ignition PONTIAC FIREBIRD 1996 Service Manual

Malfunction Indicator Lamp (Service Engine Soon Light)
SERVICE
ENGINE
SOON
Your Pontiac is equipped
with a computer which
monitors operation of the
fuel, ignition and emission
control systems.
. . , , ..** , .- ,_ , . ,I , - . 'G, .. .. . .. .-
This system is called OBD I1 (On-Board
Diagnostics-Second Generation) and is intended to
assure that emissions are at acceptable levels for the life
of the vehicle, helping to produce a cleaner
environment. (In Canada, OBD
11 is replaced by
Enhanced Diagnostics.) The SERVICE ENGINE SOON
light comes on to indicate that there is a problem and
service
is required. Malfunctions often will be indicated
by the system before any problem is apparent, which
may prevent more serious damage to your vehicle. This
system
is also designed to assist your service technician
in correctly diagnosing any malfunction.
NOTICE:
If you keep driving your vehicle with this light
on, after a while, your emission controls may not
work as well, your fuel economy may
not be as
good and your engine may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running:If the light doesn't come on, have it repaired.
This light will also come on during a malfunction in one
of two ways:
0 Light Flashing -- A misfire condition has been
detected.
A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service
is required.
0 Light On Steady -- An emission control system
malfunction has been detected on your vehicle.
Dealer
or qualified service center diagnosis and
service may be required.
~ 2-83
ProCarManuals.com

NOTICE:
The oil level monitoring system only checks the oil level when you are starting your engine. It does not
keep monitoring the level once your
engine is running.
Also, the oil level check only
works when the engine has been turned
off long
enough for the oil to drain back into the oil pan.
Check Gages Light
CHECK GAGES
This warning light will
come on briefly when you
are starting the engine. If
the light comes on and stays
on while you are driving,
check your gages to see if
they are
in the warning
areas.
Fuel Gage
Your fuel gage shows about
how much fuel is in your
tank. The gage works only
when the ignition switch is
in the RUN position.
I I
When the gage pointer first indicates EMPTY (E), you
still have a little fuel left (about one to two gallons), but
you need
to get more right away.
Here are four concerns some owners have had about the
fuel gage. All these situations are normal and do not
indicate that anything is wrong with the fuel gage.
At the gas station, the gas pump shuts off before the
It takes more (or less) gas to fill up than the gage
gage
reads
FULL (F).
reads. For example, the gage reads half full, but it took
more (or less) than half of the tank’s capacity to fill it.
a The gage moves a little when you turn, stop or speed up.
When you turn the engine off, the gage doesn’t go
back to EMPTY (E).
2-87
ProCarManuals.com

Audio Systems
Your Delco@ audio system has been designed to operate
easily and give years of listening pleasure. You will get
the most enjoyment out of it if you acquaint yourself
with
it first. Find out what your Delco system can do
and how to operate all its controls, to be sure you’re
getting the
most out of the advanced engineering that
went into it.
If you have power door locks, your vehicle has a feature
called Retained Accessory Power
(RAP). With RAP you
can play your audio system even after the ignition is
off.
See “Retained Accessory Power” in the Index.
Setting the Clock for All Systems Except
AM-FM Stereo
Press and hold HR until the correct hour appears. Press
and hold
MIN until the correct minute appears. There
will
be a two-second delay before the clock goes into
time-set mode, and the colon
on the display will blink
while in this mode.
AM-FM Stereo with Cassette Tape Player
Playing the Radio
VOL: Push this knob to turn the system on or off. Turn
it clockwise to increase volume and counterclockwise to
decrease volume.
RECALL: Press this button briefly to recall the station
being played or
to display the clock. If you press the
knob when the ignition is
off, the clock will show for a
few seconds.
3-6
ProCarManuals.com

PROG (3): Press this button to play the other side of
the tape.
00 (4): Press this button to reduce background noise.
Note that the double-D symbol will appear on the
display.
Dolby@ Noise Reduction is manufactured under
a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol
are trademarks of
Dolby Laboratories Licensing Corporation.
REV (5): Press this button to reverse the tape rapidly.
Press it again to return to playing speed. The radio will
play the last-selected station while the tape reverses.
You
may select stations during REV operation by using
SEEK or TUNE.
FWD (6): Press this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while
the tape advances. You may select stations
during
FWD operation by using SEEK or TUNE.
AM-FM: Press this button to play the radio when a tape ~ '
is in the player.
TAPEPLAY; Press this button to change to the tape
function when the radio is
on. The tape symbol with an
arrow will appeq on the display when
the tape is active.
To return to playing the radio, press the
AM-FM buttm.
EJECT Press this button to remove the tape. The radio
will play. EJECT may be activated with either the
ignition or radio
off. Cassettes may be loaded with the
radio and ignition
off if this button is pressed first.
CLN: This message may appear on the display. If it
does, your cassette tape player needs to be cleaned.
It
will still play tapes, but you should clean it as soon as
possible to prevent damage to your tapes and player. See
"Care of Your Cassette Tape Player" in the Index. After
you clean the player, press and hold EJECT for five
seconds to reset
the CLN indicator. The radio will
display
--- to show the indicator was reset.
w ..
.-
3-9
ProCarManuals.com

AM-FM Stereo with Cassette Tape Player
and Equalizer
Playing the Radio
VOL: Push this knob to turn the system on or off. Turn
it clockwise to increase volume and counterclockwise to
: 'decrease volume.
RECALL: Press this button briefly to recall the station
being played or to display the clock.
If you press the
knob when the ignition is off, the clock wiIl show for a
few seconds.
Finding a Station
AM-FM: Press this button to get AM, FM1 or FM2.
The display shows your selection. If a cassette tape is
playing, press this button to play the radio.
TUNE: 'Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back in when
you're not using it.
SEEK: Press the up or down arrow to go to the next
higher or lower station.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2).
1. Press AM-FM to select the band.
2. Find the station you want by using
TUNE or SEEK.
3. Press and hold one of the six numbered buttons until
SET appears on the display. Whenever you press that
numbered button, the station you set will return.
4. Repeat the steps for each pushbutton.
Setting the Tone . .- I '.
EQUALIZER: A seven band equalizer is part of your
audio system. Slide the levers
up to boost or down to
reduce frequency range.
3-10
ProCarManuals.com

direction arrow blinks during NEXT or SEEK operation.
Press PREV or the
SEEK up arrow to stop searching.
The sound is muted during NEXT or SEEK operation.
PROG (3): Press this button to play the other side of
the tape.
(4): Press this button to reduce background noise.
Note that the double-D symbol will appear
on the
display.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double-D symbol
ark trademarks of Dolby
Laboratories Licensing Corp'oration.
REV (5): Press this button to'reverse the tape rapidly.
Press
it again to return to playing speed. The radio will
play the last-selected station while the tape reverses.
You may sel'ect stations during REV operation by using
SEEK or TUNE.
FWD (6): Press this button to advance quickly to
another part
of the tape. Press the button again to return
to playing speed. The radio will play
the last-selected
station while the tape advances.
You may select stations
during
FVJD operation by using SEEK or TUNE.
AM-FM: Press this button to play the radio when a tape
is
in the player.
WE/PLAX Press this button to change to the tape
function when the radio is on. The tape symbol with an
arrow will appear on the display when the tape is active.
To return to playing the radio, press the AM-FM button.
EJECT: Press this button to remove the tape. The radio
will play. EJECT may be activated with either the
ignition or radio
off. Cassettes may be loaded with the
radio
off if this button is pressed first.
CLN: This message may appear on the display. If it
does,
your cassette tape player needs to be cleaned. It
will still play tapes, but
you should clean it as soon as
possible to prevent damagt to. your tapes and player. See
"Care
of Your Cassette Tape Player" in the Index. After
you clean the player, press and hold EJECT for five
seconds to reset
the CLN indicator. The radio will
display
--- to show the indicator was reset.
3-12 ,
ProCarManuals.com

TREBLE: Slide the lever to the right or left to increase
or decrease treble. If a station is weak or noisy, slide the
lever down to reduce the noise.
Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn it to
move the sound to the left or right speakers. Use the
middle position to balance these speakers. Push the
knob
back in when you're not using it.
FADE: Press this knob lightly so it extends. Turn it to
move the
sound to the front or rear speakers. Use the
middle position to balance these speakers. Push the knob
back in when you're not using it.
Playing a Compact Disc
The integral CD player can play 8 cm "single"
mini-discs.
Insert a disc partway into
the slot, label side up. The
player will pull it in. The compact disc symbol
will
appear on the display. If the ignition is on, but the radio
is off, the disc will begin playing. CD will appear on the
display.
If you want to insert a disc when the ignition is
OFF, fist press EJECT.
If you're driving on a very rough road or if it's very hot,
the disc may not play and
E (error) 'and a number may
appear on the radio display.
If the disc comes out, it
could be that:
The disc is upside down.
It is dirty, scratched or wet.
The air is very humid. (If so, wait about an hour
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer.
If your radio
displays an error number, write it down and provide it to
your dealer when reporting the problem.
RECALL: Press this button to see what track is playing.
Press it again within five seconds to see how long it has
been playing (elapsed time). The track number also
appears when the disc is inserted, you change the
volume or when a new track starts playing.
PREV (1): Press this button or the SEEK down arrow to
go to the start of the current track if more than eight
seconds have played.
If you hold the button or press it
more than once, the player will continue moving back
through the disc.
and try
again.)
ProCarManuals.com

NEXT (2): Press this button or the SEEK up arrow to
go to the start of the next track if more than eight
seconds have played.
If you hold the button or press it
more than once, the player will continue moving
forward through the disc.
RDM (3): Press this button to hear the tracks in a
random order. It will change tracks in a random, rather
than sequential order. Press
RDM again to turn off
random play.
REV (5): Press and hold this button to quickly reverse
within a track (song). Release it to play the passage. YOU
will hear sound at a reduced volume. The display will
show elapsed time.
FWD (6): Press and held this button to quickly advance
within a track (song). You will hear sound at a reduced
volume. The display will show elapsed time.
AM-FM: Press this button to play the radio when a disc
is playing. The disc will stop but remain in the player.
CDPLAY. Press this button to change to the disc
function when the radio is
on.
EJECT Press this button to remove the disc or stop the
disc and switch to the radio. EJECT will work with
the
radio off.
AM-FM Stereo with Compact Disc Player
and Equalizer
Playing the Radio
VOL: Push this knob to turn the system on or off. Turn
it clockwise to increase volume and counterclockwise to
decrease volume.
RECALL: Press this button briefly to recall the station
being played or
to display the clock. If you press the
knob when the ignition is off, the clock will show for a
few seconds.
3-15
ProCarManuals.com

Finding a Station Setting the Tone
AM-FM:
Press this button to get AM, FM1 or FM2.
The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back in when
you're not using it.
SEEK: Press the up or d,own arrow to go to the next
higher or lower station.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2).
1. Press AM-FM to select the band.
2. Find the station you want by using TUNE or SEEK.
3. Press and hold one of the six numbered buttons until
SET appears on the display. Whenever you press that
numbered button, the station you set will return.
7
4. Repeat the steps for each pushbutton.
EQUALIZER: A seven band equalizer is part of your
audio system. Slide the levers up to
boost or down to
reduce frequency range.
Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn it to
move the
sound to the left or right speakers. Use the
middle position to balance these speakers.
Push the knob
back in when you're not using it.
FADE: Pressthis knob lightly so it extends. Turn it to
move the sound to the front or rear speakers. Use the
middle position to balance these speakers. Push the
knob
back in when you're not using it.
Playing a Compact,Disc
The integral CD player can play 8 cm "single"
mini-discs.
Insert a disc partway into the slot, label side up. The
player
will pull it in. If the ignition is on, but the radio is
off, the disc will begin playing. If you want to insert a
disc when the ignition is off, first press EJECT.
ProCarManuals.com

Theft-Deterrent Feature
THEFTLOCK" is designed to discourage theft of your
rabio. It works by using a secret code.to disable all radio
functions whenever battery power is removed.
The THEFTLOCK feature for the radio may be used or
radio
is not protected by the feature. If THEFTLOCK is
activated, your radio will not operate
if stolen.
When THEFTLOCK is activated, the radio will display
LOC to indicate a locked condition anytime battery
power is removed.
If your battery loses power for any
reason, you must
unlock the radio with the secret code
before-it will operate.
+ ignored. If ignored, the system plays normally an'd the
Activating the Theft-Reterrent Feature
The instructions which follow explain how to enter your
secret code to activate the
THEFTLOCK system. It is
recommended that
you read through all nine steps
before starting the procedure.
NOTE: If you allow more than 15 seconds to elapse
between any
steps, the radio automatically reverts to
time and you must start the procedure over at Step 4.
1. Write down any wee or four-digit number from
000 to 1999 and keep it in a safe place separate from
the vehicle.
2. Turn the ignition to the ACC or RUN position.
3. Turn the radio off.
4. Press the 1 and 4 buttons together. Hold them down
until
--- shows on the display. Next you will use the
secret code number which you have written down.
5. Press MIN and 000 will appear on the display.
6. Press MIN again to make the last two digits agree
7. Press PElR to make the first one or two digits agree
8. Press AM-FM after you have confirmed that the
with
your code.
with
your code.
code matches the secret code
you have written down.
The display will show REP to let you know that you
need to repeat Steps 5 through 7 to confirm your
secret code.
9. Press AM-FM and this time the display will show
SEC to let you know that your radio is secure.
ProCarManuals.com