turn signal Peugeot RCZ 2011 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2011, Model line: RCZ, Model: Peugeot RCZ 2011Pages: 276, PDF Size: 51.24 MB
Page 32 of 276
30
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the
corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, illumination of the
indicator lamp may also be accompanied by:
- a pictogramme in the central instrument panel screen and a
message in the multifunction screen,
or
- a pictogramme and a message in the central instrument panel
screen.
Warning lamp
is on
Cause
Action/Observations
Left-hand
direction
indicato
r
fl ashing with
buzzer. The lighting stalk is pushed
down.
Right-hand
direction indicator
fl ashing with
buzzer. The lighting stalk is pushed up.
Hazard warning
lamps
fl ashing with
audible signal. The hazard warning lamps
switch, located on the dashboard,
has been operated. The left-hand and right-hand direction indicators and their
associated indicator lamps fl ash simultaneously.
Sidelamps
fi xed. The lighting stalk is in the
"Sidelamps" position or the
"AUTO" position with low light.
Dipped beam
headlamps
fi xed.
The lighting stalk is in the "Dipped beam
headlamps" position or in the "AUTO"
position in conditions of low light.
Main beam
headlamps
fi xed. The lighting stalk is pulled
towards you. Pull the stalk again to return to dipped beam headlamps.
Page 35 of 276
1/
5090
130
INSTRUMENTS AND CONTROLS
COOLANT TEMPERATURE INDICATOR
With the engine running, when the needle is:
- in zone A
, the temperature is correct,
- in zone B
, the temperature is too high; the maximum temperature
warning lamp and the central STOP
warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.
You MUST stop as soon as it is safe to do so.
Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualifi ed workshop.
ENGINE OIL LEVEL INDICATOR
This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The vehicle must be on level ground and the engine must have
been off for more than 30 minutes for this level check to be
accurate. After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:
)
wait for the engine to cool,
)
unscrew the cap by two turns to allow the pressure to drop,
)
when the pressure has dropped, remove the cap,
)
top up the level to the "MAX" mark.
offkm/h90
OIL OKOil level
correct
Page 54 of 276
52
Folding the key
)
First press this button to fold the key.
LOCATING YOUR VEHICLE
REMOTE CONTROL PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction,
you can no longer unlock, lock or locate your vehicle.
)
First of all, use the key in the lock to unlock or lock your vehicle.
)
Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as
possible.
Reinitialisation
)
Switch off the ignition.
)
Turn the key to position 2 (Ignition on)
.
)
Press the closed padlock immediately for a few seconds.
)
Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620/3 volts.
If the battery is fl at, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
)
Unclip the casing using a coin at the notch.
)
Slide the fl at battery out of its location.
)
Slide the new battery into its location observing the original
direction.
)
Clip the casing.
)
Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light. Your vehicle must be
locked.
)
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will
fl ash for a few seconds.
Page 92 of 276
90
C.
Foglamp selection ring.
The foglamps operate with the dipped and main beam headlamps.
Front and rear foglamps.
Press, turning ring C
:
)
forwards once to switch on the front foglamps,
)
forwards again to switch on the rear foglamp,
)
rearwards once to switch off the rear foglamp,
)
rearwards again to switch off the front foglamps.
When the lighting is switched off automatically (with AUTO model) or
when the dipped beam headlamps are switched off manually, the front
foglamps and the sidelamps will remain on.
)
Turn the ring rearwards to switch off the front foglamps,
the sidelamps will then switch off.
In good or rainy weather, both day and night, the front foglamps
and the rear foglamp are prohibited. In these situations, the power
of their beams may dazzle other drivers. They should only be
used in fog or snow.
In these weather conditions, it is your responsibility to switch
on the foglamps and dipped beam headlamps manually as the
sunshine sensor may detect suffi cient light.
Do not forget to switch off the front foglamps and the rear foglamp
when they are no longer necessary.
Switching off of the lamps when the ignition is switched off
On switching off the ignition, all of the lamps turn off immediately,
except for dipped beam if guide-me-home lighting is activated.
Switching on the lamps after the ignition is switched off
To reactivate the lighting control, rotate ring A
to the "0"
position -
lamps off, then to the desired position.
On opening the driver's door a temporary audible signal warns the
driver that the lighting is on.
The lamps, with the exception of the sidelamps, switch off
automatically after a maximum duration of thirty minutes to
prevent discharging of the battery.
Page 94 of 276
92
AUTOMATIC ILLUMINATION OF HEADLAMPS
The sidelamps and dipped beam headlamps are switched on automatically,
without any action on the part of the driver, when a low level of external light is
detected or in certain cases of activation of the windscreen wipers.
As soon as the brightness returns to a suffi cient level or after the windscreen
wipers are switched off, the lamps are switched off automatically.
Activation
)
Turn the ring to the "AUTO"
position. The automatic illumination of
headlamps is accompanied by a message in the screen.
Deactivation
)
Turn the ring to another position. Deactivation is accompanied by a
message in the screen.
Associated with the automatic "Guide-me-home" lighting
Association with the automatic lighting provides the "guide-me-home"
lighting with the following additional options:
- selection of the lighting duration of 15, 30 or 60 seconds in the
vehicle parameters in the vehicle confi guration menu,
- automatic activation of "guide-me-home" lighting when automatic
lillumination of headlamps is in operation.
Operating fault
In the event of a malfunction of the sunshine sensor, the
lighting comes on, this warning lamp is displayed in the
instrument panel and/or a message appears in the screen,
accompanied by an audible signal.
Contact a PEUGEOT dealer or a qualifi ed workshop.
In fog or snow, the sunshine sensor may detect suffi cient light. In
this case, the lighting will not come on automatically.
Do not cover the sunshine sensor, coupled with the rain sensor
and located in the centre of the windscreen behind the rear view
mirror; the associated functions would no longer be controlled.
Page 109 of 276
5/
SAFETY
Before operating the spoiler, ensure that no one is in the proximity
of the moving parts to avoid any risk of injury.
Nevertheless, in the event of pinching, you must reverse the
movement of the spoiler. To do this, release the control button
then press it again to raise the spoiler.
MAINTENANCE
To maintain the spoiler, with the vehicle stationary, ignition on:
)
raise the spoiler to the maximum position B
by pressing the button
briefl y,
)
once the cleaning is complete, retract the spoiler: press and hold
the button until the end of the manoeuvre.
The keep this system in good working order, check the spoiler and its
housing periodically preventing the unwanted accumulation of leaves,
ice or snow.
OPERATING FAULT
If the control system fails, the indicator lamp in the control button
fl ashes, accompanied by an audible signal and a message in the
screen. As a safety precaution, the spoiler rises to the maximum
position, regardless of the speed of the vehicle.
If the problem persists and you wish to retract the spoiler:
)
stop where it is safe to do so,
)
switch off the ignition,
)
switch the ignition on again.
If the indicator lamp no longer fl ashes, the failure was temporary, the
system has resumed normal operation. To retract the spoiler, refer to
the paragraph "To exit from manual mode".
If the indicator lamp fl ashes again and the spoiler is still raised, the
system is still faulty.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
In the event of a system operating fault (e.g. jamming of the spoiler), the
indicator lamp in the control button fl ashes, accompanied by an audible
signal and a message in the screen. For safety reasons, do not exceed
a speed of 85 mph (140 km/h).
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
Before washing the vehicle, always retract the spoiler into its
housing.
Keep the end of the high-pressure nozzle at least 1 metre from the
spoiler housing.
Never press on the spoiler to close the boot or push the vehicle as
this may damage it.
The installation of load-carrying accessories on the vehicle limits
the effectiveness of the spoiler.
Do not install load carrying accessories which are not
recommended by PEUGEOT.
To exit from manual mode:
)
press the button briefl y: the indicator lamp on the button goes off
(return to automatic mode).
At speeds below 6 mph (10 km/h), the spoiler stays in the open
position. It retracts automatically as soon as the vehicle exceeds
this speed threshold.
Page 126 of 276
124
IGNITION SWITCH
ELECTRONIC ENGINE IMMOBILISER
STARTING THE VEHICLE
)
Insert the key in the ignition switch.
The system recognises the starting code.
)
Turn the key fully towards the dashboard to position 3 (Starting)
.
)
When the engine starts, release the key.
SWITCHING THE VEHICLE OFF
)
Immobilise the vehicle.
)
Turn the key fully towards you to position 1 (Stop)
.
)
Remove the key from the ignition switch.
Key left in the "Ignition on" position
If the key has been left in the ignition switch, the ignition will be
switched off automatically after one hour.
To switch the ignition back on, turn the key to position 1 (Stop)
,
then back to position 2 (Ignition
on
)
.
The key contains an electronic chip which has a special code. When
the ignition is switched on, this code must be recognised in order for
starting to be possible.
A few minutes after the ignition is switched off, this electronic engine
immobiliser locks the engine management system and prevents starting
of the engine by anyone who does not have the key.
In the event of a malfunction, you are informed by lighting of this
warning lamp, an audible signal and a message on the screen.
In this case, your vehicle does not start; contact a PEUGEOT
dealer as soon as possible.
Page 132 of 276
3
3
130
DISPLAYS IN THE INSTRUMENT PANEL
When you move the lever in the gate to select a position, the
corresponding indicator lamp is displayed in the instrument panel.
P.
Park
R.
Reverse
N.
Neutral
D1... D6.
Drive (Automatic driving)
S.
Sport
programme
7
. Snow
programme
M1... M6.
Manual (Sequential driving)
-.
Invalid value during manual operation
MOVING OFF
)
Apply the parking brake.
)
Select position P
or N
.
)
Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.
)
With the engine running, press the brake pedal.
)
Release the parking brake.
)
Select position R
, D
or M
,
)
Gradually release the brake pedal.
The vehicle moves off immediately.
If position N
is engaged inadvertently while driving, allow the
engine to return to idle then engage position D
to accelerate.
When the engine is running at idle, with the brakes released,
if position R
, D
or M
is selected, the vehicle moves even without
the accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P
.
A message appears if you try to move the gear lever from
position P
to another position without pressing the brake pedal.
Page 134 of 276
132
It is only possible to change from one gear to another if the vehicle
speed and engine speed permit; otherwise, the gearbox will operate
temporarily in automatic mode.
M
and the gears engaged manually appear in succession in
the instrument panel.
If the engine speed is too low or too high, the gear selected
fl ashes for a few seconds, then the actual gear engaged is
displayed.
It is possible to change from position D
(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox
selects gear M1
automatically.
The sport and snow programmes do not operate in manual mode.
Invalid value during manual operation
This symbol is displayed if a gear is not engaged correctly
(selector between two positions).
STOPPING THE VEHICLE
Before switching off the engine, you can engage position P
or N
to
place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle. If the lever is not in position P
, when the driver's door is opened or
approximately 45 seconds after the ignition is switched off, there is
an audible signal is heard accompanied by a message.
)
Return the lever to position P
; the audible signal stops and the
message disappears.
OPERATING FAULT
When the ignition is on, the illumination of this warning lamp,
accompanied by an audible signal and a message in the
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to emergency mode and is locked in
3rd gear. You may feel a substantial knock when changing from P
to R
and from N
to R
. This will not cause any damage to the gearbox.
Do not exceed a speed of 60 mph (100 km/h), local speed restrictions
permitting.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
This warning lamp may also come on if a door is opened.
There is a risk of damage to the gearbox:
- if you press the accelerator and brake pedals at the same
time,
- if you force the lever from position P
to another position when
the battery is fl at.
To reduce fuel consumption during a long period stationary with
the engine running (traffi c jam, etc.), place the gear lever in
position N
and apply the parking brake.
Page 145 of 276
7/
ESSENCE SANS PLOMB
UNLEADED FUEL ONLY
NUR BLEIFREI BENZIN
GASOLINA SIN PLOMO
RON 95/98
CHECKS
FUEL TANK
Fuel tank capacity: approximately 55 litres.
LOW FUEL LEVEL
FILLING
When the fuel tank minimum level is reached this warning
lamp comes on on the instrument panel, accompanied by an
audible signal and an alert message. When it fi rst comes on
there remains approximately 5 litres
of fuel in the tank.
Until suffi cient fuel is added, this warning lamp appears every time
the ignition is switched on, accompanied by an audible signal and a
message. When driving, this audible signal and display of the alert
message are repeated with increasing frequency as the fuel level drops
towards "0"
.
Refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (Diesel), refer also to the "Running out of fuel
(Diesel)" section.
A label affi xed to the inside of the fl ap reminds you of the type of fuel to
be used depending on your engine.
Additions of fuel must be of at least 5 litres, in order to be taken into
account by the fuel gauge. To fi ll the tank in complete safety:
)
the engine must be switched off,
)
press the rear part of the fl ap, then raise it to open it,
)
turn the cap to the left,
)
remove the cap and hook it onto the clip located on the inside of the
fl ap,
)
fi ll the tank, but do not continue after the 3rd cut-off of the
pump
; this could cause malfunctions. Opening the fi ller cap may create a noise a caused by an inrush
of air. This vacuum is entirely normal, resulting from the sealing of
the fuel system.