trailer PONTIAC FIREBIRD 1996 User Guide
[x] Cancel search | Manufacturer: PONTIAC, Model Year: 1996, Model line: FIREBIRD, Model: PONTIAC FIREBIRD 1996Pages: 386, PDF Size: 19.18 MB
Page 195 of 386

Weight of the Trailer T0ngu.e
The tongue load (A) of any trailer is an important
weight to measure because
it affects,the total capacity
weight
of your vehicle. The capacity weight includes the
curb weight of the vehicle, any cargo’ you may carry in
it, and the people who will be riding in the
vehcle. And
if you will tow
a trailer, you must subtract the tongue
load from your vehicle’s capacity weight because your
vehicle will be carrying that weight, too. See “Loading
Your Vehicle” in the Index for more information about
your vehicle’s maximum load capacity.
-
A B
If you’re using a weight-carrying hitch, the trailer
tongue
(A) should weigh 10%. of the total loaded trailer
weight
(B). If you have a weight-distributing hitch, the
trailer tongue (A)-should weigh 12% of the total loaded
trailer weight
(B).
After you’ve loaded your trailer, weigh the trailer and
then the tongue, separately,
to see if the weights are
proper.
If they aren’t, you may be able to get them right
simply by moving some items around in the trailer.
Total Weight on Your Vehicle’s, Tires
Be sure your vehicle’s tires are inflated’to the
recommended pressure for cold tires. You’ll find these
numbers
on the Certification label at the rear edge of the
driver’s door
‘or see “Loading Your Vehicle” in the
Index. Then be sure you don’t
go over the GVW
limit for your vehicle, including the weight of the
trailer tongue.
ProCarManuals.com
Page 196 of 386

Hitches Safety Chains
It’s
important to have the correct hitch equipment.
Crosswinds, large trucks going by and rough roads
are a
€ew reasons why you’ll need the right hitch. Here are
some rules to follow:
I
Will you have to make any holes in the body of your
vehicle when you install a trailer hitch? If you do,
then be sure to seal the holes later when you remove
the’hitch. If you don’t seal them, deadly carbon
monoxide
(CO) from your exhaust can get into your
vehicle (see “Carbon Monoxide” in the Index). Dirt
and water can, too.
The bumpers on your vehicle are not intended for
hitches. Do not attach rental. hitches or other
bumper-type hitches to them. Use only a
frame-mounted hitch that
does not attach to
the bumper.
-.
You should always attach chains between your vehicle
and your trailer. Cross the safety chains under the tongue
of the trailer
so that the tongue will not drop to the road
if it becomes separated from the hitch. Instructions
about safety chains may be provided-by the hitch
manufacturer or by the trailer manufacturer. Follow the
manufacturer”s recommendation for attaching safety
chains and do not attach them to the bumper. Always
leave just enough slack
so you can turn with your rig.
And, never allow safety chains to drag on the ground.
Trailer Brakes
If your trailer weighs more than 1,000 lbs. (450 kg)
loaded, then it needs its own brakes -- and they must be
adequate. Be sure to read and follow the instructions for
the trailer brakes so you’ll be able to install, adjust and
maintain them properly. Because you have anti-lock
brakes, do not try to tap into your vehicle’s brake
system. If you
do, both brake systems won’t work well,
or at all.
ProCarManuals.com
Page 197 of 386

Driving with a m +er
Towing a trailer requires a certain amount of experience.
Before setting out for the
open road, you’ll want to get
to know your rig. Acquaint yourself with the feel of
handling and braking with the added weight of the
trailer. And always keep .in mind that the vehicle you are
driving is now a good deal longer and not nearly as
responsive as your vehicle
is by itself.
Before you start, check the trailer hitch and platform
(and attachments), safety chains, electrical connector,
lamps, tires and mirror adjustment. If the trailer has
electric brakes, start your vehicle
and trailer moving and
then apply the trailer brake controller by hand to be sure
the brakes are working. This lets you check your
electrical connection at the same time.
During your trip, check occasionally to be sure that the
load is secure, and that the lamps
and any trailer brakes
are still working.
FoIlowing Distance
Stay at least twice as far behind the vehicle ahead as you
would when driving your vehicle without a trailer. This
can help you avoid situations that require heavy braking
and sudden turns.
Passing
You’ll need more passing distance up ahead when
you’re towing a trailer. And, because you’re a good deal
longer,
you’ll need to go much farther beyond the
passed vehicle before
you can return to your lane.
Backing Up
Hold the bottom of the steering wheel with one hand.
Then, to move the trailer to the left, just move that hand
to the left. To move the trailer to the right, move your
hand to the right. Always back up slowly and,
if
possible, have someone guide you.
Making Turns
NOTICE:
Making very sharp turns while trailering could
cause the trailer to come
in contact with the
vehicle.
Your vehicle coul’d be damaged. Avoid
making very
sharp turns while trailering.
When you’re turning with a trailer, make wider turns than
normal. Do this so your trailer won’t strike soft shoulders,
curbs, road signs, trees or other objects. Avoid jerky or
sudden maneuvers. Signal well in advance.
4-36
ProCarManuals.com
Page 198 of 386

Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle may need a
different ‘turn signal flasher and/or extra wiring. Check
with your Pontiac dealer.
The arrows
on your instrument panel will flash
whenever you signal a turn or lane change. Properly
hooked up, the trailer lamps will also flash, telling other
drivers you’re about to turn, change lanes or stop.
When towing a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on the trailer
are burned out. Thus, you may think drivers behind you
are seeing your signal when they are not. It’s important
to check occasionally to be sure the trailer bulbs are
still working.
1 ’ Driving On Grades
Reduce speed and shift to a lower gear before you start
down a long or steep downgrade.
If you don’t shift
down, you might have to use your brakes
so much that
they would get hot and no longer work well.
On
a long uphill grade, shift down and reduce your
speed to around
45 mph (70 km/h) to reduce the
possibility
of engine and transmission overheating.
If YOU are towing a trailer and you have an automatic
transmission with Overdrive, you may prefer to drive in
THIRD (D) instead of AUTOMATIC OVERDRIVE (0)
(or, as you need to, a lower gear). Or, if you have a
manual transmission with
FJFTH (5) (or SIXTH (6)) gear
and you are towing a trailer, it’s better not to use FIFTH
(5) (or SIXTH) (6) gear. Just drive in FOURTH (4) (drive
in
FIFTH (5) if you have a six-speed manual transmission)
or,
as you need to, a lower gear.
Parking on Hills
You really should not park your vehicle, with a trailer
attached, on a hill. If something goes wrong, your rig
could start to move. People can be injured, and both
your vehicle and the trailer can be damaged.
But if you ever have to park your rig on a hill, here’s
how to do it:
1. Apply your regular brakes, but don’t shift into
2. Have someone place chocks under the trailer wheels.
3. When the wheel chocks are in place, release the
regular brakes until the chocks absorb the load..
’
4. Reapply the regular brakes, Then apply your parking
brake, and then shift to
PARK (P), or REVERSE (R)
for a manual transmission.
5. Release the regular brakes.
PARK (P) yet, or into gear for a manual transmission.
4-37
ProCarManuals.com
Page 199 of 386

.. ' When You Are Ready to Leave After
Parking on a €Till
' ' 1. Apply your regular brakes and hold the pedal down
while
you:
Start your engine;
Shift into a gear; and
0 Release the parking brake.
2. Let .up on the brake pedal.
3. Drive slowly until the trailer is clear of the chocks.
4. Stop and have someone pick up and store the chocks.
Maintenance When Trailer Towing
Your vehicle will need service more often when you're
pul1ing.a trailer. See
the Maintenance Schedule for more
on this. Things that are especially important in trailer
operation
are automatic: transmission fluid (don't
overfill), engine oil, axle lubricant, belts,
cooling system
and brake adjustment. Each
of these is covered in this
manual, and the Index will heip you find them quickly.
If you're trailering, it's a good idea to review these
sections befcn-e
you start yam trip.
Check;periodically
to see that all hitch nuts and bolts .
are tight.
.. 1
4-38
ProCarManuals.com
Page 213 of 386

If No Ste~ n Is C Jminp From Your Engine
If you get the overheat warning but see or hear no
steam, the problem may not be too serious. Sometimes
the engine can get a little too hot when
you:
Climb a long hill on a hot day.
0 Stop after high-speed driving.
0 Idle for long periods in traffic.
0 Tow a trailer.
If you get the overheat warning with no sign of steam,
try this for, a minute or so:
1. If you have an air conditioner, turn it off.
2. Turn on your heater to full hbt at the highest fan
speed and open the window as necessary.
3. If you’re in a traffic jam, shift to NEUTRAL (N);
otherwise, shift to the highest gear while
driving
-- AUTOMATIC OVERDRIVE (@) or
DRIVE
(D) for automatic transmissions.
If you no longer have the overheat warning, you can
drive.
Just to be safe, drive slower for about 10 minutes.
If the warning doesn’t come back on, you can
drive normally.
If the warning continues, pull over, stop, and park your
vehicle right away.
If there’s still no sign of steam, you can idle the engine
for two or three minutes while you’re parked, to see
if
the warning stops. But then, if you still have the
warning,
turn oflthe engine and get everyone out of the
vehicle
until it cools down.
You may decide not to lift the hood but to get service
help right away.
5-14
ProCarManuals.com
Page 256 of 386

Most trips include extensive idling (such as frequent driving in stop-and-go traffic).
0 Most trips are through dusty areas.
0 You frequently tow a trailer or use a carrier on top of
0 The vehicle is used for delivery service, police, taxi
your
car.
or other commercial application.
Driving under these conditions causes engine oil to
break down sooner.
If any one of these is true for your
vehicle, then you need to change your oil and filter
every
3,000 miles (5 000 km) or 3 months -- whichever
occurs first.
If none of them
is true, change the oil and filter every
7,500 miles (12 500 km) or 12 months -- whichever
occurs first. Driving a vehicle with a fully warmed
engine under highway conditions causes engine oil to
break down slower.
What to Do with Used Oil
Did you know that used engine oil contains certain
elements that may be unhealthy for your skin and could
even cause cancer? Don’t let used oil stay on your skin
for very long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly
throw
away clothing or rags containing used engine oil. (See
the manufacturer’s warnings about the use and disposal
of oil products.)
Used oil can be
a real threat to the environment. If you
change your own oil, be sure to drain all free-flowing oil
from the filter before disposal. Don’t ever dispose of oil
by putting it in
the trash, pouring it on the ground, into
sewers, or into streams or bodies
of water. Instead,
recycle it by taking it to a place that collects used oil. zf
you have a problem properly disposing of your used oil,
ask your dealer, a service station or a local recycling
center for help.
ProCarManuals.com
Page 261 of 386

Automatic Transmission Fluid
When to Check and Change
A good time to check your automatic transmission fluid
level is when the engine oil
is changed.
Change both
the fluid and filter every 15,000 miles
(25 000 km) if the vehicle is mainly driven under one
or more
of these conditions:
In heavy city traffic where the outside temperature
regularly reaches
90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police or delivery service.
If you do not use your vehicle under any of these
con’ditions, change
the fluid and filter every 100,000 miles
(166 000 km).
See “Scheduled Maintenance Services” in the Index.
How to Check
Because this operation can be a little difficult, you
may choose to have this done at your Pontiac dealership
Service Department.
If you do it yourself, be sure to follow all the instructions
here, or you could get a false reading on the dipstick.
NOTICE:
Too much or too little fluid can damage your
transmission. Too much can mean that some of
the fluid could come out and fall on hot engine
parts or exhaust system parts, starting a fire.
Be
sure to get an accurate reading if you check your
transmission fluid.
Wait at least 30 minutes before checking the
transmission fluid level if
you have been driving:
When outside temperatures are above 90°F (32 ” C).
At high speed for quite a while.
0 In heavy traffic -- especially in hot weather.
0 While pulling a trailer.
To get the right reading, the fluid should be at normal
operating temperature, which
is 180°F to 200°F
(82°C to 93°C).
ProCarManuals.com
Page 317 of 386

Maintenance Schedule
Short Trip/City Definition
Follow the Short TripKity Maintenance Schedule if any
one
of these conditions is true for your vehicle:
0 Most trips are less than 5 to 10 miles (8 to 16 km).
This is particularly important when outside
temperatures are below freezing.
0 Most trips include extensive idling (such as frequent
driving in stop-and-go traffic).
$0 Most trips are through dusty areas.
You frequently tow a trailer or use a carrier on top of
0 If the vehicle is used for delivery service, police, taxi
One ofthe reasons you should follow this schedule if you
operate your vehicle under any of these conditions is that
these conditions cause engine oil to break down
soonel:
your vehicle.
or other commercial application.
Short Trip/City Intervals
~~
Every 3,000 Miles .(5 000 km): Engine Oil and Filter
Every 6,000 Miles (10 000 km): Chassis Lubrication
Change
(or 3 months, whichever occurs first).
(or
6 months, whichever occurs first).
- I
Short Trip/City Intervals
At 6,000 Miles (10 000 km) -- .Then
Every 12,000 Miles (20 000 km): Tire Rotation.
Every 6,000 Miles (10 000 km) of Trailering:
Rear Axle Fluid Change (Vehicles Towing Trailers).
At the First 6,000 Miles (10 000 Ism): Rear Axle Fluid
Change (Limited-Slip Differential).
Every 15,000 Miles (25 000 km): Air Cleaner Filter
Inspection, if driving in dusty conditions. Automatic
Transmission Service (severe conditions only).
Every 30,000 Miles (50 000 km): Air Cleaner Filter
Replacement, Fuel Tank, Cap and
Lines Inspection.
Every 60,000 Miles (100 000 km): Engine Accessory
Drive Belt Inspection.
Every 100,000 Miles (166 000 km): Cooling System
Service
(or every 60 months, whichever occurs fust).
Spark Plug Wire Inspection. Spark Plug Replacement.
Automatic Transmission Service (normal conditions).
These intervals only summarize maintenance services.
Be
sure to follow the complete maintenance schedule on
the following pages.
7-4
ProCarManuals.com
Page 320 of 386

1 Short TripKity Maintenance Schedule 1
6,000 Miles (10 000 km)
0 Change engine oil and filter (or every
3 months, whichever occurs first).
An Emission Control Service.
0 Lubricate the steering linkage (or every
6 months, whichever occurs first).
0 Rotate tires. See “Tire Inspection and Rotation”
in the Index for proper rotation pattern and
additional mforrnation. Dwing tire rotation,
check
brake calipers for freedom of movement.
Refer to the appropriate
GM service manual for
proper caliper service procedures.
0 Change the rear axle gear lubricant if vehicle is used
to pull a trailer or has limited-slip merentid.
9,000 Miles (15 000 km)
0 Change engine oil and filter (or every
3 months, whichever occurs first).
An Emission Control Service.
. .I
DATE ACTUAL MILEAGE
!
SERVICED BY
-7
ProCarManuals.com