lights PORSCHE 911 TURBO 2014 6.G User Guide
[x] Cancel search | Manufacturer: PORSCHE, Model Year: 2014, Model line: 911 TURBO, Model: PORSCHE 911 TURBO 2014 6.GPages: 300, PDF Size: 10.61 MB
Page 39 of 300
Seats, Mirrors and Steering Wheel 37
Safety-belt pretensioner
Front safety belts are tightened in an accident, depending on the force of the collision.
The safety-belt pretensioners are triggered: – In the event of front and rear impact– In the event of side impact– If the vehicle turns over
Information
The safety-belt pretensioner system can be triggered only once; the system must then be replaced. Work may be carried out on the safety-belt pretensioner system only by qualified specialist employees from an authorized Porsche dealer.Smoke is released when the safety-belt pretensioners are triggered. This does not indicate a fire in the vehicle.
Safety belt Warning light and warning message
An audio-visual warning system is interconnected with the driver’s safety belt.
Every time the ignition is turned on, the gong will sound for about 6 seconds to remind driver and passenger to buckle up.In addition, the gong will sound for approximately 90 seconds if vehicle speed exceeds 15 mph(24 km/h).The safety belt warning lights in the instrument panel and multi-purpose display will go off as soon as the driver has buckled up.
Fasten safety belt
1. Assume a comfortable sitting position. 2. Adjust the seat backrest so that the belt always rests on your upper body and runs across the middle of your shoulder.3. Grasp the belt tongue and pull the belt in a slow, continuous motion across your chest and lap.
Information
The belt may be blocked if the vehicle is standing at an angle or the belt is pulled out using a jerking movement.The belt cannot be pulled out while accelerating and slowing down, when cornering and when driving uphill.
4. Insert the belt tongue into the appropriate buckle on the inboard side of the seat until it locks securely with an audible click.5. Make sure that belts are not trapped or twisted and that they are not rubbing on sharp edges.6. The horizontal section of the belt should always fit snugly across the pelvis. Therefore, after fastening the belt, always pull the diagonal part of the belt upward.Pregnant women should position the belt as low as possible across the pelvis, and ensure that it is not pressing against the abdomen.7. Also pull on the diagonal section of the belt now and again during the journey to ensure that the horizontal section remains tight.
14_991_Turbo_21.book Seite 37 Mittwoch, 9. April 2014 2:19 14
Page 44 of 300
42 Seats, Mirrors and Steering Wheel
Information
fAfter switching on the ignition, the PASS AIR BAG OFF warning light lights up for a few seconds as a check.
PASS AIR BAG OFF indicator lamp lights up
The passenger airbag is switched off.
PASS AIR BAG OFF indicator lamp does not light up
The passenger airbag is active and ready for operation.
Risk of serious personal injury or death due to the passenger airbag triggering unintentionally.
When the ignition is on and the up to one-year old child is seated in the child restraint system on the passenger seat the indicator lamp “PASS AIR BAG OFF“ must be on.
If the “PASS AIR BAG OFF” indicator lamp does not light up, it could indicate a fault in the system, and the airbag could inflate in a collision, placing the child at risk of death or severe injury from the inflating airbag.In this case:fChild restraint systems facing forwards: Install on the rear seats.fChild restraint systems facing rearwards: Do not drive with a rearward facing child restraint system.fHave the fault remedied at your nearest authorized Porsche dealer.
Airbag Warning light
Faults are indicated by a warning light on the tachometer.
The airbag warning light illuminates when the electronic monitoring of the airbag system detects a malfunction of the sensors, safety belt system, occupant detection system, PASS AIR BAG OFF indicator lamp, related wiring, airbag modules and control units.fIn the following cases you should immediately consult an authorized Porsche dealer in order to assure the airbag system is functioning properly: – If the warning light does not light up when the ignition is switched on or – If the warning light does not go out once the engine is running or – If the warning light appears while driving.
Information
If you sell your Porsche, notify the purchaser that the vehicle is equipped with airbags, and refer them to the chapter “Airbag systems“ in the owner’s manual (safety and disposal rules).
Further information on the airbag system can be found on stickers attached to the sun visors, as well as on all airbag components.
For special recommendations on the use of child restraints:fPlease see the chapter “CHILD RESTRAINT SYSTEMS” on page 42.
Child Restraint Systems
Porsche recommends that all infants and children be restrained in child restraint systems at all times while the vehicle is in motion in accordance with applicable laws.
When possible, use only child restraint systems recommended by Porsche. These systems have been tested and adjusted to the interior of your Porsche and the appropriate child weight groups.Other systems have not been tested and could entail an increased risk of injury.
The use of infant or child restraints is required by law in all 50 US states and the Canadian provinces. The child restraint system should be one that complies with U.S. Federal/Canadian Motor Vehicle Safety Standards and should be secured by a lap belt portion of a lap-shoulder belt or for child seats equipped with the LATCH system ( Lower Anchorage and Tether for Children, also known as ISOFIX) to the LATCH anchorages.
All child restraint systems are designed to be secured in vehicle seats by lapbelts or the lapbelt portion of a lap-shoulder belt.
You can obtain child seats that are LATCH compatible at your authorized Porsche dealer.fAlways observe the separate installation instructions for your child seat.
Children could be endangered in a crash if their child restraints are not properly secured in the vehicle.fMake sure that all child restraints are properly secured.
DANGERh
Improper use of child restraint
DANGERh
14_991_Turbo_21.book Seite 42 Mittwoch, 9. April 2014 2:19 14
Page 46 of 300
44 Seats, Mirrors and Steering Wheel
Information
If a child seat with top tether is adapted for use on the front seat, do not use Toptether in the rear.
Using child restraint systems in the front passenger seat
The use of a child restraint system in the front passenger seat can result in serious personal injury or death to the child from an airbag deployment.To reduce risk of injury from an inflating airbag in an accident, Porsche strongly recommends:fPlease see the chapter “PASS AIR BAG OFF INDICATOR LAMP DOES NOT LIGHT UP” on page 42.
However, there may be serious situations where it might be necessary to place a child in the front seat so that he/she can be kept under direct observation to prevent an immediate risk to the child (for example, while driving to the doctor or hospital). The following instructions are provided to you solely for that purpose.fSeek appropriate advice from your authorized Porsche dealer about the possible installation of a Porsche child restraint system.fIf a child restraint system must be fastened to the passenger's seat, adjust the passenger's seat as far away from the airbag as possible.fIf emergency or other serious conditions require a child to be placed in the front seat, exercise extreme caution and defensive driving of your vehicle.
Child restraint system for up to one-year old children
If the child restraint system must be fastened to the passenger’s seat in exceptional cases:– When an up to one-year old child is seated in the child restraint system, the front airbag is automatically deactivated on the passenger side.fMake sure that the “PASS AIR BAG OFF” indicator lamp lights up.fAdjust the passenger’s seat as far away from the airbag as possible.
When the ignition is on and the up to one-year old child is seated in the child restraint system on the passenger seat the indicator lamp “PASS AIR BAG OFF” must be on.
If the “PASS AIR BAG OFF” indicator lamp does not light up, it could indicate a fault in the system, and the airbag could inflate in a collision, placing the child at risk of death or severe injury from the inflating airbag.In this case:fChild restraint systems facing forwards: Install on the rear seats.fChild restraint systems facing rearwards: Do not drive with a rearward facing child restraint system.fHave the fault remedied at your nearest authorized Porsche dealer.
Child Restraint in Front Seat
DANGERh
Child Seat Detection Fault
DANGERh
14_991_Turbo_21.book Seite 44 Mittwoch, 9. April 2014 2:19 14
Page 47 of 300
Seats, Mirrors and Steering Wheel 45
Child restraint system for children older than one year
Your vehicle is equipped with occupant sensing for the passenger's seat in accordance with U.S. Federal Motor Vehicle Safety Standard 208. Depending on the weight, body positioning and shape acting on the passenger's seat, the passenger's airbag will automatically be switched on or off.fIn case of doubt, fasten the child restraint system on the rear bench.
Small adult passengers
fMake sure that the PASS AIR BAG OFF indicator lamp does not light up.
When the ignition is on and the small adult passenger is seated on the passenger seat, the indicator lamp “PASS AIR BAG OFF” must be off.
If the “PASS AIR BAG OFF” indicator lamp lights up, it could indicate a fault in the system.In this case:fHave the fault remedied at your nearest authorized Porsche dealer.
Automatic locking retractor
The safety belts for the front passenger and rear seats are equipped with an automatic locking retractor for securing the child restraint system. When activated, this retractor allows you to securely fasten the child restraint system in place so that inadvertent movements will not occur.
The use of a child restraint system on the front passenger seat can result in serious personal injury or death to the child from an airbag deployment.To reduce risk of injury from an inflating airbag in an accident, Porsche strongly recommends:fUnder all normal circumstances, the child seat must be placed in the rear. Do not use a child restraint system on the front passenger seat.
If there are emergency reasons for transporting a child in the front passenger seat, use a child restraint seat and the automatic locking retractor function. Follow the other safety instructions on the previous pages in this section.
PASS AIR BAG OFF indicator lamp
fAfter fastening the child restraint system, do not adjust the seat in any direction.
Moving the seat could adjust the safety belt against the child restraint and cause the “PASS AIR BAG OFF” indicator lamp to go off and activate the airbag system.fCheck the condition of the passenger airbag system shown by the indicator lamp in the overhead operating console.
Adult Use of Front SeatsCAUTIONh
Child Seat in FrontDANGERh
Adjusting Child seat After Fastening
DANGERh
14_991_Turbo_21.book Seite 45 Mittwoch, 9. April 2014 2:19 14
Page 51 of 300
Seats, Mirrors and Steering Wheel 49
Exterior Mirrors
The convex mirror on the passenger’s side and the aspherical mirror on the driver’s side provide a larger field of view.
Vehicles or objects appear smaller in convex mirrors and further away than they are in reality.fBear this distortion in mind when estimating the distance of vehicles behind you and when reversing into a parking space.fAlso make use of the interior mirror for judging distance.
Risk of damage to the exterior mirrors when washing the vehicle in a car wash.fFold in exterior mirrors before using the car wash.
A - Exterior mirror selection – driver’s side B - Exterior mirror selection – passenger's side C - Adjusting exterior mirrors D - Folding in exterior mirrors electrically (where equipped)
Adjusting exterior mirrors
The electrical exterior mirror adjuster is ready for operation:– With ignition switched on.– After the ignition is switched off and before the driver’s or passenger’s door is first opened, but for a maximum of 10 minutes.
1. Press selection button A for the driver’s side and selection button B for the passenger’s side.The indicator light on the pressed button lights up.2. Move the exterior mirrors to the correct position by pressing the adjustment button C.
If the electrical adjustment facility fails
fAdjust the mirror by pressing on the mirror face.
Folding in exterior mirrors manually
fSwivel the mirror housing inwards by hand as far as it will go.
Folding out exterior mirrors manually
fSwivel the mirror housing outwards by hand as far as it will go.
Judging Distance in Convex Side Mirror
WARNINGh
NOTICE
14_991_Turbo_21.book Seite 49 Mittwoch, 9. April 2014 2:19 14
Page 53 of 300
Seats, Mirrors and Steering Wheel 51
Information
The anti-dazzle function switches off automatically if:– Reverse gear is engaged or– Interior lighting is switched on.
Switching on automatic anti-dazzle function
fPress button B. The indicator light A lights up.
Electrolyte fluid may escape from broken mirror glass. This fluid irritates the skin and eyes.fIf the electrolyte fluid should come into contact with the skin or eyes, rinse it off immediately with clean water.Seek medical attention if necessary.
Risk of damage to paintwork, leather, plastic parts and clothing.
Electrolyte fluid can be removed only while it is still wet.fClean the affected parts with water.
Automatic anti-dazzle exterior mirror
The exterior mirrors change to anti-dazzle position automatically in synchronization with the interior mirror.
Steering Wheel Heating
The steering wheel heating can be switched on and off using the button on the rear of the steering wheel when the ignition is switched on.
Switching steering wheel heating on/off
fPress button.The message “ Steering wheel heating switched on ” or “Steering wheel heating switched off ” appears on the multi-function display for 2 seconds.
Steering Wheel Adjustment
The steering wheel can be adjusted electrically in four directions depending on the vehicle equipment.
The steering wheel may move further than desired if you attempt to adjust it when driving.You may lose control of the vehicle.fDo not adjust the steering wheel when driving.
If persons or animals are in the movement range of the steering wheel during adjustment or if the person buttons are pressed unintentionally when the vehicle is at a standstill, parts of the body could get trapped or crushed.fDo not leave children in the vehicle unattended.
Electrolyte fluid may escape if the mirror glass is broken
CAUTIONh
NOTICE
Steering Wheel Adjustment While Driving
Memory Steering Wheel Movement
WARNINGh
CAUTIONh
14_991_Turbo_21.book Seite 51 Mittwoch, 9. April 2014 2:19 14
Page 58 of 300
56 Air Conditioning
A/C mode
In automatic mode, A/C mode is activated by default.The power for the air conditioning compressor is fully controlled by the air conditioning system depending on the current operating requirements.The air-conditioning compressor is switched off automatically at outside temperatures of less than approx. 36 °F (2 °C).
Switching A/C mode on
If you wish to cool the passenger compartment to a temperature lower than the outside temperature, A/C mode must be activated.fPress button A/C OFF. The indicator light on the button goes out.The air-conditioning compressor is switched on.orPress button AUTO/SYNC. The cooling function is activated.
Switching A/C mode off
A/C mode can be switched off manually to save fuel, for example.fPress button A/C OFF. The indicator light on the button lights up.The air-conditioning compressor is switched off.The cooling function is deactivated.
SYNC mode
In SYNC mode, the temperatures on the driver’s and passenger’s side are synchronized and are regulated via button TEMP on the driver’s side.
Switching on SYNC mode
fPress button AUTO/SYNC and hold until SYNC appears on the display.fRegulate the temperature on the driver’s and passenger’s side via button TEMP on the driver’s side.
Switching off SYNC mode
fPress button AUTO/SYNC or button TEMP on the passenger’s side.
A/C MAX mode
In A/C MAX mode, the passenger compartment is cooled at maximum power.The interior temperature is not regulated automatically.
If the vehicle has been in the sun for a long
time, it is a good idea to ventilate the interior
briefly with the windows open.
Switching A/C MAX mode on
fPress button A/C MAX. The indicator light on the button lights up.
Switching A/C MAX mode off
fPress button A/C MAX. The indicator light on the button goes out.orPress button AUTO/SYNC.
14_991_Turbo_21.book Seite 56 Mittwoch, 9. April 2014 2:19 14
Page 59 of 300
Air Conditioning 57
Defrosting windshield
Activating defrosting function
fPress button . The indicator light on the button lights up.The air flows to the windshield and the front side windows.The windshield is demisted or defrosted as quickly as possible.
Deactivating defrosting function
fPress button . The indicator light on the button goes out.orPress button AUTO/SYNC.
Air-recirculation mode
Switching on air-recirculation mode
fPress button . The indicator light on the button lights up.The outside-air supply is interrupted and only the inside air is recirculated.
Switching air-recirculation mode off
fPress button . The indicator light on the button goes out.
Information
If the air-conditioning compressor is switched off manually or automatically, recirculated air mode ends after approx. 3 minutes.
Setting automatic air-recirculation mode
In automatic air-recirculation mode, the fresh air supply is adjusted depending on the air quality.
Automatic air-recirculation mode can be switched on and off on the multi-function display.
Air-recirculation mode is deactivated automatically to prevent the windows from misting at outside temperatures of less than approx. 41 °F (5 °C).
For information on adjusting automatic air-recirculation mode on the multi-function display:fPlease see the chapter “SETTING AIR CONDITIONING” on page 123.
Information
The recommended operating mode is automatic air-recirculation mode (default setting).
14_991_Turbo_21.book Seite 57 Mittwoch, 9. April 2014 2:19 14
Page 60 of 300
58 Air Conditioning
A- Set temperature left/right B - Set air quantity
Setting temperature
For personal comfort, the interior temperature can be adjusted individually for the driver’s and passenger’s side between 61 °F (16 °C) and 85 °F (29.5 °C). Recommendation: 72 °F (22 °C).
The selected temperature is shown on the display.
Increasing temperature
fPress button TEMP upwards. The preset temperature value is shown on the air-conditioning display.
Information
Pressing button AUTO/SYNC selects the preset temperature.
Information
The air-conditioning system always cools and heats the passenger compartment to the preset temperature at maximum cooling or heating temperature.Setting the temperature temporarily to a lower or higher value does not cool or heat the passenger compartment to the desired temperature more quickly.
Set air quantity
The selected air quantity is shown in a bar display above the button . The more bars that are displayed, the more air flows into the passenger compartment.
Increasing air quantity
fPress button upwards.
Reducing air quantity
fPress button downwards.
Pressing button AUTO/SYNC switches back to automatic mode.
If the air quantity was reduced so much that OFF appears on the air-conditioning display, the outside-air supply is interrupted and the air-conditioning compressor is switched off.
The windows can mist up if the air quantity setting is OFF.fOnly select air quantity setting OFF for short periods.fPress button upwards (increase air quantity).
Setting air distribution manually
fPress button . The air flows to the windshield and the side windows.fPress button .The air flows from the central and side vents. The air vents must be open.fPress button .The air flows to the footwell.
The indicator light on the button lights up.
Cancelling manual air distribution
fPress the relevant air distribution button again. The indicator light on the button goes out.orPress button AUTO/SYNC. Air quantity and distribution are controlled automatically and variations are compensated.
Air Shut-off Impairing VisionWARNINGh
14_991_Turbo_21.book Seite 58 Mittwoch, 9. April 2014 2:19 14
Page 62 of 300
60 Air Conditioning
Heated Rear Window/
Exterior Mirror Heating
Heated rear window/exterior mirror heating is ready for operation when the engine is running.
Switching on
fPress button .The indicator light on the button lights up.
Depending on the outside temperature, the heating switches off automatically after approx. 5 to 20 minutes.fThe heating can be switched back on by pressing the button again.
Switching off
fPress button .The indicator light on the button goes out.
If the charging condition of the battery is critical, the heated rear window/exterior mirror heating function is restricted initially and then switched off.
14_991_Turbo_21.book Seite 60 Mittwoch, 9. April 2014 2:19 14