Ram 2500 2019 Owner's Manual

STARTING AND OPERATING 349
13.Establish "no people" zones: Make your intentions clear.
Be sure that everyone in the immediate vicinity
surrounding the winching operation is completely aware
of your intentions before you pull. Declare where the
spectators should not stand - never behind or in front of
the vehicle and never near the synthetic rope or snatch
block. Your situation may have other "no people" zones.
No People Zones 14. Begin winching. With the winching vehicles engine on
and light tension already on the synthetic rope, begin
winching slowly and steadily. Be sure that the rope is
winding evenly and tightly around the spooling drum.
For additional assistance, the winched vehicle can be
slowly driven while being pulled by the winch. Continue
pulling until the vehicle is on stable ground. If you are
able to drive the vehicle, the winching operation is
complete.
Using The Remote Control
5

350 STARTING AND OPERATING
NOTE:•Avoid overheating the winch motor. For extendedwinching, stop at reasonable intervals to allow the
winch motor to cool down.
•What to look for under load: The synthetic rope must always spool onto the drum as indicated by the drum
rotation decal on the winch. As you power-in, make
sure the synthetic rope winds evenly and tightly on the
drum. This prevents the outer rope wraps from
drawing into the inner wraps, binding and damaging
the synthetic rope. Avoid shock loads by using the
control switch intermittently to take up rope slack.
Shock loads can momentarily far exceed the winch and
synthetic rope ratings. During side pulls the synthetic
rope tends to stack up at one end of the drum. This
stack can become large enough to cause serious
damage to the winch. So, line up pulls as straight ahead
as possible and stop winching if the synthetic rope
comes close to the tie rods or mounting plate. To fix an
uneven stack, spool out that section of the rope and
reposition it to the opposite end of the drum, which will
free up space for continued winching. 15. Secure vehicle. Once recovery of the vehicle is complete,
be sure to secure the vehicle's brakes and shift the trans -
mission to PARK. Release tension in the synthetic rope.
16. Disconnect the synthetic rope, and disconnect from the anchor.
17. Rewind the synthetic rope. The person handling the synthetic rope should walk the rope in and not let it slide
through the hand, control the winch at all times.
Rewinding The Synthetic Rope

STARTING AND OPERATING 351
NOTE:
How to spool under no load: Arrange the remote control
lead so it cannot be caught in the winch. Arrange the
synthetic rope so it will not kink or tangle when spooled. Be
sure any synthetic rope already on the spooling drum is
wound tightly and evenly layered. Tighten and straighten
the layer if necessary. Keep the synthetic rope under light
tension and spool the rope back and onto the winch drum in
even layers. Stop frequently to tighten and straighten the
layers as necessary. Repeat this process until the winch hook
is the same distance as the full length of the remote control
from the winch. Pinch the hook between your thumb and
forefinger and attach the hook strap. Hold the hook strap
between the thumb and forefinger to keep tension on the
synthetic rope. Walk the synthetic rope towards the fairlead,
carefully spooling in the remaining rope. By pulsing the
remote control switch. 18. Store the hook on the most outboard loop of the hawse
fairlead.
Hook In Stored Position
19. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and
dry place. Winching operations are now complete. Put
the cap on the solenoid plug-in.
NOTE:
Always store the remote control in a protected, clean, dry
area.
WARNING!
To prevent serious injury, NEVER put your fingers
inside the hook area as you are powering-in.
5

352 STARTING AND OPERATING
Rigging Techniques
Various winching situations will require application of other
winching techniques. These could range from too little
distance to achieve maximum pull using straight line
rigging, simply increasing pulling power, or maintaining a
straight-line pulling situation. You will have to assess what
technique is correct for your situation. Think "safety" at all
times.How To Change The Pulling Direction
Change Pulling Directions
All winching operations should have a straight line from the
winch to the object being pulled. This minimizes the
synthetic rope collecting on one side of the drum affecting
pulling efficiency and damaging synthetic rope. A snatch
block, secured to a point directly in front of the vehicle will
enable you to change your pulling direction while still
allowing the synthetic rope to be at 90° to wind properly onto
the spooling drum.

STARTING AND OPERATING 353
Increasing Pulling Power
In some cases, you may find yourself needing more pulling
power. The use of snatch blocks increases mechanical advan-
tage and that increases your pulling power.
Double Line
Wire Rope Routing Because pulling power decreases with the number of layers
of synthetic rope on the winch drum, you can use a snatch
block to double line out more rope. This decreases the
number of layers of synthetic rope on the drum, and
increases pulling power. Start by feeding out enough
synthetic rope to free the winch hook. Attach the hook to
your vehicle's frame/tow hook and run the rope through a
snatch block. Disengage the clutch and, using the snatch
block, pull out enough synthetic rope to reach your anchor
point. Do not attach the hook to the mounting kit. Secure to
the anchor point with a tree trunk protector or choker chain.
Attach the clevis/shackle. Attach the shackle to the two ends
of the strap/chain, being careful not to over tighten (tighten
and back-off 1/2 turn).
5

354 STARTING AND OPERATING
FUEL SAVER TECHNOLOGY — IF EQUIPPED
This feature offers improved fuel economy by shutting off
four of the engine's eight cylinders during light load and
cruise conditions. The system is automatic with no driver
inputs or additional driving skills required.
NOTE:
This system may take some time to return to full function-
ality after a battery disconnect.
SPEED CONTROL
When engaged, the Speed Control takes over accelerator
operations at speeds greater than 20 mph (32 km/h).
The Speed Control buttons are located on the right side of the
steering wheel. Speed Control Buttons
NOTE:
In order to ensure proper operation, the Speed Control
System has been designed to shut down if multiple speed
control functions are operated at the same time. If this
occurs, the Speed Control System can be reactivated by
pushing the Speed Control On/Off button and resetting the
desired vehicle set speed.
1 — On/Off Button 3 — SET (-)
2 — RES (+) 4 — CANCEL

STARTING AND OPERATING 355
To Activate
Push the On/Off button to activate the Speed Control. The
cruise indicator light in the instrument cluster display will
illuminate. To turn the system off, push the On/Off button a
second time. The cruise indicator light will turn off. The
system should be turned off when not in use.
To Set A Desired Speed
Turn the Speed Control on. When the vehicle has reached the
desired speed, push the SET (-) button and release. Release
the accelerator and the vehicle will operate at the selected
speed.
NOTE:
The vehicle should be traveling at a steady speed and on
level ground before pushing the SET (-) button.
To Vary The Speed Setting
To Increase Speed
When the Speed Control is set, you can increase speed by
pushing the RES (+) button.
The driver’s preferred units can be selected through the
instrument panel settings if equipped. Refer to “Getting To
Know Your Instrument Panel” for more information. The
speed decrement shown is dependant on the chosen speed
unit of U.S. (mph) or Metric (km/h):
U.S. Speed (mph)
• Pushing the RES (+) button once will result in a 1 mph increase in set speed. Each subsequent tap of the button
results in an increase of 1 mph.
• If the button is continually pushed, the set speed will continue to increase until the button is released, then the
new set speed will be established.
WARNING!
Leaving the Speed Control system on when not in use is
dangerous. You could accidentally set the system or
cause it to go faster than you want. You could lose
control and have an accident. Always leave the system
off when you are not using it.
5

356 STARTING AND OPERATING
Metric Speed (km/h)
• Pushing the RES (+) button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button
results in an increase of 1 km/h.
• If the button is continually pushed, the set speed will continue to increase until the button is released, then the
new set speed will be established.
To Decrease Speed
When the Speed Control is set, you can decrease speed by
pushing the SET (-) button.
The driver’s preferred units can be selected through the
instrument panel settings if equipped. Refer to “Getting To
Know Your Instrument Panel” for more information. The
speed decrement shown is dependant on the chosen speed
unit of U.S. (mph) or Metric (km/h):
U.S. Speed (mph)
• Pushing the SET (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button
results in a decrease of 1 mph.
• If the button is continually pushed, the set speed will continue to decrease until the button is released, then the
new set speed will be established. Metric Speed (km/h)

• Pushing the SET (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button
results in a decrease of 1 km/h.
• If the button is continually pushed, the set speed will continue to decrease until the button is released, then the
new set speed will be established.
To Accelerate For Passing
Press the accelerator as you would normally. When the pedal
is released, the vehicle will return to the set speed.
Using Speed Control On Hills
The transmission may downshift on hills to maintain the
vehicle set speed.
NOTE:
The Speed Control system maintains speed up and down
hills. A slight speed change on moderate hills is normal.

STARTING AND OPERATING 357
On steep hills, a greater speed loss or gain may occur so it
may be preferable to drive without Speed Control.
To Resume Speed
To resume a previously set speed, push the RES (+) button
and release. Resume can be used at any speed above 20 mph
(32 km/h).
To Deactivate
A soft tap on the brake pedal, pushing the CANCEL button,
or normal brake pressure while slowing the vehicle will
deactivate the Speed Control without erasing the set speed
from memory.
Pushing the On/Off button, or returning the ignition to OFF,
erases the set speed from memory.
ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED
Adaptive Cruise Control (ACC) increases the driving conve-
nience provided by cruise control while traveling on high -
ways and major roadways. However, it is not a safety system
and not designed to prevent collisions. Speed Control func-
tion performs differently. Please refer to the proper section
within this chapter.
ACC will allow you to keep cruise control engaged in light
to moderate traffic conditions without the constant need to
reset your cruise control. ACC utilizes a radar sensor and a
forward facing camera designed to detect a vehicle directly
ahead of you.
NOTE:
• If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed.
• If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or accelerate (not to exceed the original set
speed) automatically to maintain a preset following
distance, while matching the speed of the vehicle ahead.
WARNING!
Speed Control can be dangerous where the system
cannot maintain a constant speed. Your vehicle could go
too fast for the conditions, and you could lose control
and have an accident. Do not use Speed Control in heavy
traffic or on roads that are winding, icy, snow-covered or
slippery.
5

358 STARTING AND OPERATING
(Continued)
The Cruise Control system has two control modes:
• Adaptive Cruise Control mode for maintaining an appro-
priate distance between vehicles.
• Normal (Fixed Speed) Cruise Control mode for cruising at a constant preset speed. For additional information, refer
to “Normal (Fixed Speed) Cruise Control Mode” in this
section.
NOTE:
Normal (Fixed Speed) Cruise Control will not react to
preceding vehicles. Always be aware of the mode selected.
You can change the mode by using the Cruise Control
buttons. The two control modes function differently. Always
confirm which mode is selected.WARNING!

• Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is
always the driver’s responsibility to be attentive of road,
traffic, and weather conditions, vehicle speed, distance
to the vehicle ahead; and, most importantly, brake oper -
ation to ensure safe operation of the vehicle under all
road conditions. Your complete attention is always
required while driving to maintain safe control of your
vehicle. Failure to follow these warnings can result in a
collision and death or serious personal injury.

• The ACC system: • Does not react to pedestrians, oncoming vehicles,and stationary objects (e.g., a stopped vehicle in a
traffic jam or a disabled vehicle).
• Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight
distance conditions.
• Does not always fully recognize complex driving conditions, which can result in wrong or missing
distance warnings.