display Ram ProMaster 2017 Owner's Guide

•Language
• Buzzer Volume
• Seat Belt Buzzer (*)
• (*) just available after SBR disable made by CHR
Service
• Service (Diesel Only)
• DRL - Daytime Running Lights (if equipped)
• Exit menu
NOTE:
• If equipped with Uconnect 5.0 radio, some customer
programmable features will display in the Uconnect
5.0 system. Refer to the radio supplement for further
Uconnect 5.0 information.
• The clock setting and Uconnect 5.0 clock setting pro-
cedure can be done through the radio or the Instru-
ment Cluster Display.
Selecting An Option Of The Main Menu Without Submenu
1. Briefly push and release the MODEbutton to select the
main menu option to set. 2. Push and release the
UPorDOWNarrow
button (by single pushes) to select the new setting.
3. Briefly push and release the MODEbutton to store the
new setting and go back to the main menu option
previously selected.
Selecting An Option Of The Main Menu With Submenu
1. Briefly push and release the MODEbutton to display
the first submenu option.
2. Push and release the UP
orDOWNarrow
button (by single pushes) to scroll through all the
submenu options.
3. Briefly push and release the MODEbutton to select the
displayed submenu option and to open the relevant
setup menu.
4. Push and release the UP
orDOWNarrow
button (by single pushes) to select the new setting for
this submenu option.
5. Briefly push and release the MODEbutton to store the
new setting and go back to the previously selected
submenu option.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 123

6. Push and release and hold theMODEbutton to return
to the main menu (short hold) or the main screen (longer
hold).
Change Engine Oil Indicator System
Change Engine Oil
Your vehicle is equipped with an engine oil change indi-
cator system. The “Change Engine Oil” message will
display in the Instrument Cluster Display. The engine oil
change indicator system is duty cycle based, which means
the engine oil change interval may fluctuate, dependent
upon your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN position.
To turn off the message temporarily, push and release the
MENU button. To reset the oil change indicator system
(after performing the scheduled maintenance), refer to the
following procedure.
1. Turn the ignition switch to the ON position (do not start the engine).
2. Fully push the accelerator pedal slowly, three times, within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position. NOTE:
If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.
Trip Computer
The Trip Computer is located in the instrument cluster. It
features a driver-interactive display (displays information
such as trip information, range, fuel consumption, average
speed, and travel time).
Trip Button
The TRIP button, located on the right steering column
stalk, can be used to display and to reset the previously
described values.
• A short button push displays the different values.
• A long button push resets the system and then starts a
new trip.
New Trip
To reset:
• Push and hold the TRIPbutton to reset the system
manually.
124 UNDERSTANDING YOUR INSTRUMENT PANEL

•When the “Trip distance” reaches 99999.9 miles or
kilometers or when the “Travel time” reaches 999.59 (999
hours and 59 minutes), the system is reset automatically.
• Disconnecting/Reconnecting the battery resets the sys-
tem.
NOTE: If the reset operation occurs in the presence of the
screens concerning Trip A or Trip B, only the information
associated with Trip A or Trip B functions will be reset.
Start Of Trip Procedure
With the ignition on, push and hold the TRIPbutton for
over 2 seconds to reset trip information.
Exit Trip
To exit the Trip function, wait until all the values have been
displayed or hold the MENUbutton for longer than one
second.
Briefly push and release the MENUbutton to go back to
the menu screen or push and hold the MENU(approxi-
mately one second) to go back to the main screen without
storing settings.
Trip Functions
Both trip functions are resettable (reset — start of new trip).
“Trip A” can be used to display the figures relating to:
• Trip Distance A
• Average Fuel Consumption
• Average Speed A
• Travel Time A (Driving Time)
“Trip B” can be used to display the figures relating to:
• Trip Distance B
• Average Fuel Consumption
• Average Speed B
• Travel Time B (Driving Time)
“Current Trip” can be used to display the figures relating
to:
NOTE: “Trip B” functions may be excluded (see “Trip B
Data”). “Range” and “Instantaneous Fuel Consumption”
cannot be reset.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 125

Values Displayed
Range
This indicates the distance which may be traveled with the
fuel remaining in the tank, assuming that driving condi-
tions will not change. The message “----” will appear on the
display in the following cases:
•Distance less than 30 miles (or 50 km).
• The vehicle is parked for a long time with the engine
running.
NOTE: The range depends on several factors: driving
style, type of route (freeway, residential, mountain roads,
etc.), and conditions of use of the vehicle (load, tire
pressure, etc.). Trip planning must take into account the
above notes.
Distance Traveled
This value shows the distance covered since the last reset.
Average Fuel Economy
This value shows the approximate average fuel consump-
tion since the last reset.
Instantaneous Fuel Economy
This indicates the fuel consumption. The value is con-
stantly updated. The message “----” will appear on the
display if the vehicle is parked with the engine running.
Average Speed
This value shows the vehicle’s average speed as a function
of the overall time elapsed since the last reset.
Travel Time
This value shows the time elapsed since the last reset.
Personal Settings (Customer-Programmable
Features)
• Speed Beep
• Trip B Data
• Set Time
• Set Data
• Autoclose
• Units (Distance, Fuel Economy, Temperature)
• Language
• Buzzer Volume
126 UNDERSTANDING YOUR INSTRUMENT PANEL

•Seat Belt Buzzer (*)
• (*) just available after SBR disable made by CHR
Service
• Service (Diesel Only)
• DRL - Daytime Running Light (if equipped)
• Exit menu
NOTE:
• If equipped with Uconnect 5.0/5.0N radio, some cus-
tomer programmable features will display in the
Uconnect 5.0/5.0N system. Refer to the Uconnect Set-
tings for further Uconnect 5.0/5.0N information.
• The Instrument Cluster Display clock setting and
Uconnect 5.0/5.0N clock setting procedure can be done
through the radio or the Instrument Cluster Display.
CYBERSECURITY
Your vehicle may be a connected vehicle and may be
equipped with both wired and wireless networks. These
networks allow your vehicle to send and receive informa-
tion. This information allows systems and features in your
vehicle to function properly. Your vehicle may be equipped with certain security fea-
tures to reduce the risk of unauthorized and unlawful
access to vehicle systems and wireless communications.
Vehicle software technology continues to evolve over time
and FCA US LLC, working with its suppliers, evaluates
and takes appropriate steps as needed. Similar to a com-
puter or other devices, your vehicle may require software
updates to improve the usability and performance of your
systems or to reduce the potential risk of unauthorized and
unlawful access to your vehicle systems.
The risk of unauthorized and unlawful access to your
vehicle systems may still exist, even if the most recent
version of vehicle software (such as Uconnect software) is
installed.
WARNING!
•
It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle systems,
including safety related systems, could be impaired
or a loss of vehicle control could occur that may
result in an accident involving serious injury or
death.
(Continued)
4
UNDERSTANDING YOUR INSTRUMENT PANEL 127

Do not store the warranty card in the vehicle.
If the electrical supply is disrupted, the unit will mute and
the display will show0000to indicate that you can enter
the security code.
You must enter the security (shown on the warranty card,
for example, 4359) code as follows:
Action Display
When you turn the radio on, the dis-
play shows 0000. 0000
Push the number 1 preset button until
the first digit of the code number is
displayed. 4---
Push the number 2 preset button until
the second digit of the code number is
displayed. 40--
Push the number 3 preset button until
the third digit of the code number is
displayed. 43--
Push the number 4 preset button until
the fourth digit of the code number is
displayed. 430-
Action
Display
When you finish entering the code,
push the POWER button to accept the
code entered. 4359
If you enter the correct code, the radio will start as normal
in radio mode (TUNER). If you enter the wrong code, the
radio will remain locked until disconnected from the
power supply.
If the car radio power supply is disconnected for approxi-
mately eight seconds or longer, you will again be asked for
the security code when it is reconnected.
General
The radio offers the following features:
Radio (Tuner Mode)
• Automatic/Manual station tuning
• Manual storage of 30 stations: 18 in the FM band (6 in
FM1, 6 in FM2 and 6 in FM3), 6 in the AM1 band and 6
in the AM2 band
• Best stations memory
130 UNDERSTANDING YOUR INSTRUMENT PANEL

MP3/WMA/AAC (USB Mode)
•“Last position” memory
• MP3/WMA/AAC track selection (forward/reverse)
• MP3/WMA/AAC track fast forward/reverse
• (RND) RaNDom (music shuffle) function
General
•Separate BASS and TREBLE settings
• BALANCE/FADE (balances left/right and front/rear
channels)
• Equalizer
• Loudness
• Digital clock in 24-hour format with weekday setting
• Illuminated buttons and display
• LCD display
• Extended functions field (Setup MENU) allows you to
change the default settings
Uconnect RH3 Display
Description Of Commands
Rotary Knob: Turn radio on and off, volume, forward/
reverse track, confirm selected option.
 And Buttons: Station search in automatic mode,
station search in manual mode, forward/reverse tracks,
forward/reverse within track.
Mute/Pause Button: Interrupts the sound by muting or
pausing the audio.
RH3 Display Panel
4
UNDERSTANDING YOUR INSTRUMENT PANEL 131

DISP Button:Switches between display modes, clock
display.
RND Button: Enables/Disables shuffle play.
SRC Button: Switches the audio source to TUNER.
Switches the audio source to USB.
Fast Track Buttons (F-Trk): Fast forward/reverse track
(used with the ROTARY knob).
Audio Button: Activates audio setting functions.
Preset Buttons (1 To 6): Store station in memory, access
preset stations.
Buttons 1 And 2: Forward/reverse folder.
Band/AS Button: Select tuned frequency band, preset best
stations.
Menu Button: Access setup menu.
General Functions And Settings
Turn The Radio On Or Off
To turn the radio on or off, push the ROTARY knob (push
once to turn on and hold for about three seconds to turn
off), not dependent on the ignition position. The default radio configuration is “Auto Switch ON
(see
SETUP MENU section). In this configuration, the radio will
follow two parameters: ignition and previous state. If the
ignition is turned off with the radio on, the radio will be
turned off, but will come on again when the ignition is
turned on. If the ignition is turned off with the radio off, the
radio continues to be turned off when the ignition is turned
on again.
If you prefer, you can set Auto Switch OFF(see SETUP
MENU section). The radio will only consider the ignition
switch position when it executes the 60 min function: when
the ignition is turned off, the radio will display the message
60 MIN for three seconds and switch off automatically
after 60 minutes if no buttons are pushed.
When it is turned on, the radio will display a greeting
message. When it is turned off, the radio will display the
message GOOD BYE before it switches off.
Audio
You can use the AUDIO button to access the available
audio settings (described in the sections below).
Equalizer
Pushing the AUDIO button for more than two seconds
activates the audio equalizer functions in the following
132 UNDERSTANDING YOUR INSTRUMENT PANEL

sequence: FLATPOPROCKCLASSICVO-
CAL
JAZZUSERFLAT. Push AUDIO repeat-
edly to change the equalization. If this button is not
pushed again within five seconds, or if you push the
ROTARY knob, the display returns to the previously
selected view and the settings will be saved.
Custom Audio Setting Functions
Push the AUDIO button for less than two seconds to
activate the Balance function.
Repeatedly pushing the AUDIO button activates the other
custom audio setting functions in the following sequence:
Bass
TrebleBalanceFaderLoudness
Bass. If this button is not pushed again within five
seconds, or if you push the ROTARY knob, the display
returns to the previously selected view and the settings
will be saved. USER equalization must be selected to
activate the Bass and Treble functions.
Bass
The display will show BASS 00to indicate that the Bass
function can be set. To increase the bass level, turn the
ROTARY knob clockwise. To decrease the bass level, turn
the ROTARY knob counterclockwise. The bass levels can be
set between -15 and 15. Treble
The display will show
TREB 00to indicate that the Treble
function can be set. To increase the treble level, turn the
ROTARY knob clockwise. To decrease the treble level, turn
the ROTARY knob counterclockwise. The treble levels can
be set between -15 and 15.
Balance
The display will show the message BAL 00to indicate
that the balance function can be set. Turn the ROTARY
knob clockwise to transfer the sound to the right-hand side;
the display will show BAL R 01. Turn the ROTARY knob
counterclockwise to transfer the sound to the left-hand
side; the display will show BALL01. The balance levels
can be set between 0 and 15.
Fader
The display will show FA D 0 0to indicate that you can set
the Fader function. Turn the ROTARY knob clockwise to
transfer the sound to the front; the display will show FA D
F01 . Turn the ROTARY knob counterclockwise to transfer
the sound to the back; the display will show FADR01.
The fader levels are set from 0 to 15.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 133

Loudness
The display will showLOUD 00to indicate that you can
set the loudness (enhanced sound) function. Turn the
ROTARY knob clockwise to enable the loudness function at
level 1; the display will show LOUD 01and the LOUD
flag will be enabled. The radio supports three loudness
levels.
Volume
Turn the ROTARY knob clockwise to increase the volume.
Turning it counterclockwise will lower the volume. The
volume can be set between 0 and 30.
Tuner Mode (AM/FM Radio)
When you enter TUNER mode, the radio tunes to the most
recently selected station and will remain on the most
recently selected frequency band. In this mode of operation the display will show one of the
following 5 codes:
CH (Channel)
When this is on, it indicates that the current radio station
preset is stored in memory. The code is only shown when
the tuned frequency is showing on the display.
ST (Stereo)
When this is on, it indicates the radio station is transmit-
ting.
Searching for Stations In Automatic Mode
When you push
orfor less than two seconds, the
radio will search for the next valid station. While the
radio is searching for the new station, the display will
show SEEKING. When the search is complete, the
display will show the tuned frequency band and station
in the format F1 106.9or, if the station was previously
stored in memory, the display will show the channel
where it is stored and the tuned station.
134 UNDERSTANDING YOUR INSTRUMENT PANEL