lock PONTIAC FIREBIRD 1994 Owner's Manual

Parking Lots: If you park in a lot where
someone will be watching your vehicle,
it's best to lock it up and take your keys.
But what if you have to leave your
ignition key? What if you have to leave
something valuable in your vehicle?
Put your valuables in a storage area,
like your glove
box.
0 Lock the glove box.
0 Lock all the doors except the driver's.
Then take the door key with you.
I
GM -
I PASS-Key@IZ
four vehicle is equipped with the
-'ASS-Key@II (Personalized Automotive
iecurity System) theft-deterrent system.
-'ASS-Key@II is a passive theft-deterrent
iystem.
This means you don't have to do
mything different to
arm or disarm the
iystem. It works when you insert or
'emove the key from the ignition.
-'ASS-Key@II uses a resistor pellet in
he ignition key that matches a decoder
n your vehicle. When
the PASS-Key@II system senses
that someone is using the wrong key, it
shuts down the vehicle's starter and fuel
systems. For about three minutes, the
starter won't work and fuel won't
go to
the engine. If someone tries to start your
vehicle again or uses another key -during
this time, the vehicle will not start. This
discourages someone from randomly
trying different keys with different
resistor pellets in an attempt to make a
match.
. ..,.
49 . 8
ProCarManuals.com

Features and Controls
I rl SECUIITY
The ignition key must be clean and dry
before it’s inserted in the ignition or the
engine may not start. If the engine does
not start and the “SECURITY” light stays on when you
try to start the vehicle, the
key may be dirty or wet. Turn the
ignition
off.
Clean and dry the key. Wait about three
minutes and try again. The security light
will remain on during this time. If the
starter still won’t work, and the key
appears to be clean and
dry, wait about
three minutes and try another ignition key.
At this time, you may also want
to check
the fuses (see “Fuses and Circuit
Breakers” in the Index). If the starter
won’t work with the other key, your
vehicle needs service.
If your vehicle
does start, the first ignition key may be
... 50
Faulty. See your Pontiac dealer or a
locksmith who can service the
PASS-Key@II.
[f you accidentally use a key that has a
Jamaged or missing resistor pellet, the
starter won’t work and the security light
will flash. But you don’t have to wait
three minutes before trying another
ignition key.
See your Pontiac dealer or a locksmith
who can service the PASS-Key@II to
have a new key made.
If you’re ever driving and the
“SECURITY’’ light comes on and stays
on, you will be able to restart your engine
if you turn it
off. Your PASS-Key@ I1
system, however, is not working properly
and must be serviced by your Pontiac
dealer. Your vehicle is not protected by
the PASS-Key% system.
If you lose or damage a PASS-Key@ I1
ignition key, see your Pontiac
dealer or a locksmith who can service
PASS-Key% to have a new key made.
In
an emergency, call the Pontiac Roadside
Assistance Program on
1-800-ROADSIDE
or 1-800-762-3743.
New Vehicle
“Break-Zn”
NOTICE:
Your modem Pontiac doesn’t need an
elaborate “break-in.” But it will per-
form better in the long run if you fol-
low these guidelines:
Keep your speed at
55 mph (88
km/h) or less for the first 500
miles (804 km).
Don’t drive at any one speed
-
fast or slow - for the first 500
miles (804 km). Don’t make
full-throttle starts.
Avoid malung hard stops for the
first 200 miles (322 km) or
so.
During this time your new brake linings aren’t yet broken in. Hard
stops with new linings can mean
premature wear and earlier
replacement. Follow this
“brealung-in” guideline every
time you get new brake linings.
ProCarManuals.com

D
Ignition Switch
With the ignition key in the ignition
switch, you can
turn the switch to five
positions:
Acc (A): Position in which you can
operate your electrical power accessories.
Press in the ignition switch as you
turn
the top of it toward you.
LOCK (B): The only position in which
you can remove the key. This locks your
steering wheel, ignition and automatic
transmission.
If you have an automatic transmission,
tht
ignition switch can’t be turned to
“LOCK’ unless the shift lever is in the
“P’ (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories. Use this position if your
vehicle must be pushed or towed. A
warning tone will sound if you open the
driver’s door when the ignition is in
“Off”
and the key is in the ignition.
Run (D): Position to which the switch
returns after you start your engine and
release the switch. The switch stays in the
“Run” position when the engine is
running. But even when the engine is not
running, you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “Acc” and “Run” allow you to
operate your electrical accessories, such
as the radio and ventilation fan.
:I
Ley Release Button: If you have a
lanual transmission, your ignition lock
as a key release button.
You must press
le button before you can take your key
ut of the ignition lock.
51 . .
ProCarManuals.com

Features and Controls
If your key seems stuck in “Lock”
and you can’t turn it, be sure it is all
the way in. If
it is, then turn the steer-
ing wheel left and right while you
turn the key hard. But turn the key
only with your hand. Using a tool to
force it could break the key or the
ignition switch.
If none of this works,
then your vehicle needs service.
Retained Accessory Power (RAP)
[f you have power door locks, your
vehicle has a feature called Retained
Accessory Power (RAP). With
RAP your
power door locks, electric mirrors, power
windows, audio system and remote hatch
release will continue to work up to 10
minutes after the ignition key is turned to
“OW’ and neither door is opened.
[f a door is opened, the audio system and
power windows will shut
off. The power
door locks, electric mirrors and remote
hatch release will work until you shut the
door. Once you have shut the door, these
accessories will continue to work for
approximately
35 seconds. After this
time you will not be able to use these
accessories until the next time you open
a door or turn on the ignition.
Starting Your Engine
Automatic Transmission: Move your
shift lever to
“P” (Park) or “N’ (Neutral).
Your engine won’t start in any other
position
- that’s a safety feature. To
restart when you’re already moving,
use
“N’ (Neutral) only.
NOTICE:
Don’t try to shift to “P” (Park) if
your Pontiac is moving. If you do,
you could damage the transmission.
Shift to
“P” (Park) only when your
vehicle is stopped.
Manual Transmission: The gear select01
should be in neutral. Hold the clutch
pede1 to the floor and start the engine.
Your vehicle won’t start if the clutch
pedal is not all the way down
- that’s
a safety feature.
To start your V6 engine:
1. Without pushing the accelerator pedal
turn your ignition key to “Start.”
When the engine starts, let go of the
key. The idle speed will go down as
your engine gets warm.
... 52
ProCarManuals.com

C L
S
c
V
S
b
tc
V
P
n
U
C
S
F
tl
TRANSMISSION
INDEEAR@ START
Fecond-Gear Start
‘our vehicle may be equipped with a
econd-Gear Start feature. Press
“2ND
;EAR START” to provide more traction
vhen you are starting on ice or other
lippery surfaces. The transmission will
le in second gear when the vehicle begin;
3 move. After starting in second gear, tht
rehicle will upshift normally.
’his feature
is only for improved traction
then the road surface is slippery and is
lot intended for continuous use. Always
.se “NORMAL” for normal road
onditions.
You may press “2ND GEAR
;TART’’ again to turn off this feature.
Yhenever you start your vehicle, the
ransmission is in the “NORMAL” mode.
Engine Coolant Heater (Engine
Block Heater)
(OPTION)
In very cold weather, 0°F (- 18 “C) or
colder,
the engine coolant heater can help.
You’ll get easier starting and better fuel
economy during engine warm-up.
Usually, the coolant heater should be
plugged in a minimum of four hours prior
to starting your vehicle.
To use the coolant heater:
1. Turn off the engine.
2. Open the hood and unwrap the
electrical cord.
3. Plug it into a normal, grounded 110-volt outlet.
NOTICE:
After you’ve used the coolant heater,
be sure to store the cord
as it was
before to keep it away from moving
engine parts. If
you don’t, it could be
damaged.
55.
ProCarManuals.com

Features and Controls
How long should you keep the coolant
heater plugged in? The answer depends
on the weather, the kind
of oil you have,
and some other things. Instead
of trying to
list everything here, we ask that you
contact a Pontiac dealer in the area where
you’ll be parking your vehicle. The dealer
can give you the best advice for that
particular area.
Autamatic Transmission
There are several different positions for
your shift lever.
P (Park)
This locks your rear wheels. It’s the best
position to use when you start your
engine because your vehicle can’t move
easily.
... 56
ProCarManuals.com

Ensure the shift lever is fully in “P”
(Park) range before starting the engine.
Your Pontiac has a brake-transmission
shift interlock. You have to fully apply
your regular brakes before you can shift
from
“P” (Park) when the ignition key is
in the “Run” position. If you cannot shift
out of
“P’ (Park), ease pressure on the
shift lever
- push the shift lever all the
way into “P” (Park) and also release the
shift lever button on floor shift console
models as you maintain brake application.
Then move the shift lever into the gear
you wish. (Press the shift lever button
before moving the shift lever on floor
shift console models.) See “Shifting out
of
“P” (Park)” in this part.
R (Reverse)
Use this gear to back up.
NOTICE:
Shifting to “R” (Reverse) while your
vehicle is moving forward could
damage your transmission. Shift to
“R’ only after your vehicle is
stopped.
To rock your vehicle back and forth to
get out of snow, ice or sand without
jamaging your transmission, see “Stuck:
[n Sand, Mud, Ice or Snow, If You’re”
In the Index.
@ N (Neutral)
[n this position, your engine doesn’t
:onnect with the wheels.
To restart when
You’re already moving, use
“N” (Neutral)
mly. Also, use
“N’ when your vehicle is
Jeing towed.
NOTICE:
Damage to your transmission caused
by shifting out of
“P” (Park) or “N”
(Neutral) with the engine racing isn’t
covered by your warranty.
57 ...
ProCarManuals.com

Your six-speed manual transmission
has a feature that allows you to safely
shift into
“R’ (Reverse) while the vehicle
is rolling (at less than 3 mph). You will be
“locked-out” if you try to shift into “R”
(Reverse) while your vehicle is’ moving
faster than
3 mph.
If you have turned your ignition off and
wish to park your vehicle in Reverse, you
will have to move the shift lever quickly
to the right, “crashing” through the high
load spring and then into gear.
SKIP
SHIFT
;kip Shift Light (5.7L LT1 Engine)
Yhen this light comes on, you can only
hift from
“1” (First) to “4” (Fourth) gear
nstead of “1” (First) to “2” (Second)
gar. This helps you to get
the best
lossible fuel economy.
’his light will come on under these
onditions:
The engine coolant temperature is greater than 170°F (77”C),
You are going
15-20 mph
(24-32
km/h), and
You are
at 35% throttle or less. When this
light
is on, the gear shift lever
will let you shift from
“1” (First) gear to
“4”(Fourth) gears only. Once you are
in
“4” (Fourth) gear, you can press the
clutch again and shift into another gear.
Follow the shift speeds in this chart when
the
“SKIP SHIFT” light is on.
Computer Aided Manual Transmission
Shift Speeds:
1st to 4th. . , . , . . 15 mph (24 km/h)
4th to 5th ...... 25 mph (40 km/h)*
5th
to 6th ...... 40 mph (64 km/h)**
Each time you come to
a stop, the
engine’s Electronic Control Module
(EGM) determines when to activate the
“SKIP SHIFT” upshift system. Use
“2”
(Second) gear only when you accelerate
very quickly from’a stop.
You can then
follow the full gear shift pattern.
*30 mph (48 km/h) when accelerating
to highway speeds.
**45 mph (72 km/h) when accelerating
to highway
speeds.
61 ’. , . ProCarManuals.com

Features and Controls
Shifting into P (Park)
(AUTOMATIC TRANSMISSION)
1. Hold the brake pedal down with your
right foot and set the parking brake.
2. Move the shift lever into T“ (Park)
position like this:
Hold in the button on the lever,
and push the lever all the way
toward the front of your vehicle.
3. Move the ignition key to “LOCK.”
4. Remove the key and take it with you.
If you can walk away from your
vehicle with the ignition key in your
hand, your vehicle is in
“P’ (Park).
Leaving Your Vehicle with the
Engine Running
(AUTOMATIC TRANSMISSION)
If you have to leave your vehicle with the
engine running, be sure your vehicle is
in
“P’ (Park) and your parking brake is
firmly set before you leave it. After
you’ve moved the shift lever into the
“P’
(Park) position, hold the regular brake
pedal down. Then, see if you can move
the shift lever away from
“P’ (Park)
without first pushing the button. If you
can, it means that the shift lever wasn’t
fully locked into
“P” (Park).
... 64
ProCarManuals.com

Torque Lock
(AUTOMATIC TRANSMISSION)
If you are parking on a hill and you don’t
shift your transmission into “P” (Park)
properly, the weight of the vehicle may
put too much force on the parking pawl in
the transmission. You may find it difficult
to pull the shift lever out of “P” (Park)
This is called “torque lock.” To prevent
torque lock, set the parking brake and
then shift into “P’7 (Park) properly before
you leave the driver’s Seat. To find out
how, see “Shifting Into “P” (Park)” in
the Index.
When you are ready to drive, move the
shift lever out of
“P” (Park) BEFORE you
release the parking brake.
If “torque lock” does occur, you may
need to have another vehicle push yours
a little uphill to take some of the pressure
from the transmission,
so you can pull the
shift lever out of “P” (Park).
Shifting out of P (Park)
(AUTOMATIC TRANSMISSION)
Your Pontiac has a brake-transmission
shift interlock. You have to fully apply
your regular brake before you can shift
from “P” (Park) when the ignition is in
the “Run” position. See “Automatic
Transmission” in the Index.
If you cannot shift out of
“F”’ (Park), ease
pressure on the shift lever
- push the
shift lever all the way into
“P” (Park) and
release the shift lever button as you
maintain brake application. Then press
the shift lever button and move the shift
lever into the gear you wish.
If you ever hold the brake pedal down but
still can’t shift out of
“P” (Park), try this:
1. Turn the key to “Off.”
2. Apply and hold the brake until the end
3. Shift to “N’ (Neutral).
4. Start the vehicle and then shift to the
drive gear you want.
of
Step
4.
5. Have the vehicle fixed as soon as you
can.
Parking Your Vehicle
(MANUAL TRANSMISSION)
Before you get out of your vehicle, put
your manual transmission in
“R’
(Reverse) and firmly apply the parking
brake.
If your vehicle is equipped
to tow a
trailer, see “Towing a Trailer” in the
Index.
65..
ProCarManuals.com