed limiter cannot, in any cir-
cumstances, replace the need to com-
ply with speed limits or the need for
vigilance and responsibility on the part
of the driver.

9
95
BONNET
Closing

 Lower the bonnet and release it at
the end of its travel.

 Check that it is locked.
RUNNING OUT OF FUEL
(DIESEL)
If you should run out of fuel, it is nec-
essary to re-prime the circuit.
If the engine does not start after
15 seconds, repeat the repriming ope-
ration.
Opening

 Pull the lever, located on the left
beneath the dashboard, down-
wards.

 Lift the catch and raise the bonnet.
Bonnet struts open the bonnet and
keep it open.
2 litre 16V HDI engine
- fi ll the fuel tank with at least fi ve li- tres of diesel,
- unclip the style cover to gain ac- cess to the repriming pump,
- unscrew the degas screw,
- squeeze and release the manual repriming pump until diesel is seen
escaping via the degas screw,
- retighten the degas screw,
- operate the starter until the engine starts.
2.7 litre 24V V6 HDI engine
- fi ll the fuel tank with at least fi ve li-tres of diesel,
- switch on the ignition and wait 15 seconds before operating the
starter.

1010
107

Fuse N° Rating
Functions

F1 15 A Front wash-wipe pump and wash-wipe fl uid level sensor.

F2 30 A Locking and deadlocking earth.

F3 5 A Air bags.

F4 10 A Clutch switch, brake dual-function switch, diagnostic connector
, ESP sensor,
electrochromatic mirror.

F5 30 A Front electric windows and sunroof supply.

F6 30 A Rear electric windows supply.

F7 5 A Glove box switch, courtesy lights, map reading lights, courtesy mirrors.

F8 20 A Multifunction display supply, steering wheel control, alarm si
ren, trailer fusebox supply,
PC Com, electric mirror and front and rear electric window controls.

F9 30 A Front and rear lighters (100 W max.).

F10 15 A Additive reservoir control unit supply.

F11 15 A Automatic gearbox control unit, automatic gearbo x positions selection switch, ignition switch.

F12 15 A Trailer fusebox supply, hands-free kit, seats relay, seat memory un
it, rain and brightness
sensor.

F13 5 A Engine fusebox supply.

F14 15 A Parking assistance control unit supply, instrument panel, air co
nditioning, air bags and
pre-tensioners unit.

F15 30 A Locking and deadlocking supply.

F17 40 A Hi-Fi amplifi er, heated mirrors.

1010
108
Engine compartment fuses

Fuse N° Rating
Functions

F1 20 A Engine management control unit.

F2 15 A Horn.

F3 10 A Rear electric blind.

F4 20 A Headlamp wash.

F5 15 A Fuel pump (except 2 litre HDI 16V), diesel heater (2 litre HD
I 16V), turbocharger and diesel
pre-heat unit (2.7 litre HDI 24V).

F6 10 A Power steering, suspension control unit, automatic gearbox, aut
omatic headlamp
adjustment unit.

F7 10 A ESP control unit.

F8 25 A Starter coil.

F9 10 A Coolant level sensor, passenger compartment heating (HDI), S TOP switch.

F10 30 A Engine management actuators (injectors, ignition coil, solen oid valves, oxygen sensors).
To access the fuses located in the en-
gine compartment, remove the cover
and unclip the fuse box lid.
When you have fi nished, close the lid
carefully to guarantee the sealing of
the fuse box and refi t the cover.

1010
109
The electrical system of your vehicle is designed to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on yo ur vehicle, contact a PEUGEOT dealer.

Fuse N° Rating
Functions

F11 40 A Air conditioning blower relay.

F12 30 A Wipers relay.

F13 40 A Built-in systems interface supply (ignition positive).

F14 30 A Air pump.

F15 10 A Right-hand main beam headlamp.

F16 10 A Left-hand main beam headlamp.

F17 15 A Left-hand dipped headlamp.

F18 15 A Right-hand dipped headlamp.

F19 15 A Oil vapour heater (2 litre HDI 16V), inlet air heating sole
noid valve (2 litre HDI 16V), air fl ow
sensor (2 litre HDI 16V and 2.7 litre V6 HDI 24V), oxygen sensor .

F20 10 A Water in diesel sensor (2 litre HDI 16V) injection pump (2.7 l
itre V6 HDI 24V), turbo
regulation solenoid valve (2 litre HDI 16V).

F21 10 A Fan assembly relay control, additional fan assembly (2.7 litre V6 HDI 24V).
PEUGEOT will not accept responsibility for the cost incurred in re pairing your vehicle or for rectifying the malfunctions resulting
from the installation of accessories not supplied a nd not recommended by PEUGEOT and not installed in accordance with its
instructions, in particular when the combined consu mption of all of the additional equipment connected exceeds 10 milliamperes.

1010
110
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position

 Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades at the top of the windscreen
(maintenance position).
ENERGY ECONOMY MODE
After the engine has stopped, certain
functions (windscreen wiper, elec-
tric windows, sunroof, electric seats,
audio equipment, telephone, dipped
headlamps, video, etc.) can only be
used for a limited combined duration,
to prevent discharging of the battery.
Once this period has elapsed, a
switching to economy mode message
appears on the multifunction display
and the active functions are put on
standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to exit the economy mode and
resume the use of these functions im-
mediately, the engine must be started
and left to run for a few minutes.
If the engine has been running for at
least 10 minutes, all of the functions
are active for 30 minutes.
If the engine has been running for
less than 10 minutes, this duration
before returning to economy mode is
5 minutes. All of these functions are
available when the engine is
running.
If the telephone is being used
when economy mode starts, it will still
be possible to fi nish the call.
LOAD REDUCTION FUNCTION
When driving, certain functions (air con-
ditioning, heated rear screen, heating
system for passenger compartment of
diesel vehicles, etc.) may be switched
off temporarily, depending on the level
of battery charge.
Reactivation of these functions is au-
tomatic, once the battery charge is
suffi cient.

Note: at the risk of discharging the
battery, the functions that have been
switched off may be reactivated manually.
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. A fl at battery prevents the en-
gine from starting.
If the doors or boot are opened
several times or if the alarm is
triggered, this may result in activation
of the energy economy mode.