alarm PONTIAC FIREBIRD 1996 Owners Manual

Door Locks
Unlocked doors can be dangerous.
Passengers
-- especially children -- can easily
open the doors and fall out. When a door
is
locked, the inside handle won’t open it.
Outsiders can easily enter through an unlocked
door when you slow
down or stop your vehicle.
This may not be so obvious: You increase the
chance of being thrown out of the vehicle in
a
crash if the doors aren’t locked. Wear safety belts
properly, lock your doors, and you will be far
better
off whenever you drive your vehicle.
There are several ways to lock and unlock your vehicle.
From’the outside, Use your door key. If your vehicle has
the Vehicle and Content Theft-Deterrent System and it
is armed, unlocking and opening a door
this way will set
off the alarm. See “Vehicle and Content Theft-Deterrent
System”
in the Index.
From the inside, to lock the door, move the lock
control on the door backward.
To unlock the door, move the lock control on the
door forward.
.’ ,
..
ProCarManuals.com

peration
The driver’s door will unlock automatically when
UNLOCK is pressed. If UNLOCK is pressed again
within five seconds, the passenger door will also unlock.
All doors will lock when LOCK
is pressed.
The hatch will unlock when the button with the trunk
symbol is pressed, as long as the ignition is turned to the
OFF position. If the ignition is in the RUN position, the
trunk symbol button will only work if
the transmission
is in PARK (P) for an automatic transmission, or if the
parking brake is set on a manual transmission.
The system will turn on the interior lamps for about
40 seconds (or until the ignition switch is turned t’o the
RUN position), when you unlock the doors or hatch.
The interior lamps will
go off when you lock the doors.
Operating the Remote Lock Control transmitter may
interact with the Vehicle and Content Theft-Deterrent
System (if
you have this option). See “Vehicle and
Content Theft-Deterrent System”
in the Index.
Alarm/Panic Mode
If your vehicle is equipped with the Vehicle and Content
Theft-Deterrent System, you will have a fourth button on
your Remote
Lock Control transmitter. This button is the
panic button. If you
are involved in a panic situation,
press this button and your vehicle’s horn will sound and the parking lamps will flash. This will draw needed attention
to you
and your vehicle. To turn this feature off,
either push the panic button again or turn the ignition to
the RUN position. Note: This feature will not work if
your ignition is in the
RUN position or if the remote
transmitter is
30 feet or more away from your vehicle.
Transmitter Range
The range of your Remote Lock Control system should
be about
30 feet (9 m). At times you may notice a
decrease
in the range. This is normal for any Remote
Lock Control system. If the transmitter does not work,
or you have to stand closer to your vehicle than normal
for the transmitter to work:
0
0
0
0
0
0
You may have to replace the battery in your transmitter.
See
the instructions8 for battery replacement.
You may be too far from your vehicle. Check your
distance. You may have to stand closer
to your
vehicle in rain or snow.
Check the location. Other
vehicles or objects may be
blocking the signal. Take
a few steps to the right or left.
You may have
to synchronize your transmitter to the
receiver in your vehicle. See the instructions for
synchronization.
You may have to match the transmitters to your
vehicle. See instructions for matching transmitters.
If none of the above apply, see your dealer or
qualified technician for service.
2-6
ProCarManuals.com

Hatch Release
Your door key opens the hatch.
If your vehicle has the Vehicle and Content
Theft-Deterrent System, and the system
is armed,
opening the hatch this way will trigger the alarm. First
&sarin the system or use the Remote Lock Control
transmitter to
open the hatch.
Remote Hatch Release (Option)
\
Press the switch under the lamp controls to unlock the
hatch
from inside y’our vehicle. If you have an automatic
transmission, your shift lever must be in
PARK (P)
or NEUTRAL (N) to use the switch. If you have a
manual transmission and the ignition switch is in
RUN, you must set the parking brake before you can
use the switch.
The switch only works when the ignition switch
is in
RUN or ACC, or when RAP is present. (See “Retained
Accessory Power” in the Index.)
ProCarManuals.com

NOTICE:
If you put things in the hatchback area, be sure
they won’t break the glass when you close it.
Never slam the hatch down.
You could break the
glass
or damage the defogger grid (if equipped).
On vehicles with the Vehicle and Content
Theft-Deterrent System: If the system has sounded an
alarm, the hatch switch will not work until the system is
disarmed. See “Vehicle and Content Theft-Deterrent
System” in the Index.
Theft
Vehicle theft is big business, especially in some cities.
Although your Pontiac has a number
of theft-deterrent
features, we
know that nothing we put on it can make it
impossible to steal. However, there
are ways you can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it’s an
easy tmget for joy riders or professional thieves -- so
don’t do it. When you
park your Pontiac and open the driver’s door,
you’ll hear a tone reminding
you to remove your key
from the ignition and take it with you.
Always do this.
Your steering wheel will be locked, and so will your
ignition. If you have an automatic transmission, taking
your key
out also locks your transmission. And
remember to lock the doors.
Parking at Night
Park in a lighted spot, close all windows and lock your
vehicle. Remember to keep your valuables out of sight,
Put them in a storage area,
or take them with you.
Parking Lots
If you park in a lot where someone will be watching
your vehicle, it’s best to lock it up and take your keys.
But what if you have to leave your ignition key? What
if
you have to leave something valuable in your vehicle?
0 Put your valuables in a storage area, like your
0 Lock the glove box.
Lock all the doors except the driver’s.
0 Then take the door key with you.
glove box.
2-11
ProCarManuals.com

Vehicle and Content Theft-Deterrent
System (Option)
If your vehicle has ths option, it has a theft-deterrent
alarm system. Once armed, the system will sound the horn
and
flash the parking lamps if the vehicle is broken into.
Shock Sensor
I
Coupe Convertible
The shock sensor is what triggers the alarm when it
detects a blow to your vehicle. It is located over the
right rear wheelhouse near the
spare tire in the hatch
area. There are two levels of
alarrns via the shock
sensor: Two horn blasts and parlung lamp flashes for
non-threatening blows to the vehicle and a full two
minute alarm for harder blows to the vehicle. Its
sensitivity can be adjusted if more or less sensitivity is
desired. (Note: If sensitivity increased too much, it may
give false alarms caused
by gusts of wind or other
natural events that may shake the vehicle).
To adjust, remove the label covering the adjustment knob
and adjust as desired. Turn clockwise to increase sensitivity.
Turn counterclockwise to decrease sensitivity. The shock
sensor
is ignored by the alarm system during ignition on,
when the hatch is open, when the alarm is &arm& when
customized to
be ignored and for five seconds after the horn
sounds an alarm or chq. The shock sensor is ignored after
triggering
three fuu. alarms until the system is rearmed.
Arming the System
The alarm system can be armed to detect break-ins by
locking your vehicle using the Remote Lock Control
transmitter
or by lochng the doors with the power door
lock switch. Passive
arming is also available, if you
would
like the system to arm all by itself after the doors
have
been closed for a short time. When the system is
armed, a red light will flash briefly once every two
seconds. (Note: If you return to your vehicle and the red
light is
flashing two brief flashes every two seconds, the
system
is armed and the shock sensor had triggered a
two minute alarm. If the red light is flashing three times
2-12
ProCarManuals.com

every two seconds, the system is armed and there was an
intrusion that sounded the alarm). Horn chirps and
parking lamp flashes can be set to your choice.
Remote Lock Control Transmitter Locking
If all the doors are closed, locking the vehicle with the
transmitter will immediately
arm the system. The horn
will chirp twice and the parking lamps will flash,
confirming that the system is armed.
If any door is open
when the transmitter LOCK button is pressed, the
system goes into an armed wait mode, waiting for the
doors to close. Once they are closed, the system will
arm, chirp the horns twice and flash the parking lamps.
If the hatch is open or ajar at the time the system is
arming, the horn will only chirp once.
Power Door Lock Switch Locking
If any door is open when the power door lock switch is
pressed, the system goes into
an armed wait mode,
waiting for the doors to close. Once they are closed, the
system will
arm and flash the parking lamps. If all of the
doors are closed when the lock switch is pressed, the
system assumes you are inside of the vehicle,
so it will
not
arm. Note: Locking the doors by using the manual
dm ‘Locks will not arm the system.
Passive Arming
If the ignition was just turned off and a door was
opened, the system will
arm six seconds after all doors
are closed, whether or not you lock them. In all other
cases, the system will wait
30 seconds after all doors are
closed before arming, allowing you time to get
into the
vehicle and the key in the ignition. The parking lamps
will flash when the system arms. Passive arming is not
enabled from the factory.
Disarming the System
There are two ways to disarm the system:
1. Press the UNLOCK button on the Remote Lock
Control transmitter.
If the horn chirps two or three
times when you unlock the car, the alarm sounded in
your absence.
lko chirps means that
the shock sensor was set
off and three chirps means
that a door or hatch was opened.
proper key.
2. Turn the ignition to the RUN position with the
For more information on customizing the features
mentioned here, see “Feature Customization” in
the Index.
2-13
ProCarManuals.com

Turning Off the Alarm
If you started the alarm by pressing the panic button on
the Remote Lock Control transmitter, you must either
push that button again or
turn the ignition switch to the
If the alarm is sounding due to the shock sensor or a
door
or hatch opening, it can be turned off by either
turning the ignition switch with
a proper keyinserted or
’ by pressing any button on the Remote Lock Control
transmitter. If you use your transmitter to silence
the
alarm, additional things will happen depending upon
which button you press.
Pressing the UNLOCK button will lurn the alarm off,
will unlock the driver’s door and disarm the system.
Pressing the LOCK button will turn the alarm off,
keep the ,doors locked and keep the system armed.
Pressing the trunk symbol button will turn the dam
off and will unlock and disarm the hatch only.
Pressing the panic button will turn the alarni off,
keep the doors locked and keep the system armed.
If the alarm is sounding because an incorrect ignition
key was used, press any button on the transmitter
to turn
the alarm off.
The alarm will stop by itself after two minutes.
, RUN position to stop the alarm.
PASS-Key 8 ‘1
Your vehicle is equipped
with the PASS-Key
II
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
II is a passive
theft-deterrent system.
It works when you insert
or remove the key
from
the ignition.
PASS-Key
11 uses a resistor pellet in the ignition key
that matches a decoder in your vehicle.
When the PASS-Key 11 system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel system. For about three minutes, the starter
won’t
work and fuel won’t go to the engine. If someone
tries to start your vehicle again or uses another key
during this time,
the vehicle will not start. This
discourages someone from randomly trying different
keys
with different resistor pellets in an attempt to make
a- match.
,
ProCarManuals.com

Feature Customization (Option)
Your Pontiac’s locks and lighting systems can be
programmed with several, different features.. The
features you can program depend upon the options that
came with your vehicle. The following list tells you the
features that can be programmed. Listed next
to each
feature is the option you need to have on your vehicle in
order to be able to program that particular feature.
Exit Lighting (available for all)
Delayed Illumination (available for all)
Last Door Closed Locking
(if equipped with power
door locks)
Lockout Prevention
(if. equipped with power
door locks)
Remote Lock Control Verification (if equipped with
Vehicle and Content Theft-Deterrent System)
Theft-Deterrent Arming.
Method (if equipped with
Vehicle and Content Theft-Deterrent System)
Theft-Deterrent Arming Verification
(if equipped
with Vehicle and Content Theft-Deterrent System)
Driver’s Door Alarm Delay (if equipped with
Vehicle and Content Theft-Deterrent System)
Shock Sensor Enable
(if equipped with Vehicle and
Content Theft-Deterrent System) To
program features, your vehicle must be
in the
programming mode. Follow these steps:
1. Put your key in the ignition.
2. Turn the ignition to the RUN position to disarm the
3. Turn the ignition to the OFF position.
4. Remove the RADIO fuse. This fuse is in the main
Vehicle .and Content Theft-Deterrent System.
fuse block, located on the left side of your
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
5. Put the ignirion in the ACC posmon.
You should hear a chime to veiify that the system is
in programming mode. If the chime sounds once,
you will be able to program Exit Lighting, Delayed
Illumination, Last Door Closed Locking and Lockout
Prevention only.
If the chime sounds twice and your
vehicle
is equipped with the Vehicle and Content
Theft-Deterrent System, you will also be able to set
Remote Lock Control Verification, Arming Method,
Arrning Verification, Driver’s Door Delay and Shock
Sensor Enable.
2-16
ProCarManuals.com

Theft-Deterrent Arming Method
Your vehicle comes with this feature set in Mode 3. This
means that both your Remote Lock Control transmitter
and the power door lock switch will actively arm the'
system. To change the factory setting, do the following:
1. Press the UNLOCK switch on the door.
2. Count the number of chimes you hear. The number of
,chimes tells you which mode your vehicle is set for.
3. Press the UNLOCK switch on the door until you
hear the number of chimes that correspond to the
mode selection you want.
Mode 1: Alarm System Off (The System will not arm).
Mode 2: Remote Lock Control Transmitter Lock (When
you lock your doors using the transmitter, the system
will
arm itself).
Mode 3: Remote Lock Control Transmitterh'ower Door
Lock Switch (If you use
either the transmitter or the
power door lock switch to lock the doors, the system
will
arm itself').
Mode 4: Passive arming and Remote Lock Control
Transmitterh'ower Door Lock Switch Arming (The
system will arm itself after
all doors are closed, plus
arming per mode
3).

Theft-Deterrent Arming Verification
Your vehicle comes with this feature set in Mode 3. This
means that if you arm the system using the Remote Lock
Control transmitter, your parking lamps will flash and
your horn will chirp twice to verify that the system
is
armed. If it only chirps once, the hatch is open or
unlatched. If you arm the system using either the power
door lock switch
or by passive arming, only the parking
lamps will flash for verification.
) To change the factory
setting, do the following:
1. Press the LOCK switch on the transmitter.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Press the LOCK switch on the transmitter until you
hear the number of chimes that correspond to the
mode selection you want.
Mode 1: All Off (No horn chirps or parking lamp flash).
Mode 2: Horn and Lamps (Your parking lamps will
flash and your horn will chirp twice to verify the system
is armed using any arming method).
ProCarManuals.com

Mode 3: Horn and LampsLamps (If you use the
transmitter to arm the system, your parking lamps will
flash and your horn will chirp twice
to verify that the
system is armed.
If you use either the power door lock
switch or passive arming, only your lamps will flash
for verification).
Mode 4: Lamps (When your vehicle arms, only your
parking lamps will flash for verification).
Driver’s Door Alarm Delay and Shock
Sensor Enable
Your vehicle comes with this feature set in Mode 4.
This means that if you open the driver’s door using
your key, the alarm will not
soand for eight seconds.
Also the sho’ck sensor, able
to detect sharp blows to
your vehicle is active. To change the factory setting, do
the following:
1.
2.
3.
Turn the parking lamps on and off.
Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
Turn the parking Imps on and off until you’hear the
number
of chimes that correspond to the mode
selection
you want.
Mode 1: Zero Del,ay and Shock Sensor Disabled (The
alarm will sound immediately if the driver’s door is
opened with your key and the shock sensor will not be
available
to measure sharp blows to your vehicle).
Mode 2: Eight Second Delay and Shock Sensor
Disabled (The alarm will sound eight seconds after the
driver’s door is opened with your key and the shock
sensor will not be available to measure sharp blows to
,
your vehicle).
Mode 3: Zero Delay and Shock Sensor Enabled (The
alarm will sound immediately after the driver’s door is
opened
with your key and the shock sensor will be
available to measure sharp blows to your vehicle).
Mode 4: Eight Second Delay and Shock Sensor Enabled
(The alarm will sound eight seconds’ after the driver’s
door is opened with your key and the shock sensor will
be available to measure sharp blows to your vehicle). :
Leaving Programming Mode
When programming is done, turn the ignition switch to
the
OW position and replace the RADIO fuse.
. ,,.
2-20
ProCarManuals.com