lock PEUGEOT EXPERT 2023 Owner's Guide

58
Ease of use and comfort
â–º To return the seat, tip the bench towards the
rear until the feet lock into place..
It is not necessary to fold the backrest
(table position) to tip the bench seat for
access to row 3.
Folding the backrest to the
table position
â–º Put the head restraints in the low position.

â–º From the rear , lower the handle to release the
backrest.
â–º

From the front, raise the handle to release
the backrest.
â–º


Fold the backrest onto the cushion.
â–º


T
o return the backrest to its normal position,
raise the handle and pull the backrest up.
Do not leave objects (such as a bag or
toys) on the cushion when folding the
backrest.
Tilting
â–º If your vehicle has the facility , place the
backrest in the table position.


â–º Using the handle, release the rear feet then
tip the seat forward.
â–º

T
o return the seat, tip the bench towards the
rear until the feet lock into place..
Removing
â–º If the vehicle is so equipped, place the
backrest in the table position.
â–º

T
ip the bench seat.


â–º Release the front feet using the handles.
â–º Disengage the bench seat from its
anchorages.
â–º

Remove the bench seat.
Refitting
â–º Check that there is no object obstructing the
anchorages and preventing the feet locking into
place.


â–º Engage the front feet in the anchorages on
the floor (as shown above).
CarM an uals 2 .c o m

59
Ease of use and comfort
3

â–º Lock the front feet using the handles.
â–º T ip the bench seat backwards until the rear
feet lock into place.
Be careful of passengers' feet when
tipping.


â–º If the vehicle is so equipped, pull the control
and raise the backrest (from the rear , lower the
handle).
Check that the seat has correctly locked
on the floor when returned to the seating
position.
Fixed rear seat and bench
seat
Combi, Business
The different equipment and settings described
hereafter vary according to the version and the
configuration of your vehicle.


The seat has a backrest that may be fixed or
foldable (table position).
The bench seat has a one-piece backrest that
may be fixed or foldable (table position).
For more information on the Seat belts,
refer to the corresponding section.
Access to row 3
(example for an individual seat)

â–º Using the handle, release the rear feet then
tip the seat forward.
â–º

T
o return the seat to the normal position, tip
the seat backwards until the rear feet engage in
their anchorages.
It is not necessary to fold the backrest
(table position) to tip the bench seat and
so access row 3.
Folding the backrest into
the table position
â–º Place the head restraints in the low position. CarM an uals 2 .c o m

60
Ease of use and comfort

â–º From the rear, lower the lever to release the
backrest.
â–º

From the front, raise the lever to release the
backrest.
â–º


Fold the backrest onto the seat cushion.
â–º


T
o return the backrest to the normal position,
raise the lever and pull the backrest up (from the
rear, lower the lever).
Do not leave objects (such as a bag or
toys) on the seat cushion when folding
the backrest.
Tilting
(example of an individual seat)
â–º If your vehicle has the facility , place the
backrest in the table position.


â–º Using the handle, release the rear feet then
tip the seat forward.
â–º

T
o return the seat to the normal position,
unfold the seat backwards until the rear feet
engage in their anchorages.
Removing
(example of an individual seat)
â–º T ip the seat.


â–º Release the front feet using the handles.
â–º Disengage the seat from its anchorages. â–º

Remove the seat through the side door for
row
2 or from the rear for row 3.
Refitting
(example of an individual seat)
â–º
Check that there is no object obstructing the
anchorage points and preventing the feet locking
correctly into place.


â–º Engage the front feet in the anchorage points
on the floor (as shown above).


â–º Lock the front feet using the levers.
â–º T ilt the seat towards the rear until the rear
feet lock into place.
Be careful of passengers' feet during the
manoeuvre.
CarM an uals 2 .c o m

63
Ease of use and comfort
3â–º Check that nothing is obstructing the rails.

â–º Place the front part of the guides on the rails.
â–º T ip the seat to align the rear of the guides in
the rails.
â–º

Slide the seat forwards or backwards until it
engages in the notches.
â–º


Raise the backrest.
Check that the seat has correctly locked
on the floor when returned to the seating
position.
Individual rear seat(s) on
rails
Allure, Business VIP
The different equipment and settings described
hereafter vary according to the version and the
configuration of your vehicle.


The individual seat is fitted with a three-point
inertia reel seat belt.
It can be placed facing forwards or facing
rearwards .
If there is an individual seat facing
rearwards in row 2, ensure that the seat
in row 1 (driver or passenger) is not set too
far back, in order to avoid contact between
the two seats.
This could cause significant wear of the parts
which are in contact.
For more information on the Seat belts,
refer to the corresponding section.
Armrest(s)
The armrest has notches.

â–º Pull the armrest fully up.
â–º Lower it fully .
â–º

Raise the armrest to the desired notched
position.
Adjusting the angle of the backrest
The backrest can be adjusted to several
positions.


â–º To recline the backrest, pull the control
upwards (from the rear, lower the handle).
â–º

Release the control when the desired position
is reached. CarM an uals 2 .c o m

65
Ease of use and comfort
3Refitting

Before refitting the seat in the vehicle,
pull the strap fully to ensure that the
latching mechanism has engaged.


Do not use the strap to lift the seat.
â–º

Check that nothing is obstructing the rails.

â–º Fit the front part on the rails.
â–º T ip the seat to align the rear of the guides in
the rails.
â–º

Slide the seat forwards or backwards until it
engages in the notches.
â–º


Raise the backrest.
Check that the seat has correctly locked
on the floor when returned to the seating
position.
Fixed crew cab

The crew cab is made up of a fixed bench seat,
seat belts, storage compartments (depending
on equipment) and side windows. It is separated
from the loading area by a high-strength
partition.
Rear bench seat
This ergonomic bench seat has three seats.
The two outer seats are fitted with ISOFIX
mountings.
For more information on the ISOFIX
mountings , refer to the corresponding
section.
Storage compartment

If applicable, a storage compartment is available
at the front, underneath the bench seat. CarM an uals 2 .c o m

67
Ease of use and comfort
3â–º Using handle B , guide the movement of the
bench seat until it locks in the folded position.
Bench seat position

â–º To put the bench seat back in place, pull the
strap C to unlock the bench seat, then release
the strap.
â–º

Then, using only the handle

B
, guide the
descent of the backrest to tip the assembly until
it locks in the bench seat position.
Never put your hand underneath the
bench seat to guide it downwards, as you
could get your fingers trapped.
Ensure there are no objects or feet beneath
the bench seat or obstructing the anchorage
system, preventing the assembly from being
correctly locked.
Do not attach anything to the cab fixing
structure.
Do not exceed the number of passengers
indicated on the registration certificate.
In the rear, the load space is intended for
carrying goods only.
It is recommended to place goods or heavy
objects as far forwards as possible in the load
space (towards the cab) and secure them by
means of straps using the stowing rings on
the floor.
The rear seat belt frames are not designed to
secure the load being carried.
Interior fittings
Mats
Fitting

When fitting it on the driver's side, only use the
mountings present on the carpet.
The other mats are simply laid over the carpet.
Removing/refitting
â–º To remove it on the driver's side, move
the seat as far back as possible and give the
fasteners a quarter turn.


â–º To refit it, position the mat and replace the
fasteners, giving them a quarter turn.
â–º

Check that the mat is secured correctly
. CarM an uals 2 .c o m

69
Ease of use and comfort
3Any liquid which could spill risks causing an electrical short circuit and therefore a
potential fire.
"Aircraft" type tables

Fitted to the back of each front seat.

â–º To use the table, lower it fully until it locks in
the low position.
â–º

T
o stow it, raise the table to the high position,
passing the point of resistance.
On the passenger side, do not forget to
fold the table up before placing the seat
in the "table" position.
Do not place hard or heavy objects on
the table. They could become dangerous
projectiles in the event of emergency braking
or impact.
For more information on the Front seats,
and in particular placing the backrest in
the "table" position, refer to the corresponding
section.
12 V socket(s)
Depending on version.







â–º To connect a 12 V accessory (maximum
power: 120 Watts), lift the cover and plug in a
suitable adapter.
Observe the maximum power rating to
avoid damaging the accessory.
The connection of an electrical device not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio reception or
interference with displays in the screens. CarM an uals 2 .c o m

72
Ease of use and comfort
Recommendations on
loading
The weight of the load must comply with the Gross Train Weight (GTW).
For more information on Engine technical
data and towed loads , refer to the
corresponding section.
If you are using a carrying system (roof
bars/roof rack), comply with the
maximum loads associated with this system.
For more information on Roof bars/Roof
rack , refer to the corresponding section.
Make sure that the size, shape and
volume of the loads carried are
compatible with the highway code and safety
regulations and do not impair the driver’s field
of vision.
The load must be evenly distributed in the loading area so as not to interfere
with driving the vehicle.
Place the load close to the side wall panels,
or push it against the side wall panels
between the wheel arches.
However, it is recommended that heavy
objects are placed as close to the cab as
possible as a precaution in case of sharp
braking.
Firmly secure all parts of the load using
the stowing rings on the floor of the
loading area.
For more information on the Interior fittings
and in particular on the stowing rings, refer to
the corresponding section.
To avoid the risk of injury or accident, the load must be made stable so that it
cannot slide, tip over, fall or be projected. To
do this, use only retaining straps that conform
to current standards (DIN, for example).
For more information on putting straps in
place, refer to the manufacturer’s user guide.
To prevent the load from sliding, there must
not be any empty spaces between the load
items and the vehicle wall panels.
As well as the straps, optimise the stability
of the load with stable handling equipment
(wedges, rigid blocks of wood or padding).
When washing your vehicle, never clean
the inside directly using a water jet.
Seating area fittings

High load retaining net
This allows the use of the entire loading capacity,
up to the roof:
–

behind the front seats in row 1, when the rear
seats (and bench seats) in rows 2 and 3 are
folded or removed,
–


behind the rear seats (and bench seats) in row
2, when the rear seats (and bench seats) in row
3 are folded or removed.
Upper fixings

â–º Unclip the anchorage cover in the roof on
each side.
Lower fixings (behind row 1)
If your vehicle has fixed one-piece bench seats
or seats and bench seats:
CarM an uals 2 .c o m

73
Ease of use and comfort
3

â–º On each side in row 2, insert the fixings in the
floor anchorages (as shown above).
If your vehicle has seats and bench seats or
individual seats on rails:


â–º On each side in row 2, insert the fixings in the
floor anchorages then turn them a quarter turn to
lock them in place (as shown above).
Place them as close as possible to the end of
the rail.
Lower fixings (behind row 2)

â–º Use the stowing rings.
Fit the net
Unclip the upper fixing covers and secure the
lower fixings (as previously described).
â–º

Fold (table position) the seats and bench
seats in rows 2 and 3 (according to equipment).
â–º


Close the rear heating and air conditioning
vents (depending on the equipment you have).
â–º


Unroll the high load retaining net.
â–º


Position the net upper fixings in the
corresponding anchorages in the roof (first one
side, then the other).
â–º


Fully extend the straps.
â–º


On each side, attach the bottom fixings of the
net to the lower anchorages (behind row 1) or in
the stowing rings (behind row 2).
â–º


T
ension the straps to extend the net.
â–º

Check that the net is attached securely and
properly extended.
Never use the ISOFIX ring provided for
fixing the strap of a child seat with Top
Tether.
Rear windows in row 2
If fitted to your vehicle, the side windows in row 2
can be opened.


While driving, the windows must be closed or
secured at one of the notches.
â–º

Squeeze the two controls then move the
window sideways.
For more information on the Child lock
on rear windows , refer to the
corresponding section.
Side blinds
Fitted to the windows in row 2, these protect the
passenger compartment from the sun's rays.
CarM an uals 2 .c o m

75
Ease of use and comfort
3Storage

â–º Slide back the cover for access to 11 litres of
storage space.
The storage space can only support a maximum weight of 3 kg; do not exceed
this maximum load in use.
Moving forward or backward

â–º Lift the control (without going beyond the
point of resistance) and slide the assembly
forwards or backwards.
â–º Release the control when it is in the desired
position.
â–º

Check that the table is secured on the runner
.
If this is not the case, move the assembly slightly
to the next notch on the runner.
You can move the table in both the open and stowed position. However, to ensure
safety, it is advised that you handle the
assembly in the stowed position.
For the table to run smoothly, ensure that
no objects are blocking the space used
by the runner on the floor.
Before manoeuvring the table, check that
there is nothing on the table.
Unfolding

â–º Operate the control on the top and pull the
table assembly up until it clicks into place.
â–º

Pull each table top fully up then pivot them on
each side into the horizontal position.
Folding
â–º Raise each table top, going beyond the point
of resistance, to the vertical position.
â–º

Push each table top down into its housing
until it clicks into place.


â–º Push the control then tip the table assembly
downward until it clicks into place.
Before stowing the table tops, check that
they are clear. Before tipping the
assembly down, check that the two table tops
have clicked home in the low position and that
there is nothing in the cup holder area (such
as a can or pen).
Cup holders
Two cups or cans and small objects (such as
a credit card, portable ashtray or pen) can be
carried in the middle of the unfolded table. CarM an uals 2 .c o m