wiring Ram 5500 Chassis Cab 2017 User Guide

CAUTION!
•Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
• Always use the correct bulb size and type for replace-
ment. An incorrect bulb size or type may overheat
and cause damage to the lamp, the bulb socket, or the
lamp wiring.
NOTE: There are access covers over both headlamp bulb
access holes in the quad front lamp unit housing (if
equipped). These covers MUST be reinstalled after the bulb
has been replaced.
Fog Lamps — If Equipped
1. Reach under and behind the front bumper to access the back of the front fog lamp housing.
2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb.
3. Rotate the bulb counterclockwise ¼ turn to unlock the bulb from the housing.
4. Pull the bulb straight out from the housing.
CAUTION!
Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result.
Center High-Mounted Stoplamp (CHMSL) With
Cargo Lamp
1. Remove the two screws holding the housing/lens to the body as shown.
CHMSL Mounting Screw Locations
496 MAINTAINING YOUR VEHICLE

2. Separate the connector holding the housing and wiringharness to the body.
3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing.
4. Pull the desired bulb straight from the socket.
CAUTION!
Do not contaminate the bulb glass by touching it with
your fingers or by allowing it to contact other oily
surfaces. Shortened bulb life will result. • Outside Bulbs: Cargo Lamps
• Inside Bulb: Center High-Mounted Stop Lamp
5. Reverse the procedure for installation of bulbs and housing.
CHMSL Connector Location
CHMSL Bulb And Socket
7
MAINTAINING YOUR VEHICLE 497

Aging (Life Of Tires)..................... .383
Air Pressure ........................ .371, 376
Chains ............................... .385
Compact Spare ......................... .381
Dual .......................... .387, 427, 434
General Information ...................376, 380
High Speed ............................ .378
Inflation Pressures ....................... .377
Life Of Tires ........................... .383
Load Capacity ...................... .371, 373
Pressure Monitor System (TPMS) .............389
Pressure Warning Light ....................212
Quality Grading ........................ .388
Radial ............................... .378
Replacement ........................... .384
Rotation .............................. .386
Safety ............................ .365, 376
Sizes ................................ .367
Snow Tires ............................ .379
Spare Tire ...................... .380, 381, 382
Spinning .............................. .382
Tread Wear Indicators .....................383
Wheel Nut Torque ....................... .433
Tire Safety Information ...................... .365
Tongue Weight/Trailer Weight .................408Torque Converter Clutch
.....................335
Tow Hooks, Emergency ..................... .440
Towing ............................. .403, 442
Disabled Vehicle ........................ .442
Guide ................................ .407
Recreational ........................... .418
Weight ............................... .407
Towing Vehicle Behind A Motorhome ............418
Traction ................................ .347
T

raction Control .......................... .357
Trailer Sway Control (TSC) ....................362
Trailer Towing ............................ .403
Cooling System Tips ..................... .415
Hitches ............................... .407
Minimum Requirements ....................408
Mirrors ................................113
Trailer And Tongue Weight ..................408
Wiring ............................... .414
Trailer Towing Guide ....................... .407
Trailer Weight ............................ .407
Transfer Case ............................ .478
Electronically Shifted ..................... .342
Fluid ................................ .502
Transmission ............................. .478
Automatic ......................... .327, 478
528 INDEX

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.