Lock release Peugeot Partner 2019 Owner's Manual

39
Programming
Without audio system
With audio system or touch screen
Activation or deactivation of the
selectivity between the driver's
door and the other doors and
the boot is done via the vehicle
configuration menu.
Complete unlocking
With the key
F To activate this selectivity
between cab and loading area
or to deactivate this selectivity
and return to total unlocking,
switch the ignition on and press
this button for more than two
seconds.
An audible signal and, depending on
equipment, a display message, confirm that the
request has been acknowledged. F
To
completely unlock the vehicle, insert the
key in the lock then turn it towards the front
of the vehicle.
F
T
hen pull the handle to open the door.
If fitted to your vehicle, the alarm is not
deactivated. Opening a door will trigger the
alarm, which can be stopped by switching the
ignition on.Using the remote control
F Press one of these buttons to unlock the vehicle.
If your vehicle is so equipped,
pressing and holding this button
allows the windows to be opened.
The window stops when you
release the control.
Unlocking is confirmed by rapid flashing
of the direction indicators for around
2


seconds.
At the same time, depending on your
version, the door mirrors unfold.
With the Keyless Entry and
Starting on your person
F To unlock the vehicle, remote control on your person and in recognition zone A , pass
your hand behind one of the door handles
(front doors, manual sliding side doors or
side-hinged doors).
F

P
ull the handle to open the corresponding
d o o r.
F

T
o unlock the vehicle, remote control in the
recognition zone A , run a hand behind the
handle of the side-hinged door.
With side-hinged doors
2
Access

40
Selective unlocking
Using the remote control
F To unlock just the cab doors,
press this button once.
F

T
o unlock the doors of the
loading area (side and rear),
press this button a second time.
or F

P
ress this button on the remote
control to unlock only the
loading area .
If your vehicle is so equipped,
pressing and holding this
button allows the windows to be
opened. The window stops when
you release the control.
Unlocking is confirmed by rapid flashing
of the direction indicators for around
2


seconds.
At the same time, depending on your
version, the door mirrors unfold.
With Keyless Entry and Starting
on your person
F To unlock the cab alone, while
having the remote control on
your person in the recognition
zone A , pass your hand behind
the handle of the driver's door.
With tailgate
F To unlock the vehicle, with the remote control in recognition zone A , press the
tailgate release control.
F

Ra
ise the tailgate.
F

T
hen pull the handle to open it.
F
T
o unlock the cab alone, while
having the remote control on
your person in the recognition
zone B , pass your hand behind
the handle of the driver's door.
F

P
ull the handle to open the cab.
The door locking state of the loading area
remains unchanged.
Access

41
Depending on version, the door mirrors
unfold only when the cab is unlocked, and
the alarm is deactivated.
Unlocking
With the key
F To completely unlock the vehicle, insert the
key in the lock then turn it towards the front
of the vehicle.
F

T
hen pull the handle to open the door.
Using the remote control
F Press this button to unlock the vehicle.
If fitted to your vehicle, pressing
and holding this button opens
the windows. The window stops
when you release the control.
With the K eyless Entry and
Starting on your person
(front doors, manual sliding side doors or
side-hinged doors).
F

P
ull the handle to open the corresponding
d o o r.
With tailgate
With side-hinged doors
F To unlock the vehicle, remote control in the
recognition zone A , run a hand behind the
handle of the side-hinged door.
F

T
hen pull the handle to open it.
F

T

o unlock the loading area
alone, with
the remote control on your person in the
recognition zone A , B or C, pass your hand
behind one of the handles of the left-hand
side door, right-hand side door or the rear
door (the left-hand hinged door or the
tailgate).
F

P

ull the handle to open the loading area.
Unlocking is signalled by rapid flashing of
the direction indicators for a few seconds.
Depending on version, the door mirrors
unfold and the alarm is deactivated. If fitted to your vehicle, the alarm is not
deactivated. Opening a door will trigger the
alarm, which can be stopped by switching the
ignition on.
F

T

o unlock the vehicle, remote control on
your person and in recognition zone A , pass
your hand behind one of the door handles
2
Access

42
Locking
With the key
F To lock the vehicle, insert the key in the lock then turn it towards the rear of the vehicle.
Using the remote control
F To lock the vehicle, press this button. If fitted to your vehicle, pressing
and holding this button closes the
windows. The window stops when
you release the control.
Ensure that no person or object prevents
the correct closing of the windows.
Be particularly aware of children when
operating the windows.
If your vehicle is not fitted with an alarm,
the locking/deadlocking is signalled by the
fixed illumination of the direction indicators
for about two seconds.
Depending on your version, the door
mirrors fold at the same time.
With the K eyless Entry and
Starting "on your person"
F To unlock the vehicle, with the remote
control in recognition zone A , press the
tailgate release control.
F

Ra
ise the tailgate.
F

T
o lock the vehicle, with the remote control
in the recognition zone A , press with a
finger or thumb on the markings of one of
the front or rear door handles.With side-hinged doors/tailgate
Ensure that no person or object prevents
the correct closing of the windows.
Be particularly aware of children when
operating the windows.
F

T
o lock the vehicle, with the remote control
in the recognition zone A , press the left-
hand door/tailgate locking control.
If your vehicle is so equipped,
pressing and holding the locking
controls allows the windows to
be closed. If you release the
control, the window stops.
Access

43
If a door is not properly closed (except
the right-hand door with side-hinged
rear doors):
-
v
ehicle stationary and engine
running, this warning lamp comes
on, accompanied by an alert
message for a few seconds,
-

v
ehicle moving (speed above
6
mph (10 km/h)), this warning
lamp comes on, accompanied
by an audible signal and an alert
message for a few seconds.
Deadlocking
With the key
F To deadlock the vehicle, insert the key in the lock then turn it towards the rear.
F
Then within five seconds , turn the key
towards the rear again.
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual central
control button.
Therefore, never leave anyone inside the
vehicle when it is deadlocked.
With the remote control
F To deadlock the vehicle, press this button.
F
Then within five seconds after
locking , press this button again.
Depending on the version you have, the
electric door mirrors fold at the same time.
With the Keyless Entry and
Starting "on your person"
With side-hinged doors/tailgate
F To lock the vehicle, with the remote control in the recognition zone A , press with a
finger or thumb on the markings of one of
the front or rear door handles.
F

T
o deadlock the vehicle, press the marking
again within five seconds.
If your vehicle is so equipped,
pressing and holding the locking
controls allows the windows to
be closed. If you release the
button, the window stops.
Driving with the doors locked could make
it more difficult for the emergency ser vices
to enter the vehicle in an emergency.
As a safety measure (with children on
board), never leave the vehicle without
taking your remote control with you, even
for a short period.
F

T
o lock the vehicle, with the remote control
in recognition zone A , press the left-hand
door/tailgate locking control.
2
Access

52
In the case of a steep slope, the door
may be driven by its own weight and
as a consequence may open or close
violently.
Take care not to leave the vehicle on a
steep slope with the door(s) open without
supervision. If this advice is not followed,
injuries or damage may occur if a person
or an object is trapped or caught.
Rear roof flap
This roof flap at the rear is compatible only with
side-hinged doors.
To open the rear roof flap:
F

L
ift the black paddle of the toggle.
F

R
elax the toggle by pressing on the rear
roof flap (downwards) then release the
hook.
F

L
ift the rear roof flap. Never drive without the props in place.
Support bar
A support bar is available for transporting long
loads, after opening the rear roof flap.
Never attach any load to the rear roof flap.
The rear bumper has been reinforced to
serve as a step when entering the vehicle.
F
F
old back the support bar by lifting the lever.
F

G
uide it to the door pillar.
F

S
upport the long loads to be transported,
lift them and reposition the support bar with
one hand. Never drive without the support bar in
place.
The rear doors will only lock when the
support bar is installed.
When the rear roof flap is open, take care
when driving where height is restricted.
Never rest loads directly on the rear doors.
Comply with the usual indications for
warning other drivers.
Reser ve the use of the rear roof flap for
short journeys.
To close the rear roof flap:
F

C
heck that the support bar is properly
secured.
F
L
ower the rear roof flap.
F
W
hile pressing on the rear roof flap
(downwards), take the two spring rings and
then place the hook in its housing.
F
L
ower the black paddle to lock the rear roof
flap.
Locking the rear roof flap ensures tight contact
with the seal and guarantees sealing with no
noise.
F
M
ove past the point of resistance to lock the
rear roof flap with the support props. F
E
nsure that it is secured correctly by
pressing the handle downwards past the
point of resistance and secure the loads
f i r m l y.
The side supports can be used as hooking
points.
Access

55
Electric windows
1.Left electric window control.
2. Right electric window control.
Manual mode
Automatic mode
Press or pull the control fully, beyond the
resistance point. The window opens or closes
completely when the switch is released.
Pressing the switch again stops the movement
of the window. The electric window functions
are deactivated for approximately 45
seconds
after switching off the ignition.
Safety anti-pinch
Malfunction
When the ignition is switched on, fixed
illumination of the red indicator lamp in the
button indicates a malfunction of the system.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Automatic activation
(Depending on the country of sale)
The system is activated automatically 2

m
inutes
after the last door or the boot is closed.
F

T
o avoid triggering the alarm on entering
the vehicle, first press the unlocking button
on the remote control or unlock the vehicle
using the "
K

eyless Entry and Starting"
system. Press or pull the control, without going past the
point of resistance. The window stops as soon
as the control is released.
If your vehicle is fitted with the safety anti-pinch
function, when the window rises and meets an
obstacle, it stops and partially lowers.
Reinitialisation
Following reconnection of the battery, the anti-
pinch safety function must be reinitialised.
F

L
ower the window fully, then raise it, it will
rise in steps of a few centimetres each time
the control is pressed.
F

R
epeat the operation until the window is
fully closed.
F

C
ontinue to pull the control upwards for
at least one second after reaching this
position, window closed.
The safety anti-pinch does not operate
while doing this.
Failure of the remote control
To deactivate the monitoring functions:
F u nlock the vehicle using the key (integral to
the remote control) in the driver's door lock,
F

o
pen the door; the alarm is triggered,
F

s
witch on the ignition; the alarm stops; the
indicator lamp in the button goes off.
Locking the vehicle without
activating the alarm
F Lock or deadlock the vehicle using the key (integral to the remote control) in the driver's
door lock. In the event of unwanted opening of the window
on closing, press the control until the window
opens completely. Within 4
seconds, pull the
control until the window closes.
The safety anti-pinch does not operate while
doing this.
2
Access

57
Steering wheel adjustment
F When stationary, pull the control lever to
release the steering wheel.
F

A
djust the height and reach to suit your
driving position.
F

L
ower the control lever to lock the steering
wheel.
As a safety precaution, these operations
must only be carried out while the vehicle
is stationary.
Mirrors
Door mirrors
Adjustment
As a safety measure, the mirrors should
be adjusted to reduce the blind spots.
The objects obser ved are, in reality, closer
than they appear.
Take this into account when assessing
the distance of vehicles approaching from
behind.
Manual folding
You can manually fold the mirrors (parking
obstruction, narrow garage, etc.)
F
T
urn the mirror towards the vehicle.
Electric folding
F Move control A or turn control C (depending on the version you have) to the right or to
the left to select the corresponding mirror.
F

M
ove control B or C (depending on
the version you have) in any of the four
directions to adjust.
F

R
eturn control A or C (depending on the
version you have) to its centre position.
If your vehicle is fitted with this function, the
mirrors can be folded electrically from the inside,
with the vehicle parked and the ignition on:
Electric unfolding
The electric unfolding of the mirrors is via
the remote control or the key when unlocking
the vehicle. Unless folding was selected with
control A , pull the control back again to the
central position.
The folding/unfolding on locking/unlocking
can be deactivated. Contact a PEUGEOT
dealer or a qualified workshop.
If necessary, it is possible to fold the
mirrors manually. F

P
lace control A in the centre
position.
F
P
ull control A back.
From the outside, lock the vehicle using the
remote control or the key.
3
Ease of use and comfort

63
Never put your hand underneath the seat
cushion to guide the seat downwards or
upwards, you could get your fingers trapped.
Always just use the strap.
Before carrying out these manoeuvres, check
that nothing and nobody is obstructing the
moving elements and their locking.
Folded position
This position allows the transport of high loads
inside the cab.
To replace the seat, push on the yellow crank
under the seat and lower the assembly until the
seat locks into position on the floor.F

L
ift the yellow crank at the base of the seat
to unlock and lift the assembly into folded
position (seat raised against the backrest)
until it locks.
Never put your hand underneath the seat
cushion to guide the seat downwards or
upwards, you could get your fingers trapped.
Place your hand on the front of the seat
cushion.
Before carrying out these manipulations,
check that nothing and nobody is obstructing
the moving elements and their locking.
Rear bench seat
For safety reasons, seat adjustments
must only be made when the vehicle is
stationary.
Folding the backrests
First steps:
F l ower the head restraints,
F

i
f necessary, move the front seats for ward,
F

c
heck that nothing or no person might
inter fere with the folding of the backrests
(clothing, luggage, etc.),
F

c
heck that the outer seat belts are lying flat
on the backrests. The folding of the backrest is
accompanied by a slight lowering of the
corresponding seat cushion.
When the backrest is released, the red
indicator is visible in the release grips on
the outer seats.
F
T
urn backrest release grip 1.
F

G
uide the backrest down to the horizontal
position.
3
Ease of use and comfort

70
Multi-Flex bench seatRemove the flap
F While holding the flap with one hand, turn the control at the top of the flap with the
other hand to release it.
F

L
ower the flap to remove it from its housing. F

S
tow it behind the driver’s seat, turning the
control at the top of the flap upwards to lock
it.
It has the 2-seat front bench seat and a
removable flap.
For more information on the 2-seat front
bench seat
, refer to the corresponding section.
A partition located on the floor behind the front
seats protects the driver and front passengers
against the risk of load movement.
A movable flap on this partition can be removed
to allow long items to be loaded.
A protective cover is provided in the vehicle to
ensure that long items can be transported in
complete safety.
Ease of use and comfort