wheel bolts Peugeot 607 Dag 2009 Owner's Manual

1010
100
Access to the spare wheel and the
jack in the boot

 Detach the luggage net.

 Lift the boot carpet using the lifting
hook. Secure this hook behind the
boot seal.
CHANGING A WHEEL
Tools available
The following tools are located in the
polystyrene holder in the centre of the
spare wheel:

1. Wheelbrace.

2. Centralising tool.

3. Wheelbrace extension.

4. Jack.

5. Removable towing eye.

6. Alloy wheel trim remover.

7. Trim cover tool. Removal

 For vehicles with alloy wheels fi tted
with wheel trims, pull the centre trim
by using tool 6 in one of the holes.

 Loosen the wheel bolts.

 Take the jack 4 from the tool kit .

 Place the jack in one of the four
locations A underneath the vehicle
(the nearest one to the wheel to be
changed).

 Extend the jack using wheelbrace 1
and the extension 3 .

 Remove a wheel bolt at the top
and fi t the centralising tool 2 in its
place.

 Unscrew the other bolts and remove
the wheel.
Park the vehicle so that it does
not obstruct traffi c: the ground
must be level, stable and non-
slippery.
Apply the handbrake, switch off the igni-
tion and engage fi rst or reverse gear (po-
sition P for the automatic gearbox).
It is imperative to ensure that the occu-
pants get out of the vehicle and wait in
a safe location.
Never go underneath a vehicle which is
supported only by a jack; use a ramp.
The jack and all of the tools are specifi c
to your vehicle. Do not use them for other
purposes.

1010
101
Fitting a wheel
 Put the tool holder back in position.
This helps to keep the boot fl oor in its
correct position, to prevent any defor-
mation of the fl oor when loaded.

 Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. After changing the wheel:
- have the tightening of the bolts and
the tyre pressure checked by a
PEUGEOT dealer as soon as pos-
sible,
- have the punctured wheel repaired and refi t it to the vehicle as soon as
possible,
- the steel spare wheel must only be used for a very short time.

 Position the wheel using the cen-
tralising tool 2 to assist you.

 Tighten the bolts by hand and re-
move the centralising tool.

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 4 and remove it.

 Fully tighten the bolts using the
wheelbrace.

 Replace the wheel trim.

 For the alloy trims, position the re-
moval hole opposite the valve. Tyres fi tted with the Tyre
Under-Infl ation Detection System.
These wheels have a pressure sensor.
Have them repaired by a PEUGEOT
dealer.

1010
102
Special features of alloy wheels Fitting the spare wheel Anti-theft bolts
Fitting snow tyres
If you wish to fi t snow chains on your
vehicle, contact a PEUGEOT dealer
to fi nd out which models are recom-
mended for your vehicle.
Bolt covers
Alloy wheel bolts are covered by chrome
trims.
Use the yellow tool 7 to remove the
trims before slackening the bolts.
If your vehicle is fi tted with a steel spare
wheel, when fi tting it, it is
normal to no-
tice when tightening the bolts that the
washers do not come into contact with
the rim. The spare wheel is secured by
the cone-shape of each bolt. If your wheels are fi tted with an anti-theft
bolt (one per wheel), the chrome trim
must be removed using the yellow tool,
before unscrewing the bolt using the
anti-theft socket and the wheel brace.

Note: the anti-theft socket
was given to you on delivery
of your vehicle along with the
duplicate keys and the confi -
dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.