maintenance Peugeot RCZ 2011 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2011, Model line: RCZ, Model: Peugeot RCZ 2011Pages: 276, PDF Size: 51.24 MB
Page 5 of 276
CONTENTS
Steering lock - Starting 124
Parking brake 125
Hill start assist 126Manual gearbox 127
Gear shift indicator 128
Automatic gearbox 129Speed limiter 133
Cruise control 136
Parking sensors 139
Fuel tank 143
Bonnet 145
Petrol engines 146Diesel engine 147
Running out of fuel (Diesel) 148
Checking levels 149Checks 151
Temporary puncture repair kit 153
Changing a wheel 160
Changing a wiper blade 164Energy economy mode 165
Battery 166
Changing a bulb 168
Changing a fuse 175Towing a vehicle 182
Towing a trailer 184
Cleaning and maintenance 186
Accessories 187
6/DRIVING 124-141
7/CHECKS 142-152
8/PRACTICAL INFORMATION 153-188
ALPHABETICAL INDEX 261-265
VISUAL SEARCH 266-269
Petrol engines 189
Weights (petrol) 190Diesel engine 191
Weights (Diesel) 192Dimensions 193
Identification markings 194
9/TECHNICAL DATA 189-194
Emergency or assistance 195 Peugeot Connect Media 199 Peugeot Connect Sound 243
10/AUDIO EQUIPMENT AND TELEMATICS 195-260
Page 6 of 276
4
EXTERIOR
1 Welcome lighting
This additional exterior and
interior lighting, controlled
remotely, makes your approach to
the vehicle easier when the light
is poor.
2 Directional lighting
This lighting automatically
provides additional visibility when
cornering. 78
94
106
5 Temporary tyre repair kit
This kit is a complete system,
consisting of a compressor
and a sealant cartridge, for the
temporary repair of a tyre.
153
3 Active spoiler
This system improves the
aerodynamics of the vehicle.
4 Front and rear parking
sensors
This system warns you of any
obstacles detected in front of or
behind the vehicle when parking.
139
Aluminium arches
For maintenance of these
arches, do not use a dry
cloth with an abrasive
product. Use a sponge and
soapy water.
Page 9 of 276
ON
O
FFA
IRB
AG
PASS
FAMILIARISATION
INTERIOR
1 Interior mood lighting
This dimmed lighting of the passenger
compartment facilitates visibility inside the
vehicle when the light is poor.
78
2 Audio and telematics systems
This equipment benefi ts from the latest
technology: MP3 compatible Peugeot Connect
Sound, Bluetooth, Peugeot Connect Media
with 16/9 retractable colour screen, JBL audio
system, auxiliary sockets.
Peugeot Connect Media
Peugeot Connect Sound/Bluetooth
199
243
4 Active spoiler
This automatic system can be controlled
manually by means of this control on the
centre console.
106
3 Dual-zone digital air conditioning
This systems allows different levels of comfort
to be set for the driver and front passenger.
It then controls these levels automatically
according to the ambient conditions.
74
PEUGEOT Techno PVC
For maintenance of this covering, do not
use solvent or detergent with a dry cloth.
Remove dust fi rst, then use a soft cloth
and soapy water. Dry using another soft
cloth.
Page 23 of 276
LIMIT THE CAUSES OF
EXCESS CONSUMPTION
Spread loads throughout the vehicle; place
the heaviest items in the bottom of the boot,
as close as possible to the rear seats.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof rack,
bicycle carrier, trailer...). Use a roof box in
preference.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and
refi t your summer tyres.
OBSERVE THE RECOMMENDATIONS
ON MAINTENANCE
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the tyres on
any trailer or caravan.
Have your vehicle serviced regularly (engine
oil, oil fi lter, air fi lter...) and observe the
schedule of operations recommended by the
manufacturer.
When refuelling, do not continue after the 3 rd
cut-off of the nozzle to avoid any overfl ow.
At the wheel of your new vehicle, it is only
after the fi rst 1 800 miles (3 000 kilometres)
that you will see the fuel consumption settle
down to a consistent average.
Page 37 of 276
1/
INSTRUMENTS AND CONTROLS
SERVICE INDICATOR
This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator
zero reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service.
More than 1 800 miles (3 000 km) remain before the next service is due
When the ignition is switched on, no service information appears on the
instrument panel central screen.
Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For 7 seconds after the ignition is switched on, the spanner symbolising
the service operations comes on. The instrument panel central screen
indicates the distance remaining before the next service is due.
Example:
1 700 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example:
500 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:
The spanner remains on
on the small
screen to indicate that a service must be
carried out soon.
Maintenance due in
1700 miles or
9 months
1700miles
Maintenance due in
500 miles or
2 months
500miles
Page 75 of 276
3/
EASE OF USE AND COMFORT
In order for these systems to be fully effective, follow the operation
and maintenance guidelines below:
)
To obtain an even air distribution, take care not to obstruct
the exterior air intake grilles located at the base of the
windscreen, the nozzles, the vents and the air outlets, as well
as the air extractor located in the boot.
)
Do not cover the sunshine sensor, located on the dashboard;
this is used for regulation of the air conditioning system.
)
Operate the air conditioning system for at least 5 to 10 minutes,
once or twice a month to keep it in good working order.
)
Ensure that the passenger compartment fi lter is in good
condition and have the fi lter elements replaced regularly (refer
to the "Checks" section).
We recommend the use of a combined passenger
compartment fi lter. Thanks to its special active additive,
it contributes to the purifi cation of the air breathed by the
occupants and the cleanliness of the passenger compartment
(reduction of allergic symptoms, bad odours and greasy
deposits).
)
To ensure correct operation of the air conditioning system, you
are also advised to refer to the Warranty and Maintenance
Record for information on when it should be checked.
)
If the system does not produce cold air, switch it off and
contact a PEUGEOT dealer or a qualifi ed workshop.
When towing the maximum load on a steep gradient in high
temperatures, switching off the air conditioning increases the
available engine power and so improves towing performance.
The condensation created by the air conditioning results in a
discharge of water under the vehicle which is perfectly normal.
If after an extended stop in sunshine, the interior temperature is
very high, fi rst ventilate the cabin for a few moments.
Put the air fl ow control at a setting high enough to quickly change
the air in the cabin.
The air conditioning system does not contain chlorine and does
not present any danger to the ozone layer.
RECOMMENDATIONS FOR VENTILATION AND AIR CONDITIONING
Page 109 of 276
5/
SAFETY
Before operating the spoiler, ensure that no one is in the proximity
of the moving parts to avoid any risk of injury.
Nevertheless, in the event of pinching, you must reverse the
movement of the spoiler. To do this, release the control button
then press it again to raise the spoiler.
MAINTENANCE
To maintain the spoiler, with the vehicle stationary, ignition on:
)
raise the spoiler to the maximum position B
by pressing the button
briefl y,
)
once the cleaning is complete, retract the spoiler: press and hold
the button until the end of the manoeuvre.
The keep this system in good working order, check the spoiler and its
housing periodically preventing the unwanted accumulation of leaves,
ice or snow.
OPERATING FAULT
If the control system fails, the indicator lamp in the control button
fl ashes, accompanied by an audible signal and a message in the
screen. As a safety precaution, the spoiler rises to the maximum
position, regardless of the speed of the vehicle.
If the problem persists and you wish to retract the spoiler:
)
stop where it is safe to do so,
)
switch off the ignition,
)
switch the ignition on again.
If the indicator lamp no longer fl ashes, the failure was temporary, the
system has resumed normal operation. To retract the spoiler, refer to
the paragraph "To exit from manual mode".
If the indicator lamp fl ashes again and the spoiler is still raised, the
system is still faulty.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
In the event of a system operating fault (e.g. jamming of the spoiler), the
indicator lamp in the control button fl ashes, accompanied by an audible
signal and a message in the screen. For safety reasons, do not exceed
a speed of 85 mph (140 km/h).
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
Before washing the vehicle, always retract the spoiler into its
housing.
Keep the end of the high-pressure nozzle at least 1 metre from the
spoiler housing.
Never press on the spoiler to close the boot or push the vehicle as
this may damage it.
The installation of load-carrying accessories on the vehicle limits
the effectiveness of the spoiler.
Do not install load carrying accessories which are not
recommended by PEUGEOT.
To exit from manual mode:
)
press the button briefl y: the indicator lamp on the button goes off
(return to automatic mode).
At speeds below 6 mph (10 km/h), the spoiler stays in the open
position. It retracts automatically as soon as the vehicle exceeds
this speed threshold.
Page 132 of 276
3
3
130
DISPLAYS IN THE INSTRUMENT PANEL
When you move the lever in the gate to select a position, the
corresponding indicator lamp is displayed in the instrument panel.
P.
Park
R.
Reverse
N.
Neutral
D1... D6.
Drive (Automatic driving)
S.
Sport
programme
7
. Snow
programme
M1... M6.
Manual (Sequential driving)
-.
Invalid value during manual operation
MOVING OFF
)
Apply the parking brake.
)
Select position P
or N
.
)
Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.
)
With the engine running, press the brake pedal.
)
Release the parking brake.
)
Select position R
, D
or M
,
)
Gradually release the brake pedal.
The vehicle moves off immediately.
If position N
is engaged inadvertently while driving, allow the
engine to return to idle then engage position D
to accelerate.
When the engine is running at idle, with the brakes released,
if position R
, D
or M
is selected, the vehicle moves even without
the accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P
.
A message appears if you try to move the gear lever from
position P
to another position without pressing the brake pedal.
Page 151 of 276
7/
CHECKS
CHECKING LEVELS
Check all of these levels regularly and top them up if necessary, unless
otherwise indicated.
If a level drops signifi cantly, have the corresponding system checked by
a PEUGEOT dealer or a qualifi ed workshop.
OIL LEVEL
The check is carried out either when the ignition is switched
on using the oil level indicator on the instrument panel, or
using the dipstick.
This manual check will only be correct if the vehicle is on level ground
and the engine has been off for more than 30 minutes.
After topping up the oil, the check when switching on the ignition
with the oil level indicator in the instrument panel will only be valid
30 minutes after topping up.
It is normal to top up the oil level between services. PEUGEOT
recommends that you check the oil level and top up if necessary
every 3 000 miles (5 000 kilometres).
Engine oil change
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited.
BRAKE FLUID LEVEL
The brake fl uid level should be close to the "MAX" mark. If it is
not, check the brake pad wear.
Changing the fluid
Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
Fluid specification
The brake fl uid must conform to the manufacturer's recommendations
and meet the DOT4 standard.
POWER STEERING FLUID LEVEL
The power steering fl uid level should be close to the "MAX"
mark. Unscrew the cap, with the engine cold, to check the level.
When working under the bonnet, take care, as certain areas of the
engine may be extremely hot (risk of burns).
Oil specification
The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.
Page 153 of 276
7/
CHECKS
CHECKS
Unless otherwise indicated, check these components in accordance with
the Warranty and Maintenance Record and according to your engine.
Otherwise, have them checked by a PEUGEOT dealer or a qualifi ed
workshop.
BATTERY
AIR FILTER AND PASSENGER COMPARTMENT FILTER
OIL FILTER
PARTICLE EMISSION FILTER (DIESEL)
On a new vehicle, the fi rst particle fi lter regeneration operations
may be accompanied by a "burning" smell, which is perfectly
normal.
Following prolonged operation of the vehicle at very low speed or
at idle, you may, in exceptional circumstances, notice the emission
of water vapour at the exhaust on acceleration. This does not
affect the behaviour of the vehicle or the environment.
The battery does not require any maintenance.
However, check that the terminals are clean and correctly
tightened, particularly in summer and winter.
When carrying out work on the battery, refer to the "Practical
information" section for details of the precautions to be taken before
disconnecting the battery and following its reconnection.
Refer to the Warranty and Maintenance Record for details of
the replacement intervals for these components.
Depending on the environment (e.g. dusty atmosphere) and
the use of the vehicle (e.g. city driving), replace them twice
as often if necessary
(refer to the "Engines" section).
A clogged passenger compartment fi lter may have an adverse effect
on the performance of the air conditioning system and generate
undesirable odours. Replace the oil fi lter each time the engine oil is changed.
Refer to the Warranty and Maintenance Record for details of
the replacement interval for this component.
The start of saturation of the particle emissions fi lter is
indicated by the temporary illumination of this warning lamp,
accompanied by an audible signal and a message on the risk
of blockage of the particle emissions fi lter.
As soon as the traffi c conditions permit, regenerate the fi lter by driving
at a speed of at least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the "Additive level" section.