lock Peugeot iOn 2018 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2018, Model line: iOn, Model: Peugeot iOn 2018Pages: 136, PDF Size: 5.79 MB
Page 36 of 136

34
Front demist – defrost
Place the air distribution
adjustment control in this position.
The intake of exterior air is selected (indicator
lamp off) and, depending on equipment, the air
conditioning comes on (indicator lamp lit). Place the temperature adjustment
control between "●" and " H".
Place the air flow adjustment
control in the desired position.
For fast demisting/defrosting, you can also
press the " MAX" button.
Rear screen demist –
defrost
Switching on
F Press this button to demist /
defrost the rear screen and,
depending on version, the door
mirrors. The button indicator
lamp comes on.
Switching off
Demisting/defrosting switches off automatically
to prevent an excessive consumption of
electricity.
F
I
t is possible to stop the
demisting/defrosting operation
before it is switched off
automatically by pressing the
button again. The warning lamp
for the button goes out. Switch off the demisting/defrosting of
the rear screen and door mirrors as
soon as appropriate in order to control
the vehicle's electrical consumption and
optimise its range.
Remote control
(Depending on equipment.)
The remote control can be used to control the
following functions remotely:
-
C
heck the vehicle's charge status.
-
R
echarge programming: start time and
charge duration.
-
A
ctivate the air conditioning functions
(heating, air conditioning, demist - defrost).
To programme recharging, the following
conditions must be met:
-
P
lace the drive selector in position P .
-
P
lace the switch to LOCK .
-
C
onnect the vehicle with the normal
recharging cable.
The remote control range is approximately
100
metres.
Ease of use and comfort
Page 38 of 136

36
If the charge start is programmed without
programming the charge duration, the
battery will be charged fully.
Charge duration
programming
This function is used to set the charging time
for your vehicle.
Switch on the remote control.
Press the MODE button to select the charge
duration programming.This symbol is displayed on the
screen.
Use the arrows to adjust the charging time:
each press adjusts the time in half-hourly
intervals.
Press the on/off button briefly to send the data
to the vehicle.
The charge duration can be programmed
for between 0.5 and 19.5
hours. However,
you can also select the duration "-h": in
this case, charging will stop when the
battery is fully charged. This duration is
the value entered by default. If the charge duration is programmed
without programming the start time, the
battery will be charged immediately for
a duration corresponding to the one
programmed.
Cancelling programmings
With the remote control
Press the charge immediately
button, then press the on/off button
briefly to send the data to the
vehicle.
With the switch
Turn the vehicle's ignition switch to the ON
position then turn it to LOCK .
Any programming carried out with remote
control is cancelled automatically every
time the vehicle is started.
Thermal comfort
programming
This function is used to programme the running
of the:
-
heating,
-
a
ir conditioning,
-
demisting.To programme the heating, air
conditioning or demisting functions, the
following conditions must be met.
-
T
he drive selector is in position P .
-
T
he ignition switch is on LOCK .
-
T
he vehicle is connected with the
normal recharging cable.
-
A
ll the doors are closed properly.
-
T
he battery is sufficiently charged (one
bar minimum).
For maximum efficiency in programming
the thermal comfort, make sure that all the
vehicle's windows are closed.
Ease of use and comfort
Page 40 of 136

38
Malfunctions
Remote control
Warning/
indicator lampStateCausesAction/Observations
Flashes within approximately ten seconds
after switching on the remote control. There is a malfunction.
Switch the remote control off and then on
again.
Flash within approximately one second
after switching on the remote control. Electrical interference is preventing the
remote control or data transmission from
operating.Move away from the inter ference sources.
Flash within approximately ten seconds
after switching on the remote control. The aerial is not extended.
Extend the aerial.
You are outside the range of the remote
control. Move nearer to the vehicle.
The ignition switch is not in the LOCK
position. Turn the switch to LOCK
.
Ease of use and comfort
Page 44 of 136

42
Automatic illumination/
switching off of the headlamps
Automatic illumination
When the lighting control stalk ring is in
the AUTO position, the sidelamps and
dipped beam headlamps are switched on
automatically, without any action on the part of
the driver, when a low level of ambient light is
detected.
As soon as the level of light becomes sufficient
again, the lights are switched off automatically.
The sensor is located at the bottom of the
windscreen.
Do not cover the sunshine sensor, as the
associated functions would no longer be
controlled.
In fog or snow, the sunshine sensor may
detect sufficient light. The headlamps may
not come on automatically.
Automatic switching off
When the lighting control stalk is in the "AUTO"
position, if the ignition key is in the "LOCK" or
"ACC" position or is removed, the headlamps
will automatically switch off when the driver's
door is opened .
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
users, the height of the halogen headlamp
beams must be adjusted according to the load
in the vehicle.
0.Driver only or driver + 1 front
passenger.
1 or 2. 4 passengers (including driver).
3. 4 passengers (including driver) +
maximum authorised load.
4. Driver + maximum authorised load.
The initial setting is position " 0".
Wiper control stalk
The wipers are controlled directly by the driver
using control A and ring B .
In wintry conditions, remove snow, ice
or frost present on the windscreen,
around the wiper arms and blades and
the windscreen seal before operating the
wipers.
Do not operate the wipers on a dry
windscreen. Under extremely hot or cold
conditions, ensure that the wiper blades
are not stuck to the windscreen before
operating the wipers.
Lighting and visibility
Page 45 of 136

43
Windscreen wipers
A.Wiping speed control lever: raise
or lower the lever to the desired
position.
Single wipe.
Of f.
Intermittent (manually adjustable
speed).
Slow.
Fast.
B. Intermittent adjustment ring.
F
T
urn this ring to increase or
decrease wiping frequency in
intermittent mode.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for a
preset time.
Rear wiper
C. Rear wiper selection ring.
Of f.
Intermittent wiping.
The wiper wipes twice then switches to
intermittent mode with an inter val of a few
seconds. Wash-wipe.
Hold the ring in this position to operate the
screenwash and to carry out several wipes with
the wipers.
Courtesy lamp
Position 1 "ON"
The courtesy lamp is permanently on.
Position 2 "●"
The courtesy lamp comes on when a door or
the boot is opened; when the door or boot is
closed again, the lighting dims gradually for a
few seconds before going out.
However, the courtesy lamp goes out
immediately when the doors and boot are
closed and you lock the vehicle from the inside
or with the remote control.
4
Lighting and visibility
Page 50 of 136

48
** As per the geographic coverage of "Peugeot Connect SOS", "Peugeot Connect
Assistance" and the official national
language chosen by the owner of the vehicle.
The list of countries covered and PEUGEOT
CONNECT services is available from dealers
or on the website for your country.
Geo-location
If you purchased your vehicle outside the
PEUGEOT dealer network, we invite you
to have a dealer check the configuration of
these ser vices and, if desired, modify it to
suit your wishes.
In a multi-lingual country, configuration is
possible in the official national language
of your choice. For technical reasons and in particular
to improve the quality of PEUGEOT
CONNECT ser vices to customers, the
manufacturer reser ves the right to carry
out updates to the vehicle's on-board
telematic system.
The cancellation is confirmed by a voice
message.
You can deactivate geo-location by
simultaneously pressing the "Peugeot Connect
SOS" and "Peugeot Connect Assistance"
buttons, followed by pressing "Peugeot
Connect Assistance" to confirm.
To reactivate geolocation, simultaneously press
the "Peugeot Connect SOS" and "Peugeot
Connect Assistance" buttons again, followed
by a press on "Peugeot Connect Assistance"
to confirm.
Braking assistance
systems
Group of supplementary systems which help
you to obtain optimum braking in complete
safety in emergency situations:
-
a
nti-lock braking system (ABS),
-
e
lectronic brake force distribution (EBFD),
-
em
ergency braking assistance (EBA).
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and
manoeuvrability of your vehicle when braking,
in particular on poor or slippery sur faces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself
felt by slight vibrations of the brake pedal.If you need to brake in an emergency,
press very firmly and maintain this
pressure.
Malfunction
Stationary vehicle If this warning lamp comes on,
it indicates an anti-lock braking
system malfunction that could cause
control of the vehicle to be lost
during braking.
Contact a PEUGEOT dealer or a qualified
workshop.
Safety
Page 51 of 136

49
The warning lamp comes on for a few
seconds when switching on (ON position).
If it does not go out or come on, contact a
PEUGEOT dealer or a qualified workshop.
Moving vehicle If this warning lamp remains on
constantly, it indicates an anti-lock
braking system malfunction that
could cause control of the vehicle to
be lost during braking.
You must stop as soon as it is safe to do so.
Contact a PEUGEOT dealer or a qualified
workshop.
If both these warning lamps come
on, they indicate a malfunction in the
electronic brake force distribution
that could cause control of the
vehicle to be lost during braking.
You must stop as soon as it is safe to do so.
Contact a PEUGEOT dealer or a qualified
workshop.
When replacing wheels (tyres and rims),
ensure that they comply with manufacturer
recommendations.Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more
quickly, thus reducing the stopping distance.
Activation
It is triggered by the speed at which the brake
pedal is pressed.
The effect of this is a reduction in the
resistance of the pedal and an increase in
braking efficiency. In emergency braking, press very firmly
and maintain this pressure.
Trajectory control systems
Anti-slip regulation (ASR)
and dynamic stability
control (DSC)
The anti-slip regulation (also known as traction
control) optimises traction to prevent skidding of
the wheels, by acting on the brakes of the driving
wheels and on the engine.
The stability control acts on the brake of one
or more wheels and on the engine to keep the
vehicle on the trajectory required by the driver,
within the limits of the laws of physics.
Activation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument
panel.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
the ASR and DSC systems, so that the wheels
can regain grip.
F
P
ress this button until the corresponding
symbol appears in the instrument panel.
The display of this symbol indicates
that the ASR and DSC systems are
deactivated.
5
Safety
Page 55 of 136

53
Advice
The driver must ensure that passengers use
the seat belts correctly and that they are all
restrained securely before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not completely fulfil their role.
The seat belts are equipped with an
inertia reel which allows the strap length
to automatically adjust to your shape. The
seat belt returns to its storage position
automatically when it is not used.
Before and after use, ensure that the seat belt
is reeled in correctly.
The lower part of the strap must be positioned
as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels are fitted with a device which
automatically locks the strap in the event
of a collision or emergency braking or if the
vehicle rolls over. You can release the device
by pulling the strap firmly and then releasing it
so that it reels in slightly.In order to be effective, a seat belt:
-
M ust be tightened as close to the body as
possible,
-
M
ust be pulled in front of you with a
smooth movement, ensuring that it is not
twisted,
-
M
ust only be used to secure one person,
-
M
ust not show signs of tearing or fraying,
-
M
ust not be changed or modified, in order
to avoid affecting its performance.
In accordance with current safety regulations,
for all repairs on your vehicle's seat belts, go
to a qualified workshop with the skills and
equipment needed, which a PEUGEOT dealer
is able to provide.
Have your seat belts checked regularly by a
PEUGEOT dealer or by a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy water or
a textile cleaning product, sold by PEUGEOT
dealers.
After folding or moving a seat or a rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly. Instructions for children
Use a suitable child seat, if the passenger is
less than 12
years old or shorter than one and
a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap.
For more information on Child seats , refer to
the corresponding section.
In the event of an impact
Depending on the nature and seriousness
of the impacts , the pyrotechnic device may
trigger before and independently of airbag
deployment. Deployment of the pretensioners
is accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp comes
on.
After an impact, have the seat belt system
checked and, if necessary, replaced
by a PEUGEOT dealer or a qualified
workshop.
5
Safety
Page 68 of 136

66
Advice on child seats
The incorrect installation of a child seat in a
vehicle compromises the child's protection in
the event of an accident.
Ensure that there is no seat belt or seat belt
buckle under the child seat, as this could
destabilise it.
Remember to fasten the seat belts or the
child seat harnesses keeping the slack
relative to the child's body to a minimum,
even for short journeys.
When installing a child seat using the seat
belt, ensure that the seat belt is tightened
correctly on the child seat and that it secures
the child seat firmly on the seat of your
vehicle. If your passenger seat is adjustable,
move it for wards if necessary.
At rear seating places, always leave sufficient
space between the front seat and:
-
a "
rear ward facing" child seat,
-
t
he feet of a child seated in a "for ward
facing" child seat.
To do this, move the front seat for wards
and, if necessary, move its backrest into the
upright position. For optimal installation of the "forward facing"
child seat, verify that its backrest is as close
as possible to the backrest of the vehicle
seat, or if possible in contact with it.
You must remove the head restraint before
installing a child seat with backrest on
a passenger seat. Ensure that the head
restraint is stored or attached securely to
prevent it from being thrown around the
vehicle in the event of sharp braking. Refit the
head restraint when the child seat is removed.
Installing a booster seat
The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs.
PEUGEOT recommends using a booster seat
with a backrest, equipped with a belt guide at
shoulder level.
As a safety precaution, do not leave:
-
a c
hild or children alone and unattended in
a vehicle,
-
a c
hild or an animal in a car which is
exposed to the sun, with the windows
closed,
-
t
he keys within reach of children inside the
vehicle.
To prevent accidental opening of the doors
and rear windows, use the child lock.
Take care not to open the rear windows by
more than one third.
To protect young children from the rays of the
sun, fit side blinds on the rear windows.
Children in the front
The legislation on carrying a child on the front
passenger seat is specific to each country.
Refer to the legislation in force in your
c o u nt r y.
Deactivate the passenger airbag when a
"rear ward facing" child seat is installed on the
front passenger seat. Otherwise, the child
may be seriously injured or killed were the
airbag to be deployed.
Safety
Page 69 of 136

67
Child lock
Mechanical system to prevent opening of a rear
door using its interior control.
The control is located on the edge of each rear
d o o r.
Locking
Unlocking
F Move control A up to position 2.
F
M
ove control A down to position 1
.
5
Safety