check engine PEUGEOT BOXER 2015 Owner's Guide

140
refilling / topping-up the
AdBlue® additive
Precautions to take
use

only AdBlue® additive that meets the
ISO 22241 standard.
the AdBlue® additive is an urea-based
solution.
this liquid is non-flammable, colourless and


odourless.
to be kept in a cool area.
containers (5 or 10 litres) and bottles


(1.89 litres) of AdBlue
®
Please check the use-by date.
Read the instructions on the label.
ensure that you have a suitable filler pipe,


which may or may not be supplied with the
container. Park the vehicle
-
Before topping-up, ensure that the
vehicle is parked on a flat and level


surface.
open the filler
-
Open the fuel filler flap.
-

t
urn the blue cap a 6th of a turn anti-
clockwise.
-
Remove the blue cap downwards.
top-up
-
Obtain a bottle of AdBlue®. After first
checking the use-by date, read carefully
the instructions on use on the label
before pouring the contents of the bottle
into your vehicle's AdBlue
® tank.
Important: if your vehicle's AdBlue
®
tank is completely empty - which is
confirmed by the alert messages and the
impossibility of starting the engine, you
must add at least 3.8 litres (so two 1.89 litre
bottles).
-
After emptying the bottle, wipe away any
spillage around the tank filler using a


damp cloth.
If any additive is split or splashed,
wash immediately with cold water or
wipe with a damp cloth.
If the additive has crystallised, clean it off
using a sponge and hot water.
AdBlue® additive

142
A. Positive metal point on your vehicle
B.
Slave battery
c.

e
arth on your vehicle
Make connections only to the points


indicated and illustrated above. Failure
to observe this instruction introduces
the risk of short-circuit!Starting from another
battery
B
AttErY
c
harging the battery using a
charger
- Connect the red cable to the metal
point
A then to the positive (+) terminal
of the slave battery

B.
-
Connect one end of the green or black
cable to the negative (-) terminal of the


slave battery B .
-
Connect the other end of the green or
black cable to the earth point
c on your
vehicle.
-
Operate the starter, let the engine run.
-
Wait for the engine to return to idle, then


disconnect the cables. -
go to the battery located in the front left
floor.
-
Disconnect the battery.
-
Follow the instructions for use given by
the battery charger manufacturer

.
-
Reconnect starting with the negative (-)
terminal.
-
Check that the terminals and connectors
are clean. If they are covered with


sulphate (white or greenish deposit),
disconnect them and clean them.
Discharged battery

143
Access to the battery
unscrew the 6 access cover retaining
screws.
Lift off or remove completely the access

cover.
Press lever 1 downwards to spread the
clamp.
Remove the terminal 2 from the negative (-)
post.
the batteries contain harmful

substances such as sulphuric acid and
lead.
they must be discarded in accordance

with the provisions of the law and must not,
in any circumstances, be discarded with
household waste.
take used batteries to a special collection
point.
the charging operation must be carried


out in a ventilated area away from
naked flames or any possible sources of
sparks to eliminate the risk of explosion
and fire.
Do not attempt to charge a frozen battery: it
must first be thawed to eliminate the risks of
explosion. If the battery has frozen, before
charging it have it checked by a specialist
who will check that the internal components
have not been damaged and that the
container is not cracked, which could mean
that there is a risk of a leak of toxic and
corrosive acid.
Proceed with a slow charge charge at low
current for a maximum pf about 24 hours to
avoid damaging the battery. Before disconnecting the battery, you must
wait for 2 minutes after switching off the
ignition.
Never disconnect a terminal when the
engine is running.
Never charge a battery without first
disconnecting the terminals.
Close the windows and doors before
disconnecting the battery.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems to be initialised. If slight difficulties
are experienced after this, please contact a
P
eugeOt dealer or a qualified workshop.
Discharged battery
QuICK HeLP
8

146FusesA (amps) Allocation
12 7.5Right-hand dipped headlamp
13 7.5Left-hand dipped headlamp
31 5
engine compartment control unit relay - Dashboard control unit relay (ig\
nition switch +)
32 7.5Cabin lighting (battery +)
33 7.5Battery check sensor on Stop & Start version (battery +)
34 7.5Minibus interior lighting - Hazard warning lamps
36 10Audio system -

Air conditioning controls - Alarm -
tachograph - Battery cut-off control unit -

Additional heating programmer (battery +)
37 7.5Brake lamp switch -
third brake lamp Instrument panel (ignition +)
38 20Central door locking (battery +)
42 5ABS control unit and sensor -

ASR sensor - DSC sensor - Brake lamp switch
43 20Windscreen wiper motor (ignition switch +)
47 20Driver's electric window motor
48 20Passenger's electric window motor
49 5Parking sensors control unit - Audio system - Steering mounted controls - Centre and side switch panels\
-
Auxiliary switch panel - Battery cut-off control unit (ignition switch +)
50 7.5Airbags and pre-tensioners control unit
51 5
tachograph - Power steering control unit - Air conditioning - Reversing lamps - W

ater in Diesel sensor -
Air flow sensor (ignition switch +)
53 7.5Instrument panel (battery +)
89 -Not used
90 7.5Left-hand main beam
91 7.5Right-hand main beam
92 7.5Left-hand front foglamp
93 7.5Right-hand front foglamp
Failed fuse

148
Fuses in the engine compartment
Remove the nuts and tilt the box to access
the fuses.
refit the cover carefully after checking or

replacing fuses. Fuses
A (amps) Allocation
1 40ABS pump supply
2 50Diesel pre-heat unit
3 30Ignition switch - Starter motor
4 40Fuel heater
5 20/50Cabin ventilation with additional programmable heating
(battery +)
6 40/60Cabin fan maximum speed (battery +)
7 40/50/60 Cabin fan minimum speed (battery +)
8 40Cabin fan assembly (ignition switch +)
9 15Rear 12 V socket (battery +)
10 15Horn
11 -Not used
14 15Front 12 V socket (battery +)
15 15Cigarette lighter (battery +)
16 -Not used
17 -Not used
18 7.5
engine management control unit (battery +)
19 7.5Air conditioning compressor
20 30Screenwash/headlamp wash pump
21 15Fuel pump supply
22 -Not used
23 30ABS electrovalves
24 7.5Auxiliary switch panel - Door mirror controls and folding


(ignition switch +)
30 15Door mirror heating
Failed fuse

161
PuncturE rEPAIr KItrepairing the tyre
- Apply the parking brake.
-

u
nscrew the tyre valve cap, remove the

filling hose B and screw the ring E onto
the valve. -
Start the engine.
-
Insert the connector G into the nearest
power socket on the vehicle.
-
Switch on the compressor by placing the
switch F in position

"I" (on).
-
Inflate the tyre to a pressure of 5 bar.
to obtain a more accurate reading, you are
advised to check the pressure value on the


pressure gauge H , with the compressor off.
-
Check that the switch F on the


compressor is in position "0" (off).this temporary puncture repair kit stowed

in a bag located in one of the front door
pockets.
It consists of:
-
a cartridge A , containing the sealant


fluid, equipped with:
●
a filling hose B ,
●
a sticker c indicating "max. 80 km/h",
which the driver must af

fix in full view
(on the dashboard) after repairing
the
tyre,
-
a quick guide to use of the repair kit,
-
a compressor d equipped with a
pressure gauge and unions,
-
adaptors, for the inflation of various
items.
QuICK HeLP
8
Puncture

262
WEIGHtS And toWEd LoAdS (KG)
For more information, refer to your registration certificate.
In each country, it is imperative that the towed loads authorised by
local legislation are complied with.
to find out your vehicle's towing
capacities and its gross train weight, consult a franchised dealer

.
the maximum authorised speed is reduced when towing (comply


with the legislation in force in your country).
With load transfer, the braked trailer weight can be increased,
on condition that the equivalent of this load is removed from the
vehicle so that the
gtW is not exceeded. W

arning: towing with a
lightly loaded towing vehicle may have an adverse effect on its road
holding.
the gtW and towed load values indicated are valid up to a


maximum altitude of 1000 metres; the towed load mentioned must
be reduced by 10 % for each additional 1000 metres.
High ambient temperatures may result in a reduction in the
performance of the vehicle in order to protect the engine; when the
ambient temperature is higher than 37 °C, limit the towed weight.
the kerb weight is equal to the weight without load +


driver
(75 kg) + fuel tank filled to 90%. Before towing a trailer

, check
that:
-
the nose weight on the
towbar ball does not exceed


the value (S) indicated on
the trailer's weights plate,
-
the maximum trailer weight
is less than the value


indicated on the trailer's
weights plate and the
gross


Vehicle Weight (
gVW)


does not exceed the value
indicated on the vehicle's
weights plate.
-
in the case of a self-
supporting trailer, the
gross


train Weight must not


exceed the value indicated
on the vehicle's weights
plate.
General points
tipper body