stop start PONTIAC VIBE 2008 Owners Manual
[x] Cancel search | Manufacturer: PONTIAC, Model Year: 2008, Model line: VIBE, Model: PONTIAC VIBE 2008Pages: 368, PDF Size: 5.7 MB
Page 7 of 368

Seat Height Adjuster
The driver seat height adjuster is located on the
outboard side of the seat. To raise the seat, pull up
on the lever repeatedly until the seat is at the desired
height. To lower the seat, push down on the lever
repeatedly until the seat is at the desired height.
It is easier to use the adjuster when the seat is
unoccupied.
Reclining Seatbacks
{CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver’s seat while the vehicle
is moving. The sudden movement could startle
and confuse you, or make you push a pedal
when you do not want to. Adjust the driver’s
seat only when the vehicle is not moving.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
The seats have manual reclining seatbacks. The lever
used to operate them is located on the outboard side
of the seats.
1-3
Page 89 of 368

Testing the Alarm
To test the alarm:
1. Open all the windows.
2. Set the system as described in the previous
procedure. The doors and liftgate should be locked
with the key or RKE transmitter. Be sure to wait
until the security light starts ashing.
3. Unlock the driver’s door from the inside.
The system should activate the alarm.
4. Stop the alarm as described in the disarming
procedure following.
5. Repeat this operation for the other doors.
Also check that the system is activated when
the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it
checked by your dealer/retailer.
How the System Alarm is Activated
The system will activate the alarm:
If the driver’s or front passenger’s door is unlocked
without using the key or RKE transmitter.
If any door or the liftgate/liftglass is forcibly opened
without the key or RKE transmitter.
If the battery terminal is disconnected and then
reconnected.
If the ignition is hot-wired.
If the side window glass is broken or damaged.
The security light will come on when the system
is activated.
If the driver’s or front passenger’s doors are unlocked
without using the key or RKE transmitter, the other doors
and the liftgate will be automatically locked again.
After one minute the alarm will automatically stop and
the security light will start ashing again.
2-17
Page 90 of 368

Reactivating the System
Once the system is set, it will automatically reset the
alarm after the alarm stops. The alarm will activate again
under the same conditions as described earlier.
Disarming the System
To disarm the alarm:
Turn the ignition key from LOCK/OFF to ON/RUN.
Unlock any of the doors with the key or with the
RKE transmitter.
If the liftgate or liftglass is opened with the key,
the system will still be activated.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an elaborate
break-in. But it will perform better in the long run if
you follow these guidelines:
Do not drive at any one constant speed, fast
or slow, for the rst 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake or slow the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
the new brake linings are not yet broken in.
Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every
time you get new brake linings.
Do not tow a trailer during break-in.
SeeTowing a Trailer on page 4-27for
the trailer towing capabilities of your
vehicle and more information.
Following break-in, engine speed and load can be
gradually increased.
2-18
Page 92 of 368

(C) ON/RUN:This is the position the switch returns to
after you start your engine and release the switch. The
switch stays in the ON/RUN position when the engine is
running. But even when the ignition is not running, you
can use ON/RUN to operate your electrical accessories,
including the ventilation fan and 115 volt power outlet,
and to display some warning and indicator lights.
The battery could be drained if you leave the key in the
ACC/ACCESSORY or ON/RUN position with the engine
off. You may not be able to start your vehicle if the battery
is allowed to drain for an extended period of time.
(D) START:This position starts the engine. When
the engine starts, release the key. The ignition switch
will return to ON/RUN for normal driving.
When the engine is not running, ACC/ACCESSORY
and ON/RUN allow you to operate some of your
electrical accessories.
A warning tone will sound if you open the driver’s door
when the ignition is still in ACC/ACCESSORY or
LOCK/OFF and the key is in the ignition.Key In the Ignition
Never leave your vehicle with the keys inside, as it is an
easy target for joy riders or thieves. If you leave the key in
the ignition and park your vehicle, a chime will sound,
when you open the driver’s door. Always remember to
remove your key from the ignition and take it with you.
This will lock your ignition and transmission. Also, always
remember to lock the doors.
The battery could be drained if you leave the key in the
ignition while your vehicle is parked. You may not be
able to start your vehicle after it has been parked for
an extended period of time.
Starting the Engine
Move the transmission in the proper gear.
Automatic Transmission
Move the shift lever to PARK (P) or NEUTRAL (N).
The engine will not start in any other position -- this
is a safety feature. To restart when you are already
moving, use NEUTRAL (N) only.
Notice:Do not try to shift to PARK (P) if your
vehicle is moving. If you do, you could damage
the transmission. Shift to PARK (P) only when
your vehicle is stopped.
2-20