light PONTIAC GRAND PRIX 2007 Manual PDF

LOW WASHER FLUID
This symbol comes on
with this message.
This message displays when the windshield
washer uid is low. Fill the windshield washer uid
reservoir as soon as possible. SeeEngine
Compartment Overview on page 346for location
of the windshield washer uid reservoir. Also,
seeWindshield Washer Fluid on page 377
for more information.
This message displays only while the ignition is in
RUN. A chime sounds for two seconds when
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
PARKING BRAKE ON
This symbol comes on
with this message.
This message displays to alert the driver when the
vehicle’s parking brake is on, the ignition is in
RUN, and the vehicle speed is greater than 5 mph
(8 km/h). SeeParking Brake on page 115for
more information.
The brake system warning light also appears on
the instrument panel cluster when this message
appears on the DIC. SeeBrake System Warning
Light on page 176.
213

SERVICE STABILITY SYSTEM
This symbol comes on
with this message.
If the vehicle has the StabiliTrak
®Plus system,
this message displays when it is not functioning
properly. A warning light also appears on the
instrument panel cluster. SeeTraction Control
System (TCS) Warning Light on page 178
orEnhanced Traction System Warning Light on
page 179. SeeStabiliTrak
®Plus System on
page 295for more information. Have the
StabiliTrak
®Plus system serviced by your dealer
as soon as possible.This message displays only while the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
219

SERVICE TRACTION SYSTEM
This symbol comes on
with this message.
If the vehicle has the Traction Control
System (TCS), this message displays when the
system is not functioning properly. A warning light
also appears on the instrument panel cluster.
SeeTraction Control System (TCS) Warning Light
on page 178orEnhanced Traction System
Warning Light on page 179. SeeTraction Control
System (TCS) on page 292for more information.
Have the TCS serviced by your dealer as soon as
possible.This message displays only while the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
221

STABILITY CONTROL ACTIVE
This symbol comes on
with this message.
If the vehicle has the StabiliTrak
®Plus system,
this message displays when the system is
engaged and actively assisting the driver with
directional control of the vehicle. Slippery
road conditions may exist when this warning
message is displayed, so driving should be
adjusted accordingly. STABILITY CONTROL
ACTIVE also appears in the Head-Up
Display (HUD), if your vehicle has this feature.
This message displays only while the ignition is in
RUN. This message stays on until road conditions
change and StabiliTrak
®Plus is not active.
This message cannot be acknowledged and
cleared from the screen.
STABILITY CONTROL OFF
This symbol comes on
with this message.
If the vehicle has the StabiliTrak
®Plus system,
this message displays when the system turns off.
This message displays only while the ignition
is in RUN. A chime sounds once and the message
stays on for three seconds and then disappears.
A warning light indicating that this system is
deactivated also appears on the instrument panel
cluster. SeeTraction Control System (TCS)
Warning Light on page 178orEnhanced Traction
System Warning Light on page 179.
223

TRACTION CONTROL ACTIVE
This symbol comes on
with this message.
If the vehicle has the Traction Control System
(TCS), this message displays when the system is
on. TRACTION CONTROL ACTIVE also
appears in the Head-Up Display (HUD), if your
vehicle has this feature.
This message only displays while the ignition is in
RUN and will not disappear until driving
conditions change and the TCS is no longer
active.
This message cannot be acknowledged or cleared
from the screen.
TRACTION CONTROL OFF
This symbol comes on
with this message.
If the vehicle has the Traction Control System
(TCS), this message displays when the TCS turns
off. TRACTION CONTROL OFF also appears
in the Head-Up Display (HUD), if your vehicle has
this feature. This message only displays while
the ignition is in RUN and disappears after
three seconds. A chime sounds once and the
message stays on for three seconds and
then disappears. A warning light indicating that
this system is deactivated also appears on
the instrument panel cluster. SeeTraction Control
System (TCS) Warning Light on page 178or
Enhanced Traction System Warning Light
on page 179.
225

Entering the Personal Programming Mode
1. Turn the ignition on and make sure the
vehicle is in PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press the options button until PERSONAL
PROGRAMMING MODE appears on the DIC.
3. Press the set/reset button to display the rst
screen.
4. Press the options button to access these
modes:
Personal Programming Mode Screens
EXTERIOR LIGHTING DELAY:This screen
allows this feature to be turned off, or allows the
selection of the number of seconds the headlamps,
sidelamps, taillamps, fog lamps, and back-up
lamps are turned on after the key is removed from
the ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
If OFF is selected, the exterior lamps will not
turn on.If a time delay is chosen, the lamps will turn on for
the selected time. The time delay will be
cancelled and the exterior lamps will turn on
automatically when the key is removed from the
ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to the selection you want to program.
Choose from OFF, 15, 30, 60, or 90 seconds.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN DOOR CLOSED:This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the interior lamps will turn off
immediately when the ignition is turned off and the
last open door is closed.
If ON is selected, the interior lamps will stay on for
about 25 seconds after the vehicle’s ignition is
turned off and the last open door is closed.
227

To program this mode, use the following procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN KEY REMOVED:This
screen allows this feature to be turned OFF or
ON. This feature enables the interior lamps in the
vehicle to turn on for about 25 seconds after
the key is removed from the ignition.
If OFF is selected, removing the key from the
ignition will not cause the interior lamps to turn on.
If ON is selected, removing the key from the
ignition will cause the interior lamps to be turned
on for about 25 seconds.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.AUTO DOOR UNLOCK:This screen allows this
feature to be turned off, used for the driver’s
door only, or for all the doors.
If OFF is selected, none of the doors will unlock
when the vehicle’s transaxle is shifted into
PARK (P).
If DRIVER is selected, only the driver’s door will
unlock when the vehicle’s transaxle is shifted
into PARK (P).
If ALL is selected, all the doors will unlock when
the vehicle’s transaxle is shifted into PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF, DRIVER, or ALL.
2. Press the options button again to advance to
the next screen.
228

REMOTE LOCKS FEEDBACK:This screen
allows selection for this option to be turned OFF,
or gives the choice of two methods of verication;
LIGHTS or LIGHTS and HORN; that indicate
the vehicle’s doors are locked when the LOCK
button on the remote keyless entry transmitter is
pressed.
If OFF is selected, this feature will not be
programmed.
If LIGHTS is selected, the exterior lamps will ash
when the LOCK button on the remote keyless
entry transmitter is pressed.
If LIGHTS and HORN is selected, the exterior
lamps will ash when the LOCK button on
the remote keyless entry transmitter is pressed,
and the horn will sound when the LOCK button on
the remote keyless entry transmitter is pressed
again within ve seconds of the previous
command.To program this mode, use the following
procedure:
1. Press the set/reset button to scroll to OFF,
LIGHTS, or LIGHTS and HORN.
2. Press the options button again to advance to
the next screen.
If the vehicle does not have a content
theft-deterrent system, the next screens with
PROGRAMMING FINISHED and DISPLAY OFF
will appear.
If the vehicle does have a content theft-deterrent
system, the next screen will appear.
THEFT DETERRENT:The vehicle may have a
content theft-deterrent system. Once it is
turned on, the system will activate if someone tries
to enter the vehicle without using the remote
keyless entry transmitter or the correct key. This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the content theft-deterrent
system will not function.
If ON is selected, the content theft-deterrent
system will be activated.
230

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered pushbuttons, by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM, or XM1
or XM2.
3. Tune in the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. Whenever
that numbered pushbutton is pressed,
the station that was set returns and the
equalization that was selected is stored for
that pushbutton.
6. Repeat the steps for each pushbutton.
Setting the Tone
(Bass/Midrange/Treble)
TONE:Press and release this button until BASS,
MID (midrange), or TREB (treble) displays. The
SELECT LED indicator lights to show that the tone
control can be adjusted. Turn the SELECT knob
to increase or to decrease. If a station is weak
or has static, decrease the treble.
To return all of the tone controls to the middle
position, press and hold the TONE button
until FLAT displays.
EQ (Equalizer):Press this button to select
customized equalization settings.
Up to six customized equalization settings, can be
programmed, by performing the following steps:
1. Turn the radio on.
2. Use the TONE button and the SELECT knob
to create the equalization.
3. Press and hold the EQ button for two seconds.
SELECT EQ # displays and the EQ symbol
ashes.
4. Press EQ or turn the SELECT knob to select
the EQ number.
238

5. Press and hold the EQ button or push the
SELECT knob to store the equalization
setting and the number. EQ SAVED displays
and a beep sounds.
6. Repeat the steps for the other EQ settings
and numbers.
EQ 5 has been programmed at the factory for
use with talk radio, but it can be preset to a
different tone.
Adjusting the Speakers (Balance/Fade)
BAL (Balance):To adjust the balance between
the right and the left speakers, press and release
this button until BAL displays. The SELECT
LED indicator lights to show that the speakers can
be adjusted. Turn the SELECT knob to move
the sound toward the right or the left speakers.
FADE:To adjust the fade between the front and
the rear speakers, press and release this
button until FADE displays. The SELECT LED
indicator lights to show that the speakers can be
adjusted. Turn the SELECT knob to move the
sound toward the front or the rear speakers.
Pressing and holding the BAL FADE button for
two seconds returns all speaker settings to
the middle position.
Finding a Program Type (PTY) Station
(RDS and XM™)
To select and nd a desired PTY perform the
following:
1. Press the PROG TYPE button to activate
program type select mode. PTY displays.
2. Turn the SELECT knob to select a PTY.
3. Once the desired PTY displays, press either
SEEK arrow to select the PTY and take you
to the PTY’s rst station.
4. To go to another station within that PTY, while
the PTY displays, press either SEEK arrow
once. If the PTY is not displayed, press either
SEEK arrow twice to display the PTY and
then to go to another station.
5. Press PROG TYPE to exit program type
select mode.
If PTY times out and is no longer on the
display, go back to Step 1.
If both PTY and TRAF are on, the radio searches
for stations with the selected PTY and traffic
announcements.
239