turn signal Ram ProMaster 2015 User Guide

Mute/Pause
Pushing this button mutes the sound. The display will
switch betweenMUTE ONand the previous display (3
seconds).
Pushing the button again restores the audio without
changing the original volume setting. The display will
show MUTE OFF for three seconds, and then return to
the previous display mode.
When the
or, Audio, 1, 2, 3, 4, 5, 6, BAND/AS
buttons and SRC are pushed in Mute/Pausedmode,
these will be implemented and the audio will be
restored without changing the original volume.
Turn the ROTARY knob to restore the audio and change
the volume to the level selected. The display will show
the settings described in the volume function.
The other buttons should be implemented when pushed,
but the radio will remain in MUTE ONmode. Storing Stations In Memory
Push and hold the memory buttons (1 through 6) for
more than two seconds to associate the tuned station
with the pushed button. The display will show a message
in
MEMO 2 format for three seconds to confirm that the
station has been tuned in. The CH signal is then activated
and the display will show the preset number and station
frequency for three seconds 2 106.9. The display will
then return to the previous view.
Accessing Preset Stations
When the preset buttons (1 through 6) are pushed for less
than two seconds the radio will tune in to the station
associated with that particular memory location. The
display shows the preset number and frequency of the
associated station for three seconds. The display will then
return to the previous view.
158 UNDERSTANDING YOUR INSTRUMENT PANEL

Retuning the band: When the BAND/AS button is
pushed for less than two seconds, the radio will alternate
between bands in the sequence: FM1
FM2FM3
AM1AM2FM1. While changing bands from
the FM3 band to
AM1, the display will show AM
for two seconds and when changing from the AM2
band to
FM1, the display will show FMfor two
seconds.
The display will then show the selected band and fre-
quency in the format F1 106.9for two seconds and then
return to the previous view.
Presetting stations with a strong signal: when the
BAND/AS button is pushed for more than two seconds,
the radio will search for the 6 best stations and automati-
cally store them in the 6 memory positions of the current
band. During the search, the display will indicate FM
AST orAM AST, depending on the band selected. To
record the stations that are found, these are sorted in
ascending order of frequency and the first one is stored in memory position 1, and so on, until positions 1-6 are all
in use. If fewer than 6 stations are found, the unused
channels will be allocated to the 107.9 MHz frequency for
FM and AM 1710 KHz for the AM band. At the end of the
search process, the radio tunes in to the first preset
position and the display will indicate the associated
preset number (1) and the station frequency for three
seconds. The display will then return to the previous
view.
Setup Menu
You can use the Setup menu to change the various factory
settings to suit your own preferences.
Push MENU to activate the Maximum Volume function.
Repeatedly pushing this button will activate the other
functions in the following sequence: Maximum Volume
(MVOL)
Auto Switch (AUTO)Beep (BEEP)
Set ClockMaximum Volume (MVOL). If this
button or the button for adjusting the selected function 4
UNDERSTANDING YOUR INSTRUMENT PANEL 159

2. Installing some form of aftermarket window tintingthat affects radio wave signals.
3. Snow or ice around the wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM sensors.
NOTE: Your vehicle is equipped with a regular size
spare wheel.
1. The spare tire has a tire pressure monitoring sensor, but it is not monitored until it is mounted in place of
any of the existing four road tires.
2. If you install the spare tire in place of a road tire that has a pressure below the low-pressure warning limit,
upon the next ignition key cycle, a chime will sound
and the Tire Pressure Monitoring Telltale Light will
turn ON due to the low tire condition. Then, after driving the vehicle for up to 20 minutes above 15mph
(24km/h), the system will recognize the new sensor, so
turn off the telltale.
3. If a spare tire not equipped with tire pressure moni- toring sensor is used, then the Tire Pressure Monitor-
ing Telltale Light will turn ON, flashing for 75 seconds
and then remaining solid for each subsequent ignition
key cycle.
NOTE: For a correct Tire Pressure Monitoring behavior,
please wait for about 20 minutes in key-off during each
tire substitution.
General Information
This device complies with Part 15 of the FCC rules and
RSS-210 of Industry Canada. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
5
STARTING AND OPERATING 261

CAUTION!
If the trailer weighs more than 1,000 lbs (454 kg)
loaded, it should have its own brakes and they
should be of adequate capacity. Failure to do this
could lead to accelerated brake lining wear, higher
brake pedal effort, and longer stopping distances.
Towing Requirements — Trailer Lights And Wiring
Whenever you pull a trailer, regardless of the trailer size,
stoplights and turn signals on the trailer are required for
motoring safety.
The Trailer Tow Package may include a four- and seven-
pin wiring harness. Use a factory approved trailer har-
ness and connector.NOTE:Do not cut or splice wiring into the vehicles
wiring harness.
Trailer Electrical Connector Location
1 — Four-Pin Connector Location
2 — Seven-Pin Connector Location
280 STARTING AND OPERATING

HAZARD WARNING FLASHERS
The Hazard Warning flasher switch is located on the
instrument panel below the climate controls.Push the switch to turn on the Hazard Warning
flasher. When the switch is activated, all direc-
tional turn signals will flash on and off to warn oncoming
traffic of an emergency. Push the switch a second time to
turn off the Hazard Warning flashers.
This is an emergency warning system and it should not
be used when the vehicle is in motion. Use it when your
vehicle is disabled and it is creating a safety hazard for
other motorists.
When you must leave the vehicle to seek assistance, the
Hazard Warning flashers will continue to operate even
though the ignition is placed in the OFF position.
NOTE: With extended use the Hazard Warning flashers
may wear down your battery.
IF YOUR ENGINE OVERHEATS
In any of the following situations, you can reduce the
potential for overheating by taking the appropriate action.
• On the highways — slow down.
• In city traffic — while stopped, place the transmission
in NEUTRAL, but do not increase the engine idle
speed while maintaining the motion of the vehicle
with the brakes.
NOTE: There are steps that you can take to slow down
an impending overheat condition:
• If your air conditioner (A/C) is on, turn it off. The A/C
system adds heat to the engine cooling system and
turning the A/C off can help remove this heat.
• You can also turn the temperature control to maximum
heat, the mode control to floor and the blower control
to high. This allows the heater core to act as a
supplement to the radiator and aids in removing heat
from the engine cooling system.
6
WHAT TO DO IN EMERGENCIES 287

▫Appearance Care And Protection From
Corrosion .......................... .355
▫ Cleaning The Instrument Panel Cupholders . .361
 FUSES ............................. .362
▫ Underhood Fuses ..................... .363
▫ Interior Fuses ........................370
▫ Right Central Pillar Fuses ................374
 VEHICLE STORAGE ....................375
 REPLACEMENT BULBS .................376
 BULB REPLACEMENT ..................378
▫ Headlamps Low Beam And High beam .....378
▫ Front Turn Signal/Parking Lamps .........379▫
Daytime Running Lamp (DRL)/Front Side Marker
Lamp ............................. .379
▫ Front Fog Lamps ..................... .380
▫ Front, Rear Roof Lamps .................381
▫ Rear Tail, Stop, Backup, Turn Signal And Rear
Side Marker Lamps ....................381
 FLUID CAPACITIES ....................382
 FLUIDS, LUBRICANTS, AND GENUINE
PARTS ............................. .383
▫ Engine ............................ .383
▫ Chassis ............................385
328 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
Front Low and High Beam Headlamp H7LL
Front Park/Turn Signal Lamps 7444NA
Daytime Running Lamps (If Equipped) 7440
Front Side Marker Lamps WY5W
Rear Tail/Stop Lamps 7443
Rear Turn Signal Lamps 7440NA
Rear Backup Lamps 921
Rear Side Marker Lamps W3W
Front Fog Lamps H11
License Plate Lamps C5W
Front Roof Lamps WY5W
Rear Roof Lamps W3W
NOTE:
•Numbers refer to commercial bulb types that can be purchased from your authorized dealer.
•If a bulb needs to be replaced, visit your authorized dealer.
7
MAINTAINING YOUR VEHICLE 377

16. Carefully reinstall screw (1) on lower headlamp fillerpanel.
17. Carefully reinstall screws (2) on upper headlamp filler panel.
Front Turn Signal/Parking Lamps
NOTE: Passenger side headlamp must be removed for
bulb replacement, for driver side headlamp go to step 6
through step 7.
1. Remove screw (1) on lower headlamp filler panel.
2. Remove screws (2) on upper headlamp filler panel.
3. Remove upper screw (1) from headlamp housing.
4. Remove lower screws (2) from headlamp housing.
5. Pull Headlamp forward.
6. Rotate the bulb counter clockwise and remove. 7. Install the bulb into socket, and rotate bulb/socket
clockwise into lamp locking it in place.
8. Carefully reinstall headlamp in the same position on the vehicle, so as not to affect headlamp aiming.
9. Install upper screw (1) on headlamp housing.
10. Install lower screws (2) on headlamp housing.
11. Carefully reinstall screw (1) on lower headlamp filler panel.
12. Carefully reinstall screws (2) on upper headlamp filler panel.
Daytime Running Lamp (DRL)/Front Side Marker
Lamp
NOTE: Passenger side headlamp must be removed for
bulb replacement, for driver side headlamp go to step 6
through step 8.
7
MAINTAINING YOUR VEHICLE 379

Front, Rear Roof Lamps
1. Remove two screw and remove the lamp assembly.
2. Remove the socket bulb by turning counterclockwise.
3. Remove bulb and replace as needed.
4. Reinstall the bulb socket and rotate clockwise to lockin place.
5. Reinstall lamp.
Rear Tail, Stop, Backup, Turn Signal And Rear
Side Marker Lamps
1. Open rear doors.
2. Remove the two screws and remove the tail lamp.
3. Remove the tail/stop, turn signal, backup and rear side marker bulb/socket by rotating counter-
clockwise.
4. Remove the bulb and replace as needed.
5. Reinstall bulb/socket and rotate clockwise to lock in place.
6. Reinstall lamp.
7
MAINTAINING YOUR VEHICLE 381

Engine Oil Disposal.....................337
Flashers Hazard Warning ........................287
Turn Signal ........................ .67, 128
Flooded Engine Starting ....................201
Fluid Capacities ..........................382
Fluid Leaks ..............................68
Fluid Level Checks Automatic Transmission ..................354
Brake ............................... .352
Cooling System ........................ .346
Power Steering ........................ .218
Fluids, Lubricants And Genuine Parts ...........383
Fog Lights ............................93, 128
Four-Way Hazard Flasher ...................287
Freeing A Stuck Vehicle .....................323
Fuel .................................. .262
Adding ............................. .266
Additives ............................ .264Clean Air
............................ .262
Ethanol ............................. .263
Filler Cap (Gas Cap) .....................266
Gasoline ............................. .262
Gauge ...............................128
Light ............................... .128
Materials Added ........................264
Methanol ............................ .263
Octane Rating ..................... .262, 383
Requirements .......................262, 382
Tank Capacity ..........................382
Fueling ............................... .266
Fuses ................................. .362
Gas Cap (Fuel Filler Cap) .............266, 268, 330
Gasoline, Clean Air ........................262
Gasoline (Fuel) .......................... .262
Gasoline, Reformulated .....................262
10
INDEX 411