clutch PORSCHE 911 GT2 2008 5.G Information Manual

· 37 · · 36 ·
The 911 GT2 |Drive
benefits, such as optimum econ-
omy, emissions and performance
in all driving scenarios.
One of the most important tasks
performed by the engine manage-
ment system is cylinder-specific
knock control. By preventing pre-
ignition at high engine speeds
and loads, this function can avert
costly damage to the pistons and
cylinders. Since temperatures
tend to vary across the engine,
each cylinder is monitoredseparately. If a risk is detected,
the individual ignition timing is
adjusted.
The on-board diagnostics system,
designed to European standard,
quickly detects any faults in the
exhaust and fuel system and
displays them during driving
via the car’s instruments. The
benefits include active prevention
of harmful emissions as well
as consistent rates of fuel con-
sumption.Input data Used to regulate /control
Digital engine electronics
(ME7.8.1 control unit)
Engine load
Pressure upstream from throttle
Throttle-valve angle
Engine speed (from crankshaft)
Inlet camshaft phase angle
Throttle-pedal position
Oxygen sensor signals
Knock sensor signals
Ignition
Fuel injection
Throttle valve
Heating elements in oxygen sensors
Fuel pump
Fuel-tank venting
CAN interface to transmissionMoment interface to Porsche
Stability Management (PSM)
VarioCam Plus
– camshaft phase angle
– valve lift control
Electronic controller for
Variable Turbine Geometry (VTG)
Recirculation valve
Secondary air injection
Engine-bay fan
Starter
On-board diagnostics
Air-conditioning compressor
Interface to instrument cluster
Radiator fans (front control unit via CAN)
Vehicle speed
Air-conditioning settings
Engine immobiliser status
Clutch pedal switch
Ambient air pressure
Temperatures
– coolant
– air upstream from throttle
– engine oil
– air in engine compartment
– ambient air
Exhaust-gas temperature
Engine management system.
The Motronic ME7.8.1 engine
management system facilitates
optimum performance at all
times. This high-precision ECU
controls all engine-related func-
tions and assemblies (see
dia-
gram), such as Variable Turbine
Geometry, VarioCam Plus and
the electronic throttle, one of the
key prerequisites for the standard
Porsche Stability Management
(PSM). This produces various

· 39 · · 38 ·
The 911 GT2 |Drive
The six-speed manual gearbox in
the 911 GT2 is specifically
designed for the high engine
performance. The individual ratios
are carefully matched to the spe-
cific characteristics of the engine.The gear-lever throw is short and
precise, enabling fast and
accurate gearshifts.
A typical feature of the 911 GT2
is the Launch Assistant – for maximum acceleration from a
standing start. The clutch and
accelerator are depressed when
the vehicle is stationary.
When a
boost pressure of approximately
0.9 bar is displayed in the instru-ment
cluster, release the clutchas
quickly as possible and maximum
a
cceleration automatically ensues.
Normally on a turbocharged vehicle
with manual gearbox, the boost
pressure under acceleration from
a standing start is relatively low.
The turbo effect is delayed as
the engine gathers speed and
the boost pressure starts to build.On the 911 GT2, this initial delay
is reduced. While the car is still
stationary, the fuel injection is
modified to help the engine reach
maximum output earlier. The boost
pressure is significantly increased
and the engine readied for a faster
start.
A specially designed traction
control system adapts the acceler-
ation procedure automatically
in the ECU to ensure optimum
traction. The clutch remains
engaged. This reduces load and
prevents high clutch wear. The
power is transmitted directly to
the road via the rear axle.
The gearbox is combined with
a cable linkage and dual-mass fly-
wheel offering added comfort and
precision. The close ratio spread
enables powerful acceleration
within the optimum engine power
band.
Steel baulk rings on gears two to
five ensure a precise gearshift
action even under extreme loads.Cooling is provided by an add-
itional oil-to-water heat exchanger
and spray lubrication. Both of
these features are essential for
durability in endurance racing
conditions.
Other standard features include
a limited-slip differential with
asymmetrical lock factor. Offering
better traction and handling
when exiting a corner, it applies a
higher proportion of drive torque
to the loaded outer rear wheel.
The term ‘asymmetrical’ means
that one lock factor is applied
when cornering under power
(28 %), and another when braking
for a corner (40 %).
Maximum response to minimum effort.
Transmission.