fuel PONTIAC FIREBIRD 1996 User Guide

If the Light Is Flashing
The following may prevent more serious damage to
your s&ide:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If towing a trailer, reduce the amount of cargo being
hauled
as soon as it is possible.
If the light stops flashing and remains on steady, see “If
the Light Is On Steady” following.
If the light continues to flash, whenit is safe to do so, ’
stop the vehicle. Put your vehicle in PARK (P). Turn the
key
off, wait at least 10 seconds and restart the engine.
If the light remains on steady, see “If the Light Is On
Steady” following.
If the light is still flashing follow the
previous steps, and drive the vehicle to your dealer or
*qualified service center for service.
If the Light Is On Steaay
You may be able to correct the emission system
malfunction by considering
the following:
Did you just put
fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully install
the cap. The diagnostic system can determine if the fuel
cap has been left
off or improperly installed. This will
dow fuel to evaporate into the atmosphere. A few
driving trips
should turn the light off.
Did you just drive through a deep puddle of water?
If so, your el’ectrical system may be wet. The condition
will usually
be corrected when the electrical system
dries
out. A few driving trips should turn the light off.
Are you low on fuel?
As your engine
starts to run out of fuel, your engine may
not bun as efficiently as designed since small amounts of
air are sucked into the fuel line causing a misfire. The
system can detect this. Adding fuel should correct this
condition. Make sure to install the fuel cap properly. It
will take a few driving trips to turn the light off.
ProCarManuals.com

Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel (see
“Fuel” in the Index).
Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditijons may go away once the engine is warmed up.)
This will be detected by the system and cause
the light
to turn on.
If you experience this condition, change the fuel brand
you use. It will require at least one full tank of the
proper fuel to turn the light
off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has
the proper test equipment and
diagnostic tools
to fix any mechanical or electrical
problems that may have developed.
Engine Oil Pressure Gage
This gage tells you if there
could be
a problem with
your engine oil pressure.
The engine oil pressure gage shows the engine oil
pressure in psi (pounds per square inch) in the United
States, or Wa (kilopascals)
in Canada, when the engine
is running. Oil pressure should be 20 to 80 psi (140 to
550 kPa). On the 3800 engine the oil pressure should be
between
20 and 120 psi (140 to 827 kPa). It may vary
with engine speed, outside temperature and oil viscosity,
but readings above the red area show the normal
operating range. Readings in the red area tell
you that
the engine is low on oil, or that you might have some
other oil problem. See “Engine Oil” in the Index.
2-85
ProCarManuals.com

NOTICE:
The oil level monitoring system only checks the oil level when you are starting your engine. It does not
keep monitoring the level once your
engine is running.
Also, the oil level check only
works when the engine has been turned
off long
enough for the oil to drain back into the oil pan.
Check Gages Light
CHECK GAGES
This warning light will
come on briefly when you
are starting the engine. If
the light comes on and stays
on while you are driving,
check your gages to see if
they are
in the warning
areas.
Fuel Gage
Your fuel gage shows about
how much fuel is in your
tank. The gage works only
when the ignition switch is
in the RUN position.
I I
When the gage pointer first indicates EMPTY (E), you
still have a little fuel left (about one to two gallons), but
you need
to get more right away.
Here are four concerns some owners have had about the
fuel gage. All these situations are normal and do not
indicate that anything is wrong with the fuel gage.
At the gas station, the gas pump shuts off before the
It takes more (or less) gas to fill up than the gage
gage
reads
FULL (F).
reads. For example, the gage reads half full, but it took
more (or less) than half of the tank’s capacity to fill it.
a The gage moves a little when you turn, stop or speed up.
When you turn the engine off, the gage doesn’t go
back to EMPTY (E).
2-87
ProCarManuals.com

The air conditioner compressor operates in MAX, A/C,
BI-LEVEL, BLEND and DEFROST when the outside
temperature is above freezing. When the air conditioner
is on, you may sometimes notice slight changes
in your
vehicle’s engine speed and power. This is normal because
the system .is designed to cycle the compressor on and off
to keep
the desired cooling and help fuel economy.
Cooling
The air conditioner works best if you keep your
windows closed.
On very hot days, open the windows
just long enough for the hot air to escape.
1. Turn the air control knob to A/C for normal cooling.
2. Turn the temperature control knob to a
3. Move the fan control knob to the desired speed. For faster cooling, move
the knob to
MAX.
comfortable setting. During initial start-up
only, if your vehicle
is equipped
with an optional engine coolant heater, you can use it in
cold weather (around
+20 O F/-8 O C or lower) to improve
heater performance on start up. Because an engine
coolant heater warms the engine coolant, your vehicle’s
‘heating system can more efficiently provide heat for the
passenger area
of your vehicle. See “Engine Coolant
Heater” in the Index.
Bi-Level Heating
You may want to use bi-level heating on cool, but sunny
days. This setting directs cool air toward your body and
warmer air toward your feet.
1. Turn the air control knob to BI-LEVEL.
2. Turn the temperature control knob to a
comfortable setting.
3. Turn the fan control knob to the desired speed.
Heating
The heater works best if you keep your windows closed
while using it.
1. Turn the air control knob to HEATER.
2. Turn the fan control knob to the desired speed.
3. Turn the temperature control knob to a
comfortable setting.
3-3
ProCarManuals.com

. 'The exit speed is usually posted.
, . :Reduce your speed according to your speedometer, not
- : .' :to your sense of motion. After driving for any distance
at higher speeds, you may tend to think you. are going
slower than you actually are.
.pg I*:., :.'-L. :.& .-.(,-.r
Be€ore Leaving on a Long nip'* A
Make sure you're ready. Try to be well rested. If you
must start when you're not fresh -- such 'as after a day's
, work -- don't plan to make too many miles that first part
of the journey. Wear comfortable clothing and shoes you
can easily drive in.
Is your vehicle ready for a long trip?' If you keep it
serviced
md maintained, it's ready to go. If it needs L
service, have it done before starting out. Of course,
you'll find experienced and able service experts in
Pontiac dealerships all across
North America. They'll be
ready and willing to help if you need it.
,' <:. 8
Here are some things you can check before a trip:
Windshield Washer Fluid: Is the reservoir full? Are
all windows clean inside and outside?
Wiper Blades: Are they in goo,d shape?
Fuel, Engine Oil, Other Fluids: Have you checked
all levels?
Lamps: Are they all working? Are the lenses clean?
Tires: They are vitally important to a safe,
trouble-free
trip. Is the tread good enough for
long-distance driving?
Are the tires all inflated to the
recommended pressure?
Weather Forecasts: What's the weather outlook
along your route? Should .you delay your trip a short
time to avoid a major storm system?
Maps: Do you have up-to-date maps?
4-22
ProCarManuals.com

Run your engine only as long as you must. This saves
fuel. When you run the engine, make it go a little faster
than just idle. That
is, push the accelerator slightly. This
uses less fuel for the heat that you get and it keeps the
battery charged. You will need a well-charged battery to
restart the vehicle, and possibly for signaling later on with your headlamps. Let the heater
run for awhile.
Then, shut the engine
off and close the window almost
all the way to preserve the heat. Start the engine again
and repeat this only when you feel really uncomfortable
from the cold. But do it as little as possible. Preserve the
fuel as long as you can. To help keep warm, you can get
out of the vehicle and do some fairly vigorous exercises
every half hour or
so until help comes.
Loading Your Vehicle
'@I OCCUPANTS VEHICLE CAP. WT.
TIRE-LOADING INFORMATION
FRT. CTR.
RR. TOTAL LBS. KG
MAX. LOADING & GVWR SAME AS VEHICLE
CAPACITY
WEIGHT XXX COLD TIRE
TIRE SIZE SPEED PRESSURE
RTG PSI/KPa
FRT.
RR.
SPA.
IF TIRES ARE HOT, ADD 4PS1/28KPa
SEE OWNER'S MANUAL FOR ADDITIONAL
( INFORMATION
Two labels on your vehicle show how much weight it
may properly carry. The Tire-Loading Information label
found on the driver's door tells you the proper size,
speed rating and recommended inflation pressures for
the tires on your vehicle.
It also gives you important
information about the number of people that can be in
your vehicle and the total weight
that you can carry.
This weight is called the vehicle capacity weight and
includes
the weight of all occupants, cargo and aLI
nonfactory-installed options.
ProCarManuals.com

MFD BY GENERAL MOTORS CORP
DATE GYWR GAWR FRT GAWR RR
THIS VE~HICCE CONFORMS TO ALL APPLI-
CABLE U.S. FEDERAL MOTOR VEHICLE .
SAFETY, BUMPER, AND THEFT PREVENTION
STANDARDS
IN EFFECT ON THE DATE OF
MANUFACTURE SHOWN ABOVE.
The other label is the Certification label, found on the
rear edge of the driver's
door. It tells you the gross
weight capacity of your vehicle, called GVWR (Gross
Vehicle Weight Rating). The GVWR includes the weight
of the vehicle, all occupants, fuel and cargo. Never
exceed the GVWR for your vehicle,
or the Gross Axle
Weight Rating (GAWR) for either the front or rear axle.
And, if you do a,heavy had, you should spread it out.
Don't
carry more than 100 lbs. (45 kg) in your rear area.
rn
A C UTION:
Do not load your vehicle any heavier than the
GVWR, or either the maximum front or rear
GAWR. If you do, parts on your vehicle can
break, or it can change
the way your vehicle
handles. These could cause
you to lose control.
Also, overloading can shorten the life of
your vehicle.
A
I
If you put things inside your vehicle -- like suitcases,
tools, packages
or anything else -- they will go as fast as
the vehicle
goes. If you have to stop or turn quickly, or
if there is a crash, they'll keep going.
ProCarManuals.com

Your car can tow a trailer if it is equipped with proper
trailer towing equipment.
To identify what the vehicle
trailering capacity
is for your vehicle, you should read
the infrwmakion in “Weight of the Tr~ler” that appears
later in this section. But trailering
is different than* just
driving your vehicle by itself. Trailering means changes
in handling, durability, and fuel economy. Successful,
safe trailering takes correct equipment, and it has
to be
used properly.
That’s the reason for this part. In it are
many
time-tested, important trailering tips and safety rules.
Many of these are important for your safety and that
of
your passengers. So please read this section carehlly
before you pull a trailer.
Load-pulling components such as the engine,
transmission, rear axle, wheel assemblies and tires
are
forced to work harder against the drag of the added
weight. The engine is required
to operate at relatively
higher speeds and under greater loads, generating extra
heat. What’s more, the trailer adds,considerably to wind
resistance, increasing the pulling requirements.
I
_. . , _, -i .. :
If You Do Decide To Pull A Trailer
If you do, here,are some important points:
0
0
0
0
There are many different laws, including speed limit
restrictions, having to do with trailering. Make sure
your rig will
be legal, not only where you live but
also where you’ll be driving.
A good source for this
information can be state or provincial police.
Consider using
a sway control. You can ask a hitch
dealer about sway
controls.
Don’t tow a trailer at all during the first 1,000 miles
(1 600 km) your new vehicle is driven. Your eng-k,
axle or 0ther.part.s could be damaged.
Then, during the first
500 miles (800 km) that you
tow a trailer, don’t drive ov’er 50 mph (80 km/h) and
don’t make starts
at full throttle. This helps your
engine and other parts of your vehicle wear in at the
heavier loads.
Obey speed limit restrictions when towing a trailer.
Don’t drive faster than the maximum posted speed
for trailers (or no more than
55 mph (90 km/h)) to
save wear on your vehicle’s parts.
4-32
ProCarManuals.com

Section 6 I Service and Appearance Care
Here you will find information about the care of your
Pontiac.
This section begins with service and fuel
infomation, and then it shows how to check important
fluid and lubricant levels. There is also technical
information about your vehicle, and a part devoted to its
appearance care.
Doing Your Own Service Work
If you want to do some of your own service work, you’ll
want to get the proper Pontiac Service Manual. It tells
you much more about how to service your Pontiac than
this manual can.
To order the proper service manual, see
“Service and Owner Publications” in the Index.
Service Your vehicle has an air bag system. Before attempting to
Your Pontiac dealer knows your vehicle best and wants do
Your own service Work, see ‘‘Senicing YWr Air
you
to be happy with it. We hope you’ll go to your Bag-Equipped Pontiac” in the Index.
dealer for all Your service meds- you’ll get genuine GM
You should keep a record with all parts receipts and list
parts and GM-trained and supported service people. the mileage and the date of any service work you
We hope you’ll want to keep your GM vehicle all GM. perform. See “Maintenance Record” in
the Index.
Genuine GM parts have one of these marks:
6-1
ProCarManuals.com

L
You can be injured and your vehicle could be
damaged if
you try to do service work on a
vehicle without knowing enough about it.
0 Be sure you have sufficient knowledge,
experience, and the proper replacement
parts and tools before you attempt
any
vehicle maintenance task.
Be me to use the proper nuts, bolts and
other fasteners. “English” and “metric”
fasteners can be easily confused. If
you use
the wrong fasteners, parts can later break
or fall off.
You could be hurt.
Fuel
The 8th digit of your vehicle identification number
(VIN) shows the code letter for your engine. You will
find the
VIN at the top left of your instrument panel.
(See “Vehicle Identification Number” in
the Index.)
If YQU don’t have the 5.7L Code P engine, use regular
unleaded gasoline rated at 87
octane or higher.
If you have the 5.7L Code P engine, use premium
unleaded gasoline rated at 9 1 octane or higher for best
performance.’
You may use middle grade or regular
unleaded gasolines, but your vehicle may not accelerate
as well.
At a minimum, the gasoline you use should meet spe’cifications
ASTM D4814 in the United States and
CGSB 3.5-M93 in Canada. Improved gasoline
specifications have been develope’d
by the American
Automobile Manufacturers Association (AAMA)
for
better vehicle performance and engine protection.
Gasolines meeting the
AAMA specification could
provide improved driveability and emission control
system protection compared to other gasolines.
Be sure the posted octane for premium is at least 91
(at least 89 for middle grade and
87 for regular). If the
octane is less than
87, you may get a heavy knocking
noise when
you drive. If it’s bad enough, it can damage
your engine.
If you’re using fuel rated at the recommended octane or
higher and you still hear heavy knocking, your engine
needs service. But don’t worry
if you hear a.little
pinging noise when you’re accelerating or driving up a
hill. That’s normal, and you don’t have to buy a higher
octane fuel to get rid
of pinging. It’s the heavy, constant
knock that means you have
a problem.
ProCarManuals.com