transmission PONTIAC G8 2009 User Guide

Sport Shift Mode
The automatic transmission has a
Sport Shift Mode. When you
are in the Sport Shift Mode the
vehicle will still shift automatically.
The transmission may remain
in a gear longer than it would in the
normal driving mode based on
braking, throttle input, and vehicle
lateral acceleration. To use this
feature, move the shift lever
over from D (Drive) to the right
quadrant. The Sport Shift message
in the DIC displays. If the shift
lever is not moved forward or
rearward, the vehicle remains in
sport mode.Performance Mode Lift Foot Mode
Within Sport Shift Mode there is a
further performance feature called
Performance Mode Lift Foot (PMLF)
Mode. The feature is activated
automatically when sports oriented
driving is detected, based on
cornering and on/off throttle
application. PMLF allows the
transmission to hold the current gear
instead of upshifting when the
throttle is lifted.
Driver Shift Control (DSC)
Notice:If you drive your vehicle
at high RPMs without upshifting
while using Active Select Mode,
you could damage the vehicle.
Always upshift when necessary
while using Active Select Mode.The automatic transmission has a
DSC mode that allows gear changes
similar to a manual transmission.
To use this feature:
1. Move the shift lever over from
D (Drive) to the right quadrant.
The Sport Shift message in
the DIC displays.
2. To enter the DSC mode, press
the shift lever forward to upshift
or rearward to downshift.
The Active Select On message
in the DIC will come on.
The DIC will indicate the requested
gear range when moving the
shift lever forward or rearward.
8-8 Driving and Operating

While using the DSC mode, the
vehicle has rmer shifting and
increased performance. This can be
used for sport driving or when
climbing or descending hills, to stay
in gear longer, or to down shift
for more power or engine braking.
The transmission will only allow the
driver to shift into gears appropriate
for the vehicle speed and engine
Revolutions Per Minute (RPM). The
transmission will not automatically
shift to the next lower gear if the
engine RPM is too high.
If shifting is prevented for any
reason, the currently selected gear
will ash multiple times, indicating
that the transmission has not
shifted gears.While in the DSC mode, the
transmission automatically
downshifts when the vehicle comes
to a stop.
When accelerating the vehicle from
a stop in snowy and icy conditions,
1st, 2nd or 3rd gear starts can
be selected from a standing start.
This is useful for gentle acceleration
on slippery surfaces.
To return to Normal Shift mode,
slide the shift lever over from
the right quadrant to the left into
D (Drive). A Normal Shift message
will be displayed in the DIC.
Normal Shift Mode is recommended
for normal or freeway driving, as
it provides optimum fuel economy.Powertrain Braking
For vehicles with a 6 speed
automatic transmission, there is
an additional feature known as
Powertrain Braking. When driving
on steep descents where frequent
braking is required, the vehicle
will automatically downshift to
provide engine braking assistance.
This feature also reduces brake
temperatures and wear.
Downshifting will only occur when
the driver’s foot is applied to
the brake. Active Select Mode can
be switched on to override the
feature and gain complete control of
shifts if desired.
Driving and Operating 8-9

Manual Transmission
Operation
This is the shift pattern for the
six-speed manual transmission.Here is how to operate the
transmission:
1 (First):Press the clutch pedal
and shift into 1 (First). Then slowly
let up on the clutch pedal as
you press the accelerator pedal.
You can shift into 1 (First) when
you are going less than 40 mph
(64 km/h). If you come to a complete
stop and it is hard to shift into
1 (First), put the shift lever in Neutral
and let up on the clutch. Press the
clutch pedal back down. Then shift
into 1 (First).
2 (Second):Press the clutch pedal
as you let up on the accelerator
pedal and shift into 2 (Second).
Then, slowly let up on the clutch
pedal as you press the accelerator
pedal.3 (Third), 4 (Fourth), 5 (Fifth) and
6 (Sixth):Shift into 3 (Third),
4 (Fourth), 5 (Fifth) and 6 (Sixth) the
same way you do for 2 (Second).
Slowly let up on the clutch pedal as
you press the accelerator pedal.
To stop, let up on the accelerator
pedal and press the brake
pedal. Just before the vehicle stops,
press the clutch pedal and the
brake pedal, and shift to Neutral.
Neutral:Use this position when you
start or idle the engine. The shift
lever is in Neutral when it is centered
in the shift pattern, not in any gear.
R (Reverse):To back up, press
down the clutch pedal and shift into
R (Reverse). Apply pressure to
get the lever past 5 (Fifth) and
6 (Sixth) into R (Reverse). Let up on
the clutch pedal slowly while
pressing the accelerator pedal.
8-10 Driving and Operating

One to Four Shift Light
When this light comes on, you can
only shift from 1 (First) to 4 (Fourth)
instead of 1 (First) to 2 (Second).
The light will be displayed on theinstrument panel cluster and a
message will be displayed in
the Driver Information Center.
You must complete the shift into
4 (Fourth) to turn off this feature.
This helps you get the best possible
fuel economy.
After shifting to 4 (Fourth), you may
downshift to a lower gear if you
prefer.
Notice:Forcing the shift lever
into any gear except FOURTH (4)
when the 1 TO 4 SHIFT light
comes on may damage the
transmission. Shift only from
FIRST (1) to FOURTH (4) when the
light comes on.
This light will come on when:
The engine coolant temperature
is higher than 169°F (76°C),
you are going 15 to 19 mph
(24 to 31 km/h) and
you are 21 percent throttle
or less.
Parking Brake
To set the parking brake, pull up on
the parking brake handle. If the
ignition is in the ON/RUN position,
the brake system warning light
will come on. SeeBrake System
Warning Light on page 4-15. Instrument Panel
Cluster
Driver Information
Center
Driving and Operating 8-11

To release the parking brake:
1. Hold the brake pedal down.
2. Pull the parking brake handle up
until you can press the release
button.
3. Hold the release button in as you
move the brake handle all the
way down.
Notice:Driving with the parking
brake on can overheat the brake
system and cause premature wear
or damage to brake system parts.
Make sure that the parking brake
is fully released and the brake
warning light is off before driving.
Driving with the park brake applied
will cause a warning chime to
sound and the Park Brake message
to appear in the DIC. The message
will remain on until:
the park brake is released
the vehicle comes to a stop.
If you are towing a trailer and you
are parking on a hill, seeTowing a
Trailer on page 9-89.
Shifting Into Park
(Automatic
Transmission)
{CAUTION
It can be dangerous to get out of
the vehicle if the shift lever is not
fully in P (Park) with the parking
brake rmly set. The vehicle can
roll. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, use the steps
that follow. If you are pulling a
trailer, seeTowing a Trailer on
page 9-89.Use this procedure to shift into
P (Park):
1. Hold the brake pedal down and
set the parking brake.
SeeParking Brake on page 8-11
for more information.
2. Move the shift lever into P (Park)
by holding in the button on the
shift lever and pushing the
lever all the way toward the front
of the vehicle.
3. Turn the ignition key to
LOCK/OFF.
4. Remove the key and take it with
you. If you can leave the vehicle
with the ignition key in your
hand, the vehicle is in P (Park).
8-12 Driving and Operating

Leaving Your Vehicle With the
Engine Running
{CAUTION
It can be dangerous to leave the
vehicle with the engine running.
The vehicle could move suddenly
if the shift lever is not fully in
P (Park) with the parking brake
rmly set. And, if you leave the
vehicle with the engine running, it
could overheat and even catch re.
You or others could be injured.
Do not leave the vehicle with the
engine running.
If you have to leave the vehicle with
the engine running, be sure the
vehicle is in P (Park) and the parking
brake is rmly set before you leave it.
After you have moved the shift lever
into P (Park), hold the brake pedal
down. Then, see if you can move the
shift lever away from P (Park) without
rst pushing the button.If you can, it means that the
shift lever was not fully locked
into P (Park).
Torque Lock
If you are parking on a hill and
you do not shift the automatic
transmission into P (Park) properly,
the weight of the vehicle may put too
much force on the parking pawl in
the transmission. You may nd it
difficult to pull the shift lever out of
P (Park). This is called torque lock.
To prevent torque lock, set the
parking brake and then shift into
P (Park) properly before you leave
the driver seat. To nd out how, see
“Shifting Into Park” previously in the
section.
When you are ready to drive, move
the shift lever out of P (Park) before
you release the parking brake.
If torque lock does occur, you may
need to have another vehicle
push yours a little uphill to takesome of the pressure from the
parking pawl in the transmission,
so you can pull the shift lever out
of P (Park).Shifting Out of Park
To shift out of P (Park):
1. Apply the brake pedal.
2. Press the shift lever button.
3. Move the shift lever to the
desired position.
If you still are unable to shift out of
P (Park):
1. Fully release the shift lever
button.
2. Hold the brake pedal down and
press the shift lever button again.
3. Move the shift lever to the
desired position.
If you still cannot move the shift
lever from P (Park), seeShift Lock
Manual Release on page 9-88.
Driving and Operating 8-13

Parking the Vehicle
(Manual Transmission)
If the vehicle has a manual
transmission, before you get out of
the vehicle, move the shift lever into
R (Reverse), and rmly apply the
parking brake. Once the shift lever
has been placed into R (Reverse)
with the clutch pedal pressed in,
turn the ignition key to LOCK/OFF,
remove the key and release the
clutch.
If you are parking on a hill, or if the
vehicle is pulling a trailer, see
Towing a Trailer on page 9-89.
Parking Over Things
That Burn
{CAUTION
Things that can burn could touch
hot exhaust parts under the vehicle
and ignite. Do not park over
papers, leaves, dry grass, or other
things that can burn.
Engine Exhaust
{CAUTION
Engine exhaust contains Carbon
Monoxide (CO) which cannot be
seen or smelled. Exposure to CO
can cause unconsciousness and
even death.
Exhaust may enter the vehicle if:
The vehicle idles in areas
with poor ventilation (parking
garages, tunnels, deep snow
that may block underbody
airow or tail pipes).
The exhaust smells or
sounds strange or different.
(Continued)
8-14 Driving and Operating

CAUTION (Continued)
The exhaust system leaks
due to corrosion or damage.
The vehicle’s exhaust system
has been modied, damaged
or improperly repaired.
There are holes or openings
in the vehicle body from
damage or after-market
modications that are not
completely sealed.
If unusual fumes are detected or if
it is suspected that exhaust is
coming into the vehicle:
Drive it only with the windows
completely down.
Have the vehicle repaired
immediately.
Never park the vehicle with the
engine running in an enclosed
area such as a garage or a
building that has no fresh air
ventilation.
Running the Vehicle
While Parked
It is better not to park with the
engine running. But if you ever have
to, here are some things to know.
{CAUTION
Idling a vehicle in an enclosed
area with poor ventilation is
dangerous. Engine exhaust may
enter the vehicle. Engine exhaust
contains Carbon Monoxide (CO)
which cannot be seen or smelled.
It can cause unconsciousness
and even death. Never run the
engine in an enclosed area that
has no fresh air ventilation. For
more information, see Engine
ExhaustEngine Exhaust on
page 8-14.
{CAUTION
It can be dangerous to get out
of the vehicle if the automatic
transmission shift lever is not fully
in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the
engine is running unless you have
to. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, always set the
parking brake and move the shift
lever to P (Park).
Follow the proper steps to be sure
the vehicle will not move. See
Shifting Into Park (Automatic
Transmission) on page 8-12.
If parking on a hill and pulling a
trailer, seeTowing a Trailer
on page 9-89.
Driving and Operating 8-15

The system may be heard or felt
while it is working. This is normal
and does not mean there is a
problem with the vehicle.
When this light and the STABILITY
CTRL OFF message is on and
the ESP OFF message is
displayed, the system will not
limit wheel spin.
Adjust your driving accordingly.
SeeDIC Warnings and Messages
on page 4-26for more information.ESP is automatically enabled
whenever the vehicle is started.
To limit wheel spin, especially
in slippery road conditions, always
leave the system enabled. ESP
can be turned off if needed.
It is recommended to leave the
system on for normal driving
conditions, but it may be necessary
to turn the system off if the
vehicle is stuck in sand, mud, ice or
snow, and you want to rock the
vehicle to attempt to free it. It may
also be necessary to turn off
the system when driving in extreme
off-road conditions where high
wheel spin is required. SeeIf Your
Vehicle is Stuck in Sand, Mud,
Ice, or Snow on page 8-29.The ESP button is located in front of
the transmission gear selector lever.
To turn the system off or on, press
and release the ESP button.
The DIC will briey display the
appropriate message and then
return to the trip computer display.
8-20 Driving and Operating

When this light and the STABILITY
CTRL OFF message is on briey and
the ESP OFF message is displayed
at the bottom of the DIC, the system
will not limit wheel spin.
If the ESP OFF message is always
displayed at the bottom of the
DIC when the button is pressed
to turn the system on or off, the
system needs repair. Contact your
dealer/retailer.The system is on when this light
and the STABILITY CTRL ON
message is displayed briey on
the DIC.
ESP Operation
ESP limits wheel spin by reducing
engine power to the wheels and
by applying brakes to each
individual wheel as necessary.
The ESP system is enabled
automatically when the vehicle
is started, and it will activate
the STABILITY CONTROL
ASSISTANCE light and the ESP
CTRL message on the DIC if it
senses that any of the wheels are
spinning or beginning to lose traction
while driving.Notice:If the wheel(s) of one axle
are allowed to spin excessively
while the ESC/TCS, ABS and
Brake warning lights and the
SERVICE ESC and/or SERVICE
TRACTION messages are
displayed, the differential could be
damaged. The repairs would not
be covered by the vehicle
warranty. Reduce engine power
and do not spin the wheel(s)
excessively while these lights and
this message are displayed.
The traction control system may
activate on dry or rough roads or
under conditions such as heavy
acceleration while turning or
abrupt upshifts/downshifts of the
transmission. When this happens,
a noise, vibration, or a reduction
in acceleration may be noticed.
This is normal.
Adding non-dealer/non-retailer
accessories can affect the vehicle’s
performance. SeeAccessories
and Modifications on page 9-3for
more information.
Driving and Operating 8-21