display Peugeot Boxer 2016 Owner's Manual

12
boxer_en_Chap01_Vue-ensemble_ed01-2015
Eco-drIVInG
o ptimise the use of your gearbox
With a manual gearbox, move off gently and change up without
waiting. While accelerating changing up early. If your vehicle has
the system, the gear shift indicator invites you to engage the most
suitable gear; follow its instructions as soon as it is displayed in
the instrument panel.
drive smoothly
Maintain a safe distance between vehicles, use engine
braking rather than the brake pedal, and press the accelerator
progressively.
t
hese practices contribute towards a reduction in
fuel consumption and CO
2 emissions and also helps reduce the
background traffic noise.
If your vehicle has cruise control, make use of the system at
speeds above 20 mph (30 km/h) when the traffic is flowing well.
control the use of your electrical equipment
Before moving off, if the passenger compartment is too warm,
ventilate it by opening the windows and air vents before using the
air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air
vents open.
Remember to make use of equipment that can help keep the
temperature in the passenger compartment down (window
blinds...).
Switch off the air conditioning, unless it has automatic digital
regulation, as soon as the desired temperature is attained.
Switch off the demisting and defrosting controls, if not automatic.
Switch off the heated seat as soon as possible.
Switch off the headlamps and front foglamps when the level of
light does not require their use.
e

co-driving is a range of everyday practices that allow the motorist to o\
ptimise their fuel consumption and CO
2 emissions.
Avoid running the engine before moving off, particularly in winter;
your vehicle will warm up much faster while driving.
As a passenger, if you avoid connecting your multimedia devices
(film, music, video game...), you will contribute towards limiting the\

consumption of electrical energy, and so of fuel.
Disconnect your portable devices before leaving the vehicle.
Motoring & the environment

30
boxer_en_Chap02_Pret-a-Partir_ed01-2015
Screendisplays indicates Solution - action
temperature /


Ice the ice warning,
the temperature
flashing
accompanied by
a message in
the screen.weather conditions which could
result in ice on the road.
Be particularly vigilant and do not brake sharply.
"Safety - Driving safely".
Date /
t
imea setting: date,


time. a configuration via the "MOD
e "
menu. "
t
echnology on board
- Vehicle configuration" section.
Headlamp beam
height a headlamp
height setting.a position from 0 to 3
depending on the load carried Adjust using the buttons on the MOD
e control panel.
"
e ase of use and comfort - Steering mounted controls"
section.
Service spanner a service
spanner which
remains on.that a service will soon be due.
Refer to the list of checks in the warranty and
maintenance record, then have the service carried out.
Stop & Start on.
engine going into S
t
OP
mode
after the the vehicle stops. As soon as you want to move off, the warning lamp
goes off and the engine restarts automatically in S
t
ARt
mode.
flashes for a few


seconds, then
goes off. S
t
OP
mode temporarily
unavailable or automatic
operation of S
t
ARt mode.Special cases for S

t
OP
mode and S t
ARt mode.
"Ready to set of

f - Starting and stopping" section.
Instruments and controls

31
boxer_en_Chap02_Pret-a-Partir_ed01-2015
Screendisplays indicates Solution - action
g

ear shift
indicator an up arrow. the possibility of changing up. "Ready to set off -
g earbox and steering wheel" section.
Speed limiter on with "OFF".
that the limiter selected is not
active.
Manual selection.
"
e ase of use and comfort - Steering mounted controls"
section.
on. that the limiter is on.
Instruments and controls
2
rEAdY to SEt oFF

34
boxer_en_Chap02_Pret-a-Partir_ed01-2015
under-inflation alert
The alert is given by the fixed
illumination of this warning lamp,
accompanied by an audible signal,
and depending on equipment, the
display of a message.
In the event of a problem on one of the
tyres, the symbol or the message appears,
according to equipment, to identify it.
-

Reduce speed, avoid sudden steering

movements or harsh brake applications.
-

Stop as soon as it is safe to do so.
-


In the event of a puncture, use the

temporary puncture repair kit or the
spare wheel (according to equipment).
-

In the event of under-inflation:
●


if you have a compressor
, the one
in the temporary puncture repair
kit for example, check the four tyre
pressures when cold,


or
●

if it is not possible to check the

tyre pressures at the time, drive
carefully at reduced speed and go to
the nearest P
euge O t
dealer or a

qualified workshop.t he loss of pressure detected does not
always lead to visible deformation of
the tyre.
Do not rely on just a visual check.
t

he alert is maintained until the tyre or
tyres concerned is reinflated, repaired
or replaced.
operating fault
the flashing and then fixed
illumination of this warning lamp
accompanied by the illumination
of the service warning lamp, and
depending on equipment, the display of a
message indicates a fault with the system.
In this case, monitoring of the tyre pressures
is not assured.
t

his alert is also displayed when one or
more wheels is not fitted with a sensor.
g

o to a P
euge O t
dealer or a qualified

workshop

to have the system checked or,
following the repair of a puncture, to have
the original wheel, equipped with a sensor,
refitted.
Instruments and controls

35
boxer_en_Chap02_Pret-a-Partir_ed01-2015
SErVIc E I nd I c At or
For a few seconds after the ignition is
switched on, the spanner symbolising the
service indicator comes on: the screen
informs you when the next service is due,
in accordance with the servicing schedule
indicated in the warranty and maintenance
record.
t

his information is determined in
relation to the distance travelled since the
previous service.
After a few seconds, the display returns to
its usual functions. A long press returns you to the main menu.
Refer to the "
t
echnology on board -

Vehicle configuration" section.
deterioration of the engine oil
Refer to the list of checks in the
warranty and maintenance record
which was given to you on handover of
the vehicle.
reminder of servicing information
At any time, to access the service indicator,
press briefly on the M od E button.
u

se the up/down arrows to see the
scheduling and engine oil wear information.
Pressing the M
od E button again allows you
to return to the various display menus.
Menu...
c

hoose...
Allows you to...
11
Service Service
(miles/
km before
service)
Display the
distance
remaining
before the
next service.
Oil (miles/
km before
oil change) Display
the miles/
kilometres to
the next oil
change.
resetting to zero
the continuous flashing of the indicator is
stopped by a qualified workshop using a
diagnostic tool.
t
his 2
nd warning lamp, coupled
with the 1st, comes on in the
instrument panel when the oil
has not been changed and the
deterioration of the oil has reached another
threshold.
to avoid the risk of damage, have


the oil changed without waiting for this level.
t

he warning lamp flashing and,
if your vehicle has the function,
a message displayed at every
engine start: the system has
detected deterioration of the engine oil.
Have the oil changed as soon as possible.
For 3.0 litre HDi engines, the engine speed
is restricted to 3 000 rpm, then 1 500 rpm
until the oil change is done. Have the engine
oil changed to avoid any risk of damage.
Instruments and controls
2
rEAdY to SEt oFF

41
boxer_en_Chap02_Pret-a-Partir_ed01-2015
Going into engine StArt mode
- t his indicator lamp goes off
and the engine restarts.
If following an automatic restart in S
t
ARt
mode, the driver takes no action on the


the vehicle during the next
3 minutes, the
system stops the engine definitively.
t

he
engine can then only be restarted using
the
key. Special cases: S
tA rt invoked
automatically
t

he S t
ARt mode is invoked automatically

when:
-

the vehicle's is free wheeling on a slope,
-


the windscreen wiper is on fast wipe,
-


the air conditioning is running,
-


the engine has been stopped for around

3 minutes with Stop & Start,
-

some special conditions (battery charge,

engine temperature, braking assistance,
ambient temperature...) where the
engine is needed to assure control of a
system.
In this case, a message appears
in the instrument panel screen,
accompanied by this indicator
lamp, which flashes for a few
seconds, then goes off.Good practice
With a manual gearbox in StOP mode, if a
gear is engaged without fully depressing the
clutch pedal, restarting may not take place.
An indicator lamp and/or message is
displayed in the instrument panel asking
you to fully depress the clutch pedal to allow
restarting.
t

his operation is perfectly normal.
With the vehicle in gear, automatic engine
restarting is only allowed by fully depressing
the clutch pedal.
With the engine stopped in S
t
OP

mode, if the driver unfasten's
their seat belt and opens a front
door, the engine can only be
restarted using the ignition key.
t

here is
an audible signal, accompanied by flashing
of this indicator lamp and the display of a
message.
Starting and switching off
2
rEAdY to SEt oFF

49
boxer_en_Chap03_ergo-et-confort_ed01-2015
cruISE controL
(3
LI tr E H dI E n GI n E )
"this is the speed at which the driver wishes to
travel".
This aid to driving in free-flowing traffic conditions

enables the vehicle to maintain a constant
speed programmed by the driver, except when a
considerable load is carried on a steep gradient.
In order to be programmed or activated,
the vehicle speed must be greater than
approximately 18 mph (30 km/h), with 2nd gear
or higher engaged.
Function selected.
Function deactivated.
If your vehicle is fitted with cruise control,
this is displayed on the instrument panel by
an indicator located in the rev counter.
3
EASE oF uSE and coMFort
Steering mounted controls

55
boxer_en_Chap03_ergo-et-confort_ed01-2015
SPEEd LIMItEr
"this is the selected speed which the driver
does not wish to exceed".
t

his selection is made with the vehicle
stationary and the engine running or with the
vehicle moving and 2
nd gear or higher engaged.
t

he lowest speed that can be programmed
is 20 mph (30 km/h).
t

he speed of the vehicle responds to the
pressure of the driver's foot as far as the
accelerator pedal point of resistance which
indicates that the programmed speed has been
reached. However, pressing the pedal beyond this
point of resistance to the floor permits
exceeding of the programmed speed.
to


resume use of the limiter, simply reduce
the pressure on the accelerator pedal
gradually and return to a speed below that
programmed.
t

he operating actions may be carried out
with the vehicle stationary and the engine
running, or with the vehicle moving.
t
his speed limiter shows the status of the
system and the programmed speed in the
instrument panel screen:
System selected,
display of the "Speed
Limiter" indicator.
System deactivated,
last programmed speed - o FF
(example at 65 mph
(107 km/h)).
System activated
(example at 65 mph (107 km/h)).
Vehicle speed above
(example 70 mph (118 km/h))
the programmed speed is
displayed flashing.
Operating fault detected,
o

FF - the dashes flash.
3
EASE oF uSE and coMFort
Steering mounted controls

56
boxer_en_Chap03_ergo-et-confort_ed01-2015
Selecting the function
- turn the ring fully downwards. the
speed limiter is selected but is not yet
active.
t

he display indicates o FF and
the last programmed speed.
Programming a speed
A speed can be programmed without
activating the limiter but with the engine
running.
to memorise a speed higher than the


previous one:
-

move the switch up (+).
A

brief press increases the speed by
1
mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
to memorise a speed lower than the


previous one:
-

move the switch down (-).
A

brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h).
Activation/deactivation
Pressing this button once activates the
speed limiter, o FF disappears from the
screen and a message appears to confirm
the activation.
A second press deactivates it,
o FF
reappears in the screen and a message
appears to confirm the deactivation.
Steering mounted controls

63
boxer_en_Chap03_ergo-et-confort_ed01-2015
dIGItAL AIr cond I t I on I n G -
Mono-zon E
If your vehicle is fitted with this system,
the controls are located in the middle of
the
dashboard.
Auto mode
Switching on FuLL Auto mode:
pressing the A uto control switches
on the system's functions, confirmed
by the display of F
u LL A uto . t his
is the normal operating mode for the digital air
conditioning system.
u

sing the moving ring surrounding the A ut
O

control, set the comfort temperature to be reached
according to a setting between:
-
HI (High to ≈

32) and,
-
LO (Low to ≈

16).
The system controls the distribution, flow and
intake of air to ensure comfort equivalent to the
setting displayed and sufficient recirculation of air
in the passenger compartment.
No further adjustments are required.
Control screen for your digital air
conditioning system.
Auto mode with personalisation
Switch on in Auto mode, certain
settings can be modified: the
distribution, the air flow, the air
conditioning and the air intake/
recirculation.
t

he display changes from F u LL A uto to
A
uto
.
to return to fully automatic operation, press


this button again.
t

he display on the control
panel changes from A
uto to F u LL A uto .
If the system is not able to maintain
the setting selected following manual
adjustments, the setting flashes then A
uto

is cleared. Press the

A uto control to return
to the automatic settings.
Switching off the air conditioning
Pressing this control switches
off the air conditioning functions.
t

he snowflake is cleared from the
screen.
complete switch-off
Pressing this control switches
the system off.
t
he L e D and the
screen switch off.
When the engine is running and the air
conditioning is on, this symbol and the
message F
u
LL A
uto
are displayed.
t

he other components are displayed according
to the settings selected by the user.
Ventilation
3
EASE oF uSE and coMFort