lock PORSCHE CAYNNE 2010 1.G Owners Manual

Minor Repairs
325
Battery chargingAutomotive batteries loose their efficiency when
not in use. The charge available in your battery can
be measured with a battery hydrometer. We
recommend that the battery voltage be tested by
your Porsche dealer who has the appropriate
equipment.
If the car is not driven for prolonged periods, the
battery must be charged at least every 6 weeks.
A discharged battery allows rapid formation of sul-
fates, leading to premature deterioration of the
plates.
Danger!
Hydrogen gas generated by the battery
could cause an explosion, resulting in
serious personal injury or death.
fCharge battery in a well ventilated area.
fNever charge a frozen battery. It may explode
because of gas trapped in the ice. Allow a fro-
zen battery to thaw out first.
fIf you get electrolyte, which is an acid, in your
eyes or on your skin, immediately rinse with
cold water for several minutes and call a doc-tor.Note
Your authorized Porsche dealer will be pleased to
advise you about a suitable charger.
fAlways observe the instructions of the charger
manufacturer.
fWhen charging the battery, ensure adequate
ventilation.
1. Check the acid level of a low-maintenance
battery.
2. Connect charger to the jump starting points.
Only plug into the mains and switch the
charger on when it has been correctly
connected up.
3. Switch on the charger.
4. After charging, switch off and disconnect the
charger.
5. Check the acid level of a low-maintenance
battery.
After charging the battery After the battery is connected or the completely
discharged battery is charged, the PSM warning
light lights up on the instrument panel and a
message appears on the multi-purpose display of
the instrument panel to indicate a fault.
This fault can be remedied with a few simple
steps:
1. Start the engine.
To do this, turn the ignition key or the control
unit (on vehicles that have Porsche Entry &
Drive) to ignition lock position 2 twice.
2. Perform a few steering movements to the left
and to the right when vehicle is standing and
drive a short distance in a straight line until the
PSM warning light goes out and the message
is erased from the memory of the multi-
purpose display of the instrument panel.
3. If the warnings does not go out, then:
Drive carefully to the nearest authorized
Porsche dealer.
Have the fault remedied by an authorized
Porsche dealer.
10_Cayenne_21_KW17.book Seite 325 Donnerstag, 9. April 2009 3:33 15

328
Minor Repairs 6. Pull the headlight forward out of the fender by
approx. 4 inch (10 cm).
7. Press back the release tab of the plug D and
pull plug off.
8. Pull out headlight completely.
A - Cover
C - Socket wrench
D - PlugInstalling headlights1. Insert headlight in the guide rails, connect plug
D and then push the headlight fully into the
fender.
2. Push headlight to the rear and simultaneously
turn socket wrench C in the direction of the
arrow.
The headlight locking device must perceptibly
and audibly engage.
3. Check whether the headlight is seated
securely.4. Remove socket wrench C and replace in tool
kit.
5. Fit cover A and fold it down.
6. Close lid.
10_Cayenne_21_KW17.book Seite 328 Donnerstag, 9. April 2009 3:33 15

Minor Repairs
329
Changing bulbs on Halogen headlightsChanging bulb for low beam/high beam
1. Remove headlight.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
LIGHTS” on Page 327.
2. Press down both release tabs A and remove
cover.3. Turn bulb socket B counter-clockwise and
remove. 4. Remove defective bulb and replace.
5. Insert bulb socket and turn in clockwise direc-
tion.
Make sure that the bulb is installed in the
correct position.
6. Fit cover on headlight.
Both release tabs must be fully engaged.
7. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
8. Check operation of bulbs.
10_Cayenne_21_KW17.book Seite 329 Donnerstag, 9. April 2009 3:33 15

330
Minor Repairs Changing bulb for additional high beam
fA Bi-Xenon headlight is used to demonstrate
the procedure for changing the bulb for the
additional high beam.
Please see the chapter “CHANGING BULB FOR
ADDITIONAL HIGH BEAM” on Page 331.
Changing bulbs on Bi-Xenon headlights
with cornering lightChanging gas discharge lamp for low beam/
high beam/dynamic cornering light
1. Remove headlight.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
LIGHTS” on Page 327.
2. Press down both release tabs A and remove
cover.3. Turn gas discharge lamp counter-clockwise
and remove.
10_Cayenne_21_KW17.book Seite 330 Donnerstag, 9. April 2009 3:33 15

Minor Repairs
331
4. Press the release tab on the plug and pull plug
off.
5. Connect plug to new gas discharge lamp.
6. Insert gas discharge lamp and turn in clock-
wise direction. Make sure that the bulb is
installed in the correct position.
7. Fit cover on headlight. Both release tabs must
be fully engaged.
8. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
9. Check operation of bulbs.Changing bulb for additional high beam
1. Remove headlight.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
LIGHTS” on Page 327.
2. Press down both release tabs A and remove
cover.3. Turn bulb socket B counter-clockwise and
remove.
10_Cayenne_21_KW17.book Seite 331 Donnerstag, 9. April 2009 3:33 15

332
Minor Repairs 4. Remove defective bulb and replace.
5. Insert bulb socket and turn in clockwise direc-
tion. Make sure that the bulb is installed in the
correct position.
6. Fit cover on headlight. Both release tabs must
be fully engaged.
7. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
8. Check operation of bulbs.Changing lamp for static cornering light
1. Remove headlight.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
LIGHTS” on Page 327.
2. Press down both release tabs A and remove
cover.3. Turn bulb socket B counter-clockwise and
remove.
10_Cayenne_21_KW17.book Seite 332 Donnerstag, 9. April 2009 3:33 15

334
Minor Repairs Replacing side marker light bulb
Cayenne, Cayenne S, Cayenne S
Transsyberia
4. Pull bulb socket out of the bulb housing.5. Remove the defective bulb from the socket
and replace.
When inserting the socket in the bulb housing,
make sure that the socket has engaged fully.Changing turn signal bulb
Cayenne, Cayenne S, Cayenne S
Transsyberia
1. Turn socket counter-clockwise and remove.
2. Replace the defective bulb (bayonet fitting).
3. Insert socket and turn in clockwise direction.
Make sure that the bulb is installed in the
correct position.
10_Cayenne_21_KW17.book Seite 334 Donnerstag, 9. April 2009 3:33 15

Minor Repairs
335
Installing bulb housing
Cayenne, Cayenne S, Cayenne S
Transsyberia
1. Insert the bulb housing in the front apron. Make
sure that the two tabs are inserted correctly in
the openings. Push light fully into the front
apron until you hear and feel it engage.
2. Check operation of lights.
3. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
Changing bulb for turn signal
Cayenne GTS1. Remove headlight.
For information on removing headlights:
Please see the chapter “REMOVING HEAD-
LIGHTS” on Page 327.
2. Turn socket counter-clockwise and remove.
3. Replace the defective bulb (bayonet fitting).4. Insert socket and turn in clockwise direction.
Make sure that the bulb is installed in the
correct position.
5. Check operation of bulb.
6. Install headlight.
For information on installing headlights:
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
10_Cayenne_21_KW17.book Seite 335 Donnerstag, 9. April 2009 3:33 15

Minor Repairs
341
Halogen headlights2. Push lever B down to the stop.
Xenon headlight3. Turn spindle C in clockwise direction to the
stop using a crosshead screwdriver.
4. Fit cover on headlight.
Both release tabs A must be fully engaged.
5. Install headlight.
Please see the chapter “INSTALLING HEAD-
LIGHTS” on Page 328.
6. Reposition the other headlight.
10_Cayenne_21_KW17.book Seite 341 Donnerstag, 9. April 2009 3:33 15

344
Minor Repairs Screwing in front towing hook
1. Carefully lever out the appropriate plastic
cover A in the bumper with the screwdriver.
Place cover in the vehicle.2. Screw in towing hook B as far as the stop (left-
hand thread) and tighten hand-tight.Fitting plastic cover at front
First engage the upper locking tabs of the plastic
cover, and then press in the bottom tabs and side
tab uniformly until the tabs have engaged fully.
10_Cayenne_21_KW17.book Seite 344 Donnerstag, 9. April 2009 3:33 15