service reset Peugeot iOn 2018 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2018, Model line: iOn, Model: Peugeot iOn 2018Pages: 136, PDF Size: 5.79 MB
Page 9 of 136
7
Instrument panel
Dials
1.Main battery state of charge indicator.
Reminder of the drive selector position.
2. Energy consumption/generation indicator.
3. Speedometer.
Engine brake temporary reduction
i n d i c a t o r.
4. Display screen.
Display screen
A.Total distance recorder.
B. Trip distance recorder ( journey A or B).
C. Instrument panel lighting dimmer.
D. Distance remaining until service due.
E. Time remaining until service due.
F. Under-inflation detection.
G. Remaining range indicator.
Warning and indicator lamps
Visual identifiers informing the driver that
a system is in operation, switched off (on/
off indicator lamps) or has developed a fault
(warning lamp).
When the ignition is switched on
Certain warning lamps come on for a few
seconds when the vehicle's ignition is switched
on.
When the vehicle is started, these same
warning lamps should go off.
If they remain on, before driving refer to the
information on the warning lamp concerned.
Associated warnings
The illumination of certain warning lamps may
be accompanied by an audible signal.
There are two types of lighting for warning
lamps, fixed (continuous) or flashing.
Certain warning lamps may come on in
one of two modes. Only by relating the
type of lighting to the operating status of
the vehicle can it be ascertained whether
the situation is normal or whether a fault
has occurred.
5.
Display screen management button.
Displays the different functions
su c c e s s i ve l y.
Resets the selected function to zero (trip
distance recorder or service indicator).
Sets the lighting dimmer intensity.
Panel that brings together the different dials
and vehicle operation indicator lamps.
1
Dashboard instruments
Page 18 of 136
16
Lighting dimmer
System that allows the brightness of the
instruments and controls to be adjusted
manually to suit the ambient light level.
With the headlamps on or off, press button A to
select the function, then hold it down to adjust
the brightness of the instruments and controls
lighting to "day" or "night".
The brightness of the lighting increases every
time you press button A.
When the lighting reaches the maximum
setting, press again to move to the minimum
setting.
Release button A as soon as the lighting
reaches the desired brightness.
The setting is registered as soon as you
release button A and is stored when the ignition
switch is turned to OFF.
Service indicator
System which informs the driver when the
next ser vice is due, in accordance with the
manufacturer's servicing schedule.
This due date is calculated from the last reset
of the service indicator.
There are two different ways to indicate when
the next ser vice is due:
-
r
emaining distance (in kilometres or miles),
-
t
ime (in months) left before the next
service.
Once the ignition is switched on, press
button
A successively until the ser vice indicator
is displayed in the desired units.
Operation
1. The display shows the distance or time
remaining before the next service.
2. The display shows that the ser vice is due.
Each time the ignition is switched on, the
ser vice spanner is displayed for a few
seconds to notify you that the ser vice
must be carried out very soon.
3. Once the ser vice has been completed,
the distance or the time remaining before
the next ser vice is displayed.
Dashboard instruments
Page 19 of 136
17
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
F
T
urn off the ignition (switch to LOCK or
ACC position).
F
P
ress the reset button A in succession until
the service indicator is displayed.
F
P
ress and hold the reset button down for a
few seconds to make the spanner flash .
F
P
ress the reset button whilst the spanner
is flashing to move the display " ---" to
" CLEAR ".
The distance (or the time) remaining before
the next ser vice is displayed. The distance "
---" indicating that the
ser vice is now due is reset automatically
after a certain time and a certain distance
travelled. The display will then indicate the
remaining time before the next service.
Under-inflation detection
You must reinitialise the under-inflation
detection system after adjusting one or more
tyre pressures and after changing one or more
wheels.
The procedure for this is as follows.
F
P
ress button A to select the system.
F
P
ress and hold button A down for at least
three seconds .
An audible signal sounds and the under-
inflation warning lamp flashes slowly until
reinitialisation has been completed.
1
Dashboard instruments
Page 125 of 136
1
1
2
1
2
KENWOOD – KDC-X7000DAB
As a safety measure, the vehicle must
be stationary when the driver carries
out operations that require sustained
attention.Short press: on.
Long press: off.
Rotate: set the audio volume,
navigate in a list.
Press: confirm.
Change the audio source.
Short press: accept an incoming
call, switch between two calls, enter
Bluetooth mode.
Long press: smartphone voice
commands via the system.
Short press: find a ser vice.
Long press: update list of stations
received.
Abandon the current operation.
Go up one level in the menu.
Reject or end a call.Select an analogue band FM1/FM2/
FM 3 / M W/ LW.
Select a digital band DB1/DB2/DB3.
Navigate in a list.
Change the search method
(automatic or manual).
Fit the control panel.
Remove the control panel. Short press: find a radio station,
frequency or service, find the
previous/next track or file, navigate
in a list.
Long press: fast for ward or rewind.
Short press: select a preset radio
station.
Long press: add a radio station to
presets.
For more information, refer to the KENWOOD
user guide provided with the system.
.
KENWOOD - KDC-X7000DAB