keyless Ram 4500 Chassis Cab 2018 Quick Reference Guide

Automatic High Beam — If
Equipped
The Automatic High Beam system provides
increased forward lighting at night by automat-
ing high beam control through the use of a
digital camera mounted above the inside rear-
view mirror. This camera detects vehicle spe-
cific light and automatically switches from high
beams to low beams until the approaching
vehicle is out of view. This feature is program-
mable through the Uconnect system.
NOTE:
For further information, and applicable warn-
ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).
Parkview Rear Back-Up Camera —
If Equipped
You can see an on-screen image of the rear of
your vehicle whenever the transmission is
shifted into REVERSE. The ParkView Rear
Back-Up Camera image will be displayed on the
Uconnect Display, located on the center stack
of the instrument panel.
For further information, and applicable warn-
ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).
NOTE:
For further information, please refer to the Ram
Body Builders Guide by accessing
www.rambodybuilder.com and choosing the ap-
propriate links.
Introduction To Keyless
Enter-N-Go
The Keyless Enter-N-Go — Passive Entry sys-
tem is an enhancement to the vehicles key fob.
This feature allows you to lock and unlock the
vehicle’s door(s) without having to push the key
fob lock or unlock buttons as well as starting
and stopping the vehicle with the push of a
button.
To Lock The Vehicle’s Doors
With a valid Keyless Enter-N-Go key fob within
5 ft (1.5 m) of the driver or passenger front door
handles, push door handle lock button to lock
all doors.
Do NOT grab the door handle, when pushing
the door handle lock button. This could unlock
the door(s).
LIGHTSPARKVIEW KEYLESS ENTER-N-GO —
PASSIVE ENTRY

NOTE:
• After pushing the door handle lock button,you must wait two seconds before you can
lock or unlock the doors, using either Passive
Entry door handle. This is done to allow you
to check if the vehicle is locked by pulling
the door handle without the vehicle reacting
and unlocking.
• The Passive Entry system will not operate if the key fob battery is dead.
The vehicle doors can also be locked by using
the key fob lock button or the lock button
located on the vehicles interior door panel.To Unlock From The Driver Or
Passenger Side
With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of
the driver or passenger side door handle, grab
either front door handle to unlock the door
automatically.
Push The Button To Lock
Do NOT Grab The Handle When Locking
Grab The Door Handle To Unlock

For further information, and applicable warn-
ings and cautions, please refer to the Owner’s
Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).Keyless Enter-N-Go — Ignition
Starting
With a valid Keyless Enter-N-Go key fob inside
the vehicle:
1. Shift the transmission into PARK (P).2. While pressing the brake pedal, push the
ENGINE START/STOP button once. If the
engine fails to start, the starter will disen-
gage automatically after 10 seconds.
3. To stop the cranking of the engine prior to the engine starting, push the button again.
NOTE:
In case the ignition switch does not change with
the push of a button, the key fob may have a low
or dead battery. In this situation, a back up
method can be used to operate the ignition
switch. Put the nose side of the key fob (side
opposite of the emergency key) against the
ENGINE START/STOP button and push to op-
erate the ignition button.
Start/Stop Button
KEYLESS ENTER-N-GO —
IGNITION